The top surface of a rectangular workpart is machined using a peripheral milling operation. The workpart is 735 mm long by 50 mm wide by 95 mm thick. The milling cutter, which is 60 mm in diameter and has five teeth, overhangs the width of the part equally on both sides. Cutting speed = 80 m/min, chip load = 0.30 mm/tooth, and depth of cut = 7.5 mm. (a) Determine the time required to make one pass acrss the surface, given that the setup and machine settings provide an approach distance of 5 mm before actual cutting begins and an overtravel distance of 25 mm after actual cutting has finished v in seconds. (b) What is the maximum material removal rate during the cut v in mm /sec?

The top surface of a rectangular workpart is machined using a peripheral milling operation. The workpart is 735 mm long by 50 mm wide by 95 mm thick. The milling cutter, which is 60 mm in diameter and has five teeth, overhangs the width of the part equally on both sides. Cutting speed = 80 m/min, chip load = 0.30 mm/tooth, and depth of cut = 7.5 mm. (a) Determine the time required to make one pass acrss the surface, given that the setup and machine settings provide an approach distance of 5 mm before actual cutting begins and an overtravel distance of 25 mm after actual cutting has finished v in seconds. (b) What is the maximum material removal rate during the cut v in mm /sec?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Turning Operation In a production turning operation, the foreman has decreed that a single pass must be completed on the cylindrical workpiece in 4.8 min. The piece is 400 mm long and 150 mm in diameter. Using a feed = 0.43 mm/rev and a depth of cut = 4.0 mm, what cutting speed must be used to meet this machining time requirement? Hint: Re-arrange the Tm equation to find v in m/min Tm= T.DO.L v.f 1.522
across the surface and (b) the maximum metal removal rate during cutting A slab milling operation is performed on the top surface of a steel rectangular workpiece 12.0 in long by 2.5 in wide. The helical milling cutter, which has a 3.0 in diameter and ten teeth, is set up to overhang the width of the part on both sides. Cutting speed is 125 ft/min, feed is 0.006 in/tooth, and depth of cut = 0.300 in. Determine (a) the actual machining time to make one pass across the surface and (b) the maximum metal removal rate during the cut. (c) If an additional approach distance of 0.5 in is provided at the beginning of the pass (before cutting begins), and an overtravel distance is provided at the end of the pass equal to the cutter radius plus 0.5 in, what is the duration of the feed motion.
The end of a large tubular workpart is to be faced on a NC vertical boring mill. The part has an outside diameter of 38.0 in and an inside diameter of 24.0 in. If the facing operation is performed at a rotational speed of 40.0 rev/min, feed of 0.015 in/rev, and depth of cut of 0.180 in, determine (a) the cutting time to complete the facing operation and the cutting speeds and metal removal rates at the beginning and end of the cut.
Using slot milling with a cutting tool surface width of 36mm was performed from the top surface to cut a workpiece of 85 x 42 x 8 cm into two equal parts. The milling cutter is 180 mm in diameter and has eight teeth. Cutting speed = 60 m/min, chip load = 0.35 mm/ tooth, and depth of cut = 2 mm, given that the setup and machine settings provide an approach distance of 7mm before actual cutting begins and an overtravel distance of 20 mm after actual cutting has finished, and the return time is a 4-second for idle pass stroke. Determine:- 1. What is the total machining time required for the entire workpiece? 2. The maximum metal removal rate during cutting.
A surface of 43 mm x 246 mm will be machined by using a shaper and 7 mm deep stock will be removed from the surface. The shaper is operating at 24 strokes/minute and feed is 0.7 mm/stroke. If the maximum stroke length is 827 mm and allowable depth of cut is 0.4 mm for both of rough and finish cuts, what is the total machining time, in minutes ?
Q1. Calculate the time required to machine a workpiece 170 mm long, 60 mm diameter to 165 mm long 50 mm diameter. The workpiece rotates at 440 rpm, feed is 0.3 mm/rev and maximum depth of cut is 2 mm. Assume total approach and overtravel distance as 5 mm for turning operation. Answer Q2. A gray cast iron surface 280 wide and 540mm long may be machined either on a vertical milling machine, using a 100mm - diameter face mill having eight inserted HSS teeth, or on a horizontal milling machine using an HSS slab mill with eight teeth on a 200-mm. diameter. Which machine has the faster cutting time? The values of feed per tooth and cutting speed for both processes are 0.4mm/tooth and 80m/min, respectively. The depth of cut = 3.0 mm and assume A and O equal to 5. Answer
An end milling operation is carried out along a straight line path that is 325 mm long. The cut is in a direction parallel to the x‑axis on a CNC machining center. Cutting speed = 30 m/min, and chip load = 0.06 mm. The end milling cutter has two teeth and its diameter = 16.0 mm. The x‑axis uses a DC servomotor connected directly to a leadscrew whose pitch = 6.0 mm. The optical encoder emits 400 pulses per revolution of the screw. Determine (a) feed rate during the cut, (b) rotational speed of the motor, and (c) pulse rate of the encoder at the feed rate indicated.
The following data is given for slab milling of a 300 mm long 50 mm wide mild steel block: Cutter of diameter= 60 mm; Numbers of teeth =12; Cutter speed = 120 rev/min; Depth of cut = 3.2 mm; Feed is 0.25 mm/tooth.Determine (i) Table feed in mm/min, (ii) MRR (iii) Power (iv) Torque and (v) Total machining time. Assumesuitable approach and over-run and specific energy of mild steel as 5 Ws/mm3.
1. Peripheral milling is performed on the top surface of a rectangular work part that is 350 mm long by 60 mm wide. The milling cutter is 75 mm in diameter and has five teeth. It overhangs the width of the part on both sides. Cutting speed 55 m/min, chip load 0.25 mm/tooth, and depth of cut 5 mm. Maximum material removal rate during the cut will be mm/s. (a) 1419, (b) 1429, (c) 1439, (d) 1449, (e) 1459
A cylindrical workpiece has a 14.0 in diameter and has 30 in long. It is to be turned in an engine lathe at the following cutting conditions: cutting speed = 400 ft/min, feed = 0.015 in/rev, and depth of cut = 0.150 in. Determine the time to complete one turning pass if the approach and overtravel allowances are each 0.25 in (total = 0.50 in). Note: 1 ft = 12 in
Problems 1. Peripheral milling is performed on the top surface of a rectangular work part that is 400 mm long by 50 mm wide. The milling cutter is 70 mm in diameter and has five teeth. It overhangs the width of the part on both sides. Cutting speed 60 m/min, chip load 0.25 mm/tooth, and depth of cut 6.5 mm. Determine maximum material removal rate during the cut. 2. A face milling operation removes 6.0 mm from the top surface of a rectangular piece of aluminum that is 300 mm long by 90 mm wide by 75 mm thick. The cutter follows a path that is centered over the workpiece. It has four teeth and is 100 mm in diameter. Cutting speed 2.0 m/s, and chip load 0.27 mm/ tooth. Determine maximum metal removal rate during cutting.
Consider a profile milling operation, where the initial (stock) geometry has (X,Y,Z) dimensions of 100 mm x 75 mm x 50 mm. The target part has dimensions of 95 mm x 70 mm x 50 mm. The target part is located in the centre of the stock part, i.e. the stock to be removed from all sides is equal. The operation has a cutting time of 1 minute. The tool axis is along the Z direction and the tool diameter is 12 mm having 6 cutting edges. The takes place at 54m/min feed rate of 0.2 mm/rev/tooth. Calculate the axial depth of cut ? process at a