Through operation of the push button on the actuating valve, metal stampings lying in random position are sorted out and transferred to a second conveyor belt. The forward motion of the piston rod of a single acting cylinder (1A) takes T=.04 seconds. When the push buttons is released the piston rod travels to the retracted end position. A pressure gauge is fitted before and after the one-wat flow control valve. Draw the circuit diagram of this problem with complete component and port designation. -List the components used in the problem and the explanation of the circuit diagram

Through operation of the push button on the actuating valve, metal stampings lying in random position are sorted out and transferred to a second conveyor belt. The forward motion of the piston rod of a single acting cylinder (1A) takes T=.04 seconds. When the push buttons is released the piston rod travels to the retracted end position. A pressure gauge is fitted before and after the one-wat flow control valve. Draw the circuit diagram of this problem with complete component and port designation. -List the components used in the problem and the explanation of the circuit diagram

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter24: Expansion Devices

Section: Chapter Questions

Problem 12RQ: Explain the following terms as they apply to electronic expansion valves: step motor offset error...

See similar textbooks

Similar questions

the hydraulic cycle in figure consist of:8- 2 EF Pressure gauge 7 www 5 6 check valve X LR O relief valve www. M spring control valve 3 solenoid control valve Feed direction
Circuit Design - aircraft system application Draw the circuit of the flap and aileron actuation system of a small aircraft. The hydraulic system uses a variable engine driven pump as power supply. The pump takes flow from a reservoir. The circuit is protected against overload by a pressure relief valve. The speed and the direction of rotation of the flap motor are controlled using an electrically operated proportional valve. The aileron actuator contains a double acting cylinder, which is also controlled by an electrically operated proportional valve. Draw the circuit using ISO standard! Use the following symbol for the electrically operated proportional valve THEL
Circuit Design - aircraft system application Draw the circuit of the flap and aileron actuation system of a small aircraft. The hydraulic system uses a variable engine driven pump as power supply. The pump takes flow from a reservoir. The circuit is protected against overload by a pressure relief valve. The speed and the direction of rotation of the flap motor are controlled using an electrically operated proportional valve. The aileron actuator contains a double acting cylinder, which is also controlled by an electrically operated proportional valve. Draw the circuit using ISO standard! Use the following symbol for the electrically operated proportional valve JIHEL
Examine the circuit shown below and answer the following questions: 1. How is the cylinder 3A (towards the right) fundamentally different than cylinders 1A and 2A? 2. Describe 5 key features (ways, actuator, etc.) of the directional control valve 1V1. 3. Describe 5 key features of directional control valve 3V. 4. What type of device is 1V2? 5. Here's a close up of 1V2. Is it metering-in or metering-out? How do you know? 6. Empty triangle shapes appear in many places in this schematic. What do they represent? 1A 181 182 2A 282 3A 281 381 WWE 1V2 1V3 2V2 2V3 1V1 2V1 2Y1H svos H2Y2 3Y1 V 1V3 OV] OY1 211AM OZ
Match the symbol to the component: а. Pump b. Motor c. Cylinder with retract cushion d. Pressure control valve used as pressure relief e. Needle valve f. Four way valve with spring and solenoid 1 2 4 3 5 6.
Problem Description Components are to be continuously stamped with a stamping device. After the start button is pressed, the die is pushed down and the component is stamped. The die is to return to initial position after five (5) seconds. The sequence stops automatically after five (5) cycles. Start button should reset the counter. Inductive sensors S1 and S2 are used to check the fully retracted and extended positions of the cylinder. Draw the following: Pneumatic circuit diagram Electrical circuit diagram
the hydraulic cycle in figure consist of:7- 1 Pressure gauge www tank 6 accumalator X intensifier ww 3 3 way 2 position control valve Feed direction & *
(B) Choose the correct answer for the following statements:- 1- For a faster response time, a spool type of directional control valve use a-Over lapping, b-Zero lapping, c- Under lapping, d- Non of them
Respond with TRUE if the symbol of the valve shown below is drawn correctly. ABS P. R Select one: True False
When using a flow control valve (needle valve) to control the speed of actuation of a cylinder, what needs to be added to the valve in order to maintain that speed under varying load pressures and why?
Choose correct answer: In direction control valve symbol with numbering system 2, 4,6&8 indicates exhaust ports. Select one: True False
1. Two double acting pneumatic cylinders (A, B) in a process industry should extend together at the same time to open two different valves. On the return stroke both cylinder rods return at the same time. The starting is by a detent switch. Both the cylinders are of the same size with the same stroke length. In terms of notation, the cycle is required to go on till the detent start-up switch is pressed again. Draw the electro pneumatic circuit neatly. Briefly explain its operation. LB +J LB A В Y Y Y Y V