Please help me with this question im stuck hope ill find solution Thewedge is used to level the member. The coefficientof static friction between the wedge and the two surfacesof contact is = 0.17. Suppose that w = 600 N/mand a = 5°. (Figure 1)Figure2 mW< 1 of 1 >1 mPart ADetermine the horizontal force P that must be applied to begin to push the wedge forward. Neglect the weight of the wedge.Express your answer to three significant figures and include the appropriate units.P =SubmitμÁ ←ValueProvide FeedbackRequest AnswerUnits?Next >

The wedge is used to level the member. The coefficient of static friction between the wedge and the two surfaces of contact is μ = 0.17. Suppose that to = 600 N/m and a = 5°. (Figure 1) Figure (< 1 of 1 Determine the horizontal force P that must be applied to begin push the wedge forward. Neglect the weight of the wedge. Express your answer to three significant figures and include the appropriate units. P= Submit μA Value Request Answer Units ?

The wedge is used to level the member. The coefficient of static friction between the wedge and the two surfaces of contact is μ = 0.17. Suppose that to = 600 N/m and a = 5°. (Figure 1) Figure (< 1 of 1 Determine the horizontal force P that must be applied to begin push the wedge forward. Neglect the weight of the wedge. Express your answer to three significant figures and include the appropriate units. P= Submit μA Value Request Answer Units ?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.92RP: The test specimen AB is placed in the grip of a tension-testing machine and secured with a wedge....

See similar textbooks

Similar questions

The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
The test specimen AB is placed in the grip of a tension-testing machine and secured with a wedge. The coefficient of static friction at both surfaces of the specimen is s. If the wedge angle is =18, determine the smallest s for which the grip is self-locking (no slipping takes place regardless of the magnitude of the force P). Neglect the weight of the wedge.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft on the right. Compression springs between the clutch housing and the pressure plate provide the necessary pressure on the friction surface. The splines prevent the clutch plate from rotating relative to the output shaft. If Ri=4 in. and R0=9 in., determine the total force that must be applied to the pressure plate by the springs if the clutch is to transmit a torque of C=56lbft when it is new.
The crate has a weight of 490 lb and a center of gravity at G rests on the floor for which the coefficient of static friction is equal to 0.35. If the force P = 300 lb is applied as shown in the figure below. The static friction force developed between the crate and the ground is. -2 ft. 2 ft -2 ft- 2 ft 4 ft 3 ft A Figure 1 Select one: O a. 234.5-Ib O b. 300-lb O c. 240-lb O d. 610 lb 3.
The 500KN block shown is in contact with a 45°incline. The w coefficient of friction is 0.25. Determine the horizontal force P necessary to 1.Just start the block up the 45° incline 2.Just to prevent the motion down the incline. 3.lf P=400KN, what is the amount and direction of friction force?
A horizontal force of P = 100 N is just sufficient to hold the crate from sliding down the plane, and a horizontal force of P = 320N is required to just push the crate up the plane. 30° Part A Determine the coefficient of static friction between the plane and the crate. ANSWER: Us %3D Part B Find the mass of the crate. Express your answer with the appropriate units. ANSWER: m =