Three reservoirs Z, Y, and X meet at junction P. Reservoir Y (25m above Reservoir X) is at Elev. 282m. Pipe Diameter (mm) Length (m) C Pipe Z 750 988 100 Pipe Y 900 1410 110 Pipe X 600 1022 90 If the rate of flow from the highest reservoir, Reservoir Z, is 605 L/s, then: What is the elevation of the highest reservoir, Reservoir Z, to the nearest whole number? Elev. 281 m Elev. 307 m Elev. 285 m none of the choices

Three reservoirs Z, Y, and X meet at junction P. Reservoir Y (25m above Reservoir X) is at Elev. 282m. Pipe Diameter (mm) Length (m) C Pipe Z 750 988 100 Pipe Y 900 1410 110 Pipe X 600 1022 90 If the rate of flow from the highest reservoir, Reservoir Z, is 605 L/s, then: What is the elevation of the highest reservoir, Reservoir Z, to the nearest whole number? Elev. 281 m Elev. 307 m Elev. 285 m none of the choices

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Three reservoirs A, B, and C are connected by pipelines 1, 2, and 3 respectively which merges at a junction X. The elevation of reservoir A is 300 m and that of B is 285 m. The rate of flow from reservoir A is 1.4 m/s. Diameter Length Friction Factor Pipe 1 800 mm 1500 m 0.0157 2 600 mm 450 m 0.0162 3 450 mm 1200 m 0.0177 Find the rate of flow in reservoir B. Calculate the rate of flow in reservoir C. Solve the elevation of reservoir C.
Determine the flow in each pipe in the reservoir shown below. Use the values provided in the table. Elevation Reservoir A 80m в 50m 20m Pipe Diameter Length friction factor AP 400mm 1800m 0.027 BP 500mm 2000m 0.02 СР 700mm 3500m 0.025 El. A El. El.
A pipe, diameter 15 cm, leaves a straight pipe with a diameter of 10 cm at point A, and later rejoins it at a downstream point B. The distance AB on the straight 10 cm pipe is 700 m. How long will the 15 cm pipe have to be in order that the flow in the two parallel pipes may be equal? Use f=0.020, and neglect minor losses. 4892 m. 5315 m. 6072 m. 4367 m.
The three reservoirs, A, B and C are connected by pipelines A, B and C respectively which meets at the junction X. The elevation of reservoir A is equal to 300 m while that of B is 285 m. The discharge flowing out of reservoir A is 1.4 cu.m/sec. (Pipes, Diameter, Length, Friction factor "f")A, 800 mm, 1500 m, 0.0157B, 600 mm, 450 m, 0.0162C, 450 mm, 1200 m, 0.0177 (a) Compute the rate of flow in reservoir B in cu.m/sec. (b) Compute the rate of flow in reservoir C in cu.m/sec. (c) Compute the elevation of Reservoir C in meters.
Two open cylindrical tanks are connected by an orifice having a cross sectional area of 0.164 m^2. Tank A is 8 m. in diameter and its water level is 10m. above that of B whose diameter is 5 m. If the coefficient of discharge is 0.60. Find the discharge flowing in the orifice. 10m A 138 m3/s 422 45 m3/s5 165.02 m/s/0 00330 m 3 B
The elevations of water surfaces in reservoirs A and B are 300 ft and 250 ft, respectively, and discharge Q1 = 50 ft³/s. Determine the following: a. the elevation of the surface of reservoir C, El C. pipe L (ft) d (in) f 1 5000 36 0.0157 2 1500 24 0.0162 3 4000 18 0.0177 A В
Q5:In a rectangular channel, the flow has a free overflow. The velocity measurement at the end section where the flow was curvilinear is indicated in figure. Estimate the discharge per unit width of the channel. adt ststuplo woft launsido-nego ne 1975-200 15°b szeng pisatzoabyd 10 cm 10 cm 10 cm 10 cm S vela 12° .8° 4° 0.85 m/s 0.90 m/s 1.00 m/s 1.20 m/s vel
10. Determine the flow in each pipe in the figure shown and the elevation of reservoir C if the inflow to reservoir A is 515 lit/sec. El. 7 B. 90 m E. 90 m B. D. 300m-450 mm El. 80 m 600m-600 mm f 0.025 300m-450m f0.03 600m 450 mm
Q7/ Lake A losses feed Lake B. The distance between them is 3.5 km. Lake A has a water level of +1100 m and Lake B has a water level of +1060 m. K = 12.5 m/ day. Calculate the specific flow rate (q) for unit area ( .assume area=1) 3.5 Km hthe W.L=1060 m W.L 1100 m Dates pous S via S total bead total head
A pump having the characteristics curve is given below delivers water from a river at elevation 52 m to a reservoir with a water level of 85 m, through a 350 mm diameter coated cast iron pipeline, 2000 m long having a friction coefficient of 0.022. Neglect all minor losses. What will be the discharge (Qs) by connecting second identical pump in parallel? Pump characteristics Q(l/s) H(m) 0 50 50 46 100 36 150 18
Reservoirs A, B, and C are connected by pipelines 1, 2, and 3 respectively which meets at the junction D. Reservoir A is at elevation 80 m, reservoir B is at elevation 50 m, and reservoir C is at elevation 10 m. Diameter Length Friction Factor 400 mm 500 mm Pipe 1800 m 2000 m 1 0.02 2 0.025 3 800 mm 4000 m 0.03 a. Compute the discharge flowing out of reservoir A. b. Determine the discharge flowing in or out at reservoir B. c. Find the discharge flowing towards reservoir C.
5. A pipe has a diameter of 0.25 m and a discharge of 1 m/s. what is the velocity in the pipe: a. 0.25 m²/s b. 1 m/s c. 4 m²/s d. 20 m/s