Three single-phase step-up transformers rated at 50 MVA, 13.2 kV/80 kV are connected in delta-wye on a 13.2 kV transmission line. If they feed a 120 MVA load, calculate the following: a. The secondary line voltage b. The currents in the transformer windings c. The incoming and outgoing transmission line currents
Q: The amplitude of the carrier is Ac = 10. 1. Determine the (time domain) expression for the lower…
A: Single Sideband (SSB) modulation is a technique used in communication systems to transmit…
Q: Explain more please
A:
Q: 1-10 In your own words, describe the functionality and purpose of RC circuits. 1-11 True or false:…
A: Given Data:-Here, we have been given three questions regarding RC circuits.Required Data:-Here, we…
Q: For a BPSK modulator with a carrier frequency of 70 MHz and an input bit rate of 10 Mbps, determine…
A: Given Data:Carrier frequency is and the input bit rate is 10 Mbps.Required Data:Here, we need to…
Q: determine the following by DC Analysis. a. IDQ b. VGse c. VDS RD=4 KOhms VGG=2volt
A: Given Data:Required Data:Here, we need to determine a. IDQ b. VGS c. VDSQ.
Q: An ideal single-phase source, 240 V, 50 Hz, supplies power to a load resistor R= 100 Ohm by full…
A: In this question, we need to determine the average current, rms value of current and power…
Q: [ E f 2z 2x Zy Given: 2y = 2z = E = f = 20 <-16 ohms 2039 ohms 150 < 10 volts 75 Hz Compute the…
A:
Q: The total current I entering the circuit shown in the figure is I 332-13° A. Obtain the branch…
A: In this question we need to find the voltage Vx and the current Ix shown in the given circuit.
Q: Consider the open loop transfer function KG(s) 82 K(8+2)2 of a unity negative feedback system. Plot…
A: Given Data:The open-loop transfer function is given as,
Q: 5.1 Calculate the current on the LED D1 5.2 Calculate the current on the LED D2 5.3 Calculate the…
A: In the given questions we need to calculate the ID1 , ID2 and IBat1.For given value of supply, diode…
Q: Find Vo in the given circuit. -j2Ω 2/90°A j4Ω( 2<0°V j2 Ω j8 Ω + 0
A:
Q: 43. The feedback system shown below oscillates at 2 rad/s when R(S)+ ha (A) K = 2 and a = 0.75 (C) K…
A: Given Data:A negative feedback closed-loop control system is given in the figure.Required Data:Here,…
Q: definition of cabinets and communication equipment in Metal-Clad systems
A: Metal-clad cabinets for communication equipment are designed to house and protect electronic and…
Q: Questions How does the AC version of Thevenin’s theorem compare with the DC version?…
A: we need to answer all three questions:How does the AC version of Thevenin’s theorem compare with the…
Q: A scheme in which several channels are interleaved and then transmitted together is known as
A: Given Data:A scheme in which several channels are interleaved and then transmitted together is known…
Q: Consider the Circuit shown. + YR - i M 30-22 V₂ = 10/0V t → f=1KHZ Find V₂ (t). + VL mmm 20mH + Nc -…
A:
Q: Consider the Circuit shown below. Iy ↑ R3 2.2 ks 7.5 ΚΩ R4 R₁ 39.1 ΚΩ E₁18 V + R5 56.8 ΚΩ + E₂3V R₂…
A: The given circuit isWe need to determine the currents IX and IY using mesh analysis.
Q: Battery charger and batteries Metal-Clad systems
A: we need to explain battery charger and batteries Metal-Clad systems.
Q: Consider the three single-phase two-winding transformers shown in Figure. 3. The high-voltage…
A:
Q: 1-In Figure 1, if Hr1=1, Hr2-2, E1-3, E2-4, a=0, find the intrinsic impedance n₁=? a)69.28m b)60.00T…
A:
Q: Problem 11. What can we do to increase the received RSSI (received signal power)? a. Increase…
A: We need to select correct option for given statement
Q: Determine the output states for this J-K flip-flop, given the pulse inputs shown: 1Q K U O 10 गणन Q…
A:
Q: Q2 A digital circuit with four inputs (En, A, B, C) and one output (F) is to be designed. The output…
A:
Q: Use repeated source transformation to find I, 4MA 34 $24 un LOK 4k 4MA 工。 12V
A: Given Data:A DC resistive circuit of,To Find:The current through the source.
Q: The system y(t)=tx(t-2) is * Olinear time varying Ononlinear time invariant Olinear time invariant…
A: " Since you have asked multiple questions, we will solve the first question for you. If you want…
Q: Use the bilinear transformation to design a first order low-pass Butterworth filter that has 0.2π. a…
A: FILTERS:It is devices or circuits that pass only certain frequencies and block other…
Q: A 3-phase transformer bank is made up of 3 x 50 kVA. 13.8 kV / 600 Y transformers, connected…
A: Given Data:A three-phase, transformer bank with three numbers of transformers. Each transformer is…
Q: 1. Three particles are positioned at the vertices of an isosceles triangle as shown in the figure…
A: Three charges, q1=+2q, q2=+q, q3=−q, are placed at vertices of an isosceles triangle such that a=2b.
Q: Solve the following questions regarding the BJT transistor circuit shown below
A: Given Data:For the given BJT we have Required Data:Here, the currents IB and IC are given in the…
Q: 2. A circuit with R=2000, L = 230mH, C = 15μF. The voltage supply is v = 36sin 377t. Determine: a.…
A:
Q: Let us find the solution to the difference equation y(n) - 0.25y(n - 2) = x(n) for x(n) = u(n)…
A: The difference equation of a system is given by⇒y[n]−0.25y[n−2]=x[n] ;The initial conditions are…
Q: Describe the general procedures to apply Thevenin’s theorem and Norton's theorem to both DC and AC…
A: The above question is based on Thevenin and Norton's theorems in network analysis.
Q: Q6 Given that the Boltzmann's constant is 8.617343 x 10 eV/K, with the thermal voltage at room…
A:
Q: 6.3Problems based on Inverse Laplace Transforms of derivatives of F(s) 1. Find L S (s²-a²)²
A: Given Data:Required Data:Here, we need to calculate the inverse Laplace transform of the given…
Q: Which of the following expressions constitutes a Fourier synthesis equation? (Note: Fourier…
A: A Fourier series is a way to represent a periodic function as the sum of simple sine and cosine…
Q: E-3axCos(1010°t-10z)) Find the phase velocity. (find the phase velocity) O a. 10^6 m/s O b. 2x10^6…
A:
Q: Consider a unity (negative) feedback system with loop transfer function G(s) with Bode plots…
A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…
Q: 2. Consider the circuit below, determine the impedance. Express the answer in polar form and…
A: Given Data:The RL and RC circuits with,Supply voltage Supply frequency To Find:The impedance of the…
Q: Cabinet for communication equipment in Metal-Clad. systems and their IEEE and IEC Standards
A: IEEE standards are documents developed by the Institute of Electrical and Electronics Engineers…
Q: 6. Design a 3-bit counter which counts in the sequence 0, 1, 2, ..., 7, 0, 1, ... . The counter…
A: The 3 bit counter with the given counting sequence needs ro be designed with the help of flip flop…
Q: Implement a full-adder circuit with a decoder and two OR gates.
A: Given Data:-A decode and two OR gates are given.Required Data:-Here, we need to Implement a full…
Q: Implement 8 bit comparator using two 4 bit comparators and gates
A: Given Data:Here, we need to implement a 8-bit comparator using two 4-bit comparator and additional…
Q: A rectangular waveguide has a cross-sectional area of 10cm x 5cm. Which of the following frequencies…
A: In this question, we need to choose the correct option. Which frequencies can propagate inside the…
Q: Using the Routh-Hurwitz Criterion, determine the number of RHP, LHP, and jw poles for the transfer…
A: For the given transfer function the stability of the system needs to be obtained by using the Routh…
Q: 5. Find the DTFT{x1[n] * x2[n]} +-{ x₁ [n] = 1 n = −m, -m+1, -m+2,...m-1, m 0 otherwise x₂[n] = n>0…
A: The given discrete signals areWe need to determine the DTFT{x1[n]}.
Q: Determine VCE and Ic in the non-stiff voltage-divider biased transistor circuit shown below if…
A:
Q: 10. If the maximum value of the current is what will be the value of the average curre a) 10/π A b)…
A: Given Data:Required Data:Here we need to find the average value of current.Here we need to find…
Q: The switch has been in position a for a long time. At t = 0, it turns to position b. Use Laplace…
A: The circuit diagram,
Q: For the CMOS circuit below, what is the voltage labeled Vo? 0-5 V ☐ -0.9 V O-4.1 V +5 V Vtn = |Vtpl…
A:
Q: The squre loop in the Figure is coplanar with a long, straight wire carrying a current I(t) = 7cos(1…
A: The figure is shown below,
Step by step
Solved in 5 steps with 8 images
- In per-unit equivalent circuits of practical three-phase transformers, under balanced thr-phase operation, in which of the following connect ions would a phase-shifting transformer come up? (a) Y-Y (b) Y- (c) -Consider a bank of this single-phase two-winding transformers whose high-voltage terminals are connected to a three-phase, 13.8-kV feeder. The low-voltage terminals are connected to a three-phase substation load rated 2.0 MVA and 2.5 kV. Determine the required voltage, current, and MVA ratings of both windings of each transformer, when the high-voltage/low- voltage windings are connected (a) Y-, (b) -Y, (c) Y-Y, and (d) -.A bank of three single-phase transformers, each rated 30MVA,38.1/3.81kV, are connected in Y- with a balanced load of three 1, Y-connected resistors. Choosing a base of 90MVA,66kV for the high-voltage side of the three-phase transformer. spify the base for the low-voltage side. Compute the per-unit resistance of the load on the base for the low-voltage side. Also, determine the load resistance in ohms referred to the high-voltage side and the per-unit value on the chosen base.
- Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.The ideal transformer windings are eliminated from the per-unit equivalent circuit of a transformer. (a) True (b) FalseThe ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
- In developing per-unit equivalent circuits for three-phase transformers. under balanced three-phase operation. (i) A common Sbase is selected for both the H and X terminals. (ii) The ratio of the voltage bases Vbase/VbaseX is selected to be equal to the ratio of the rated line-to-line voltages VratedHLL/VratedXLL. (a) Only one of the above is true. (b) Neither is true. (C) Both statements are true.Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit leakage reactance, are connected as a three-phase extended autotransformer bank, as shown in Figure 3.36(c). The low-voltage winding has a 110 volt rating. (a) Draw the positive-sequence phasor diagram and show that the high-voltage winding has a 479.5 volt rating. (b) A three-phase load connected to the low-voltage terminals absorbs 6 kW at 110 volts and at 0.8 power factor lagging. Draw the per-unit impedance diagram and calculate the voltage and current at the high-voltage terminals. Assume positive-sequence operation.For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
- Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is referred from one side to the other. (a) True (b) FalseAn ideal transformer has no real or reactive power loss. (a) True (b) FalseA 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.