To p. edict the performance of a loge centrifugal pump, its model, having the following specification, was made: P = 24 IIP H=8 m N=925 rpm %3D Diameter of model pump impeller is 9 times smaller than that of the prototype. The prototype pump has to work against a head of 30 m. Find its working speed and HP required to drive it. Determine also the rate of flow of both the pumps. (35.2 m/ sec, 134 rpm, 14,100 HP)

To p. edict the performance of a loge centrifugal pump, its model, having the following specification, was made: P = 24 IIP H=8 m N=925 rpm %3D Diameter of model pump impeller is 9 times smaller than that of the prototype. The prototype pump has to work against a head of 30 m. Find its working speed and HP required to drive it. Determine also the rate of flow of both the pumps. (35.2 m/ sec, 134 rpm, 14,100 HP)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

EX1: Given are the following data for a commercial centrifugal water pump: r1 =10 cm, rz = 17.5 em, B1 =30°, B2 =20°, speed =1440 r/min. Estimate (a) the design point discharge, (b) the water horsepower, and (c) the head if bs = bz = 4.4 cm.(Hint. design point discharge, i.e €:=90°)
EX1: Given are the following data for a commercial centrifugal water pump: r1 =10 cm, r2 = 17.5 cm, By =30°, B2 =20°, speed =1440 r/min. Estimate (a) the design point discharge, (b) the water horsepower, and (c) the head if by = b2 = 4.4 cm.(Hint. design point discharge, i.e 11=90°)
Data measured during tests of centrifugal pump driven at 3000 rpm are Parameter Inlet, Section 1 Outlet, Section 2 Gage pressure, p (kPa) 90 Elevation above datum, z (m) 10 Average speed offlow,V (m/s) The flow rate is 15 m3 /hr and the torque applied to the pump shaft is 6.5 N.m. The pump efficiency is 75%, and the electric motor efficiency is 85%. Find the electric power required, and the gage pressure at outlet, section 2. Write the pump specific speed in terms of the flow coefficient and the head coefficient.
a centrifuagal pump is to be built that delivers 1000 gpm agains ahead of 120 ft operates at 1780 rpm. a model pump operating at the same effiviciency as the larger pump delivers 120 gpm against ahead of 30 ft . determine the rotation rate for the smaller , homologus pump . Using ONLY AFFINITY LAWS thanks
Q Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
4. "Pump A" usually operates at 1800 rpm using a 6 inch impeller, and its performance is described by the equation h, = 22-0.21 Q?. A homologous pump (i.e., "Pump B") from the same manufacturer operates at 1600 rpm with an 8 inch impeller. What is the performance curve for "Pump B"?
When designing an impeller for a centrifugal pump, you would consider the following materials attributes. [M ten waaler vir 'n sentrifugale pomp ontwerp, sal jy die volgende materiaal eienskappe in ag neem.] O A. creep strength and density O B. hardness and chemical composition O C. toughness and stiffness O D. hardness and thermal expansion
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) the pump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
1(C) A centrifugal pump has an impeller of diameter (D) of 300mm. When pumping 20°C water at a fixed rotational speed of 1500 RPM, the measured flow rate Q and pressure rise Pare given by the manufacturer as follows: Flow Rate (L/s) 13 19 25 32 38 44 Pressure Rise (Bar) 2.5 2.4 2.35 2.2 2.0 1.6 It is desired to use the same pump, running at 945 RPM, to pump 20°C water at 22L/s. According to your dimensionless correlation, what pressure rise p is expected?
This course EHide block A centrifugal pump with the following impeller dimensions is used to pump water. The pump is running at 1000 rpm. The ideal head rise through the pump is 190 ft. b2 Poz 72 by The parameters of the impeller are as follows: r2= 9in, b2=3in, B2= 31° Take g= 9.81 m/s23 32.2 ft/s2 pw = 998 kg/m3 = 1.94 Slug/ft. Determine the theoretical flow rate in gpm Choose.. Determine the theoretical Power shaft in (hP) Choose...
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) thepump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
A single stage centrifugal pump has an impeller of 250 mm diameter which rotates at 1,800 rpm and lifts 60 lit/sec to 25 m with an efficiency of 70%. Obtain the number of stages and diameter of each impeller of a similar multi-stage pump to lift 75 lit/sec to 175 m at 1,500 rpm. (8 stages ; 280 mm dia)