The width of the expansion joint is 30 mm in a cement concrete pavement. The laying temperature is 30°C and the maximum slab temperature in summer is 70°C. The coefficient of thermal expansion of concrete is 10 x 10-6/°C and the joint filler compresses upto 40% of the thickness. The spacing between expansion joint should be

The width of the expansion joint is 30 mm in a cement concrete pavement. The laying temperature is 30°C and the maximum slab temperature in summer is 70°C. The coefficient of thermal expansion of concrete is 10 x 10-6/°C and the joint filler compresses upto 40% of the thickness. The spacing between expansion joint should be

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter20: Design Of Rigid Pavements

Section: Chapter Questions

Problem 12P

See similar textbooks

Similar questions

If width of the expansion joint is 1.7 m in a cement concrete pavement. The laying temperature is 38°C and the maximum slab temperature in summer is 50°C. The coefficient of thermal expansion of concrete is 4 x 10-5 mm/mm / °C and the joint filler compresses upto 28% of the thickness. The spacing between expansion joints is S mm then Value of S is mm.
ve st Semest desi Q4) Concrete is required for walls of a building that will be moderately exposed to Intrained freezing and thawing. The cross section of a wall is 300 x 1500 mm. The smallest spacing between reinforcing steel is 50 mm. The specified compressive strength of Compressive strengthe 3 concrete at 28 days is 21.5 MPa and a slump of 50 mm. Portland cement type I is used with specific gravity of 3.15, maximum size of aggregate 25 mm and fineness modulus of fine aggregate is 2.4, absorption capacity and moisture content of fine aggregate are of 0.8%, and 1.75% respectively. The dry-rodded unit weight of coarse aggregate is 1650 kg/m³, absorption capacity and moisture content of coarse aggregate are of 0.8%, and 1.75% respectively. Both aggregates have a bulk specific gravity (SSD) of (2.65. The aggregates conform to the ASTM C33-84 requirements for grading. Estimate the quantity of (cement, fine aggregate, coarse 94 8.75 aggregate and water) for 1m³ concrete. Tooox 2.65 alka…
Q- The width of the expansion joint is 20mm in a cement concrete pavement. The laying temperature is 20 °C and the maximum slab temperature in summer is 60 °C. The coefficient of thermal expansion of concrete is 10 x 10-6 mm/mm/ °C and the joint filler compresses upto 50% of the thickness. Find the spacing between expansion joints.
FLEXURAL ANALYSIS CONCRETE UNCRACKED Problem: Determine the cracking moment for the section shown below if = 4000 psi and the modulus of rupture f, = 7.5/f'. 22" 30" 3 #9• 4" te 12–
Derive an expression for loss due to friction in Prestresed concrete.
if the depth of compression block in the concrete at failure is 130 mm. calculate the maximum possible value of the neutral axis in mm
The grade of the concrete is M25. Find the values of design strength in- 1. Direct Compression. 2. Bending Compression & 3. Flexural Tension.
a 250mmx500 concrete be am is to be reinforced with 5-28mm diameter bars at tension sde. For the web-reinforcement,10mm dimater bar was used (Cc=40mm). Using 19mm diameter aggregates for the concrete mix. 1.Determine the minimum clear spacing of main bars (horizontal layer) as prescribed by the code. a. 25mm b.28mm c.19mm d.32mm 2 .Determine the minimum clear spacing of main bars (Vertical layer) as prescribed by the code. a. 25mm b.28mm c.19mm d.32mm 3. What is the effective depth of the beam a.430 b. 426 c.415 d.405 Answers. 28,25,415
2. Tensile strength of concrete is about: (20-35)% of compressive strength (45-70)% of compressive strength None of the above. Tension controlled section Balanced section Compression-controlled section 4- The reduction factor (0) is equal to 0.9 if the: Es 2 Ety + 0.003 Es S Ety + 0.003 Es Ety 5- The design method which use the factored loads is - Working stress method - Ultimate design Method - None of above 6- If p< Po therefore the section is - Under reinforced - Over reinforced - None of above
Type D (sulphate- resisting) cement major component is (choose one) a. C2S b. C3S C. C4AF d. C3A
Internal diameter and depth of cylindrical steel cup are mm and mm in Aggregate Impact Value test. А. 204 mm, 100 mm В. 61mm, 25 mm C. 150 mm, 75 mm D. 102 mm, 50 mm B.
a simply supported reinforced concrete beam has a Vf=140KN, determine if the beam can sustain the shear loads without shear reinforcements max aggregate = 25mm fc 3D 30 Мра fy = 400 Mpa Exposure Člass = f2 %3D ot 100 4 400 mm 8-30M