The three-reservoir system is shown below: The elevation of Reservoir at A is 130m and at C is 30m. The flow rate at Pipe 1 from Reservoir A is 2.1 m/s. All pipes have a length of 500 meters, friction factor f = 0.02, and sizes namely: Pipe Diameter 1 (mm) = 600mm Pipe Diameter 2 (mm) = 500mm Pipe Diameter 3 (mm) = 400mm Show a solution sheet containing the following: 1. Headloss at Pipe 1 2. Headloss at Pipe 3 3. Flow rate at Pipe 3 4. Flow rate at Pipe 2 5. Headloss at Pipe 2 6. Elevation of Reservoir B

The three-reservoir system is shown below: The elevation of Reservoir at A is 130m and at C is 30m. The flow rate at Pipe 1 from Reservoir A is 2.1 m/s. All pipes have a length of 500 meters, friction factor f = 0.02, and sizes namely: Pipe Diameter 1 (mm) = 600mm Pipe Diameter 2 (mm) = 500mm Pipe Diameter 3 (mm) = 400mm Show a solution sheet containing the following: 1. Headloss at Pipe 1 2. Headloss at Pipe 3 3. Flow rate at Pipe 3 4. Flow rate at Pipe 2 5. Headloss at Pipe 2 6. Elevation of Reservoir B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A A 2 B 1 The three-reservoir system is shown below: 3 The elevation of Reservoir at A is 140m and at C is 50m. The flow rate at Pipe 1 from Reservoir A is 1.75 m/s. All pipes have a length of 500 meters, friction factor f = 0.02, and sizes namely: Pipe Diameter 1 (mm) - 600mm Pipe Diameter 2 (mm) - 500mm Pipe Diameter 3 (mm) = 400mm Determine the flowrate at Pipe 2 in Liters per second.
1. The three reservoirs shown below are connected by commercial steel pipe (e=0.045mm.). Determine the flow rate in each pipe, assuming fully turbulent flow. Neglect minor losses. clev, 80 B 4000 m 1.2 m J (elev, 0) 8'09 000€ elev. 100 A ļ 5000 m 0.6 m elev. 70 C ļ
Determine the flow in each pipe in the reservoir shown below. Use the values provided in the table. Elevation Reservoir A 80m в 50m 20m Pipe Diameter Length friction factor AP 400mm 1800m 0.027 BP 500mm 2000m 0.02 СР 700mm 3500m 0.025 El. A El. El.
Qs/Three pipes No. (1), (2) and (3) are connected in series as shown in Figure No. (4). Find flow rate fro Reservoir A to Reservoir B. Physical properties of the pipes are listed in Table below. Pipe Length of Pipe Diameter of Pipe Coefficient of friction No. L d. f (mm) | (mm) 1 300 300 0.019 150 200 0.021 250 250 0.02 Resaros A 180(m) Pipeci) Pipery Resemi PipeC) -~3
A 1 2 The three-reservoir system is shown below: 3 C The elevation of Reservoir at A is 140m and at C is 50m. The flow rate at Pipe 1 from Reservoir A is 1.75 m/s. All pipes have a length of 500 meters, friction factor f = 0.02, and sizes namely: Pipe Diameter 1 (mm) - 600mm Pipe Diameter 2 (mm) = 500mm Pipe Diameter 3 (mm) = 400mm Determine the Headloss at Pipe 1 in meters.
A 1 2 The three-reservoir system is shown below: 3 C The elevation of Reservoir at A is 140m and at Cis 50m. The flow rate at Pipe 1 from Reservoir A is 1.75 m/s. All pipes have a length of 500 meters, friction factor f - 0.02, and sizes namely: Pipe Diameter 1 (mm) = 600mm Pipe Diameter 2 (mm) = 500mm Pipe Diameter 3 (mm) - 400mm Determine the elevation of Reservoir B in meters.
A A 2 B The three-reservoir system is shown below: 3 The elevation of Reservoir at A is 140m and at C is 50m. The flow rate at Pipe 1 from Reservoir A is 1.75 m/s. All pipes have a length of 500 meters, friction factor f = 0.02, and sizes namely: Pipe Diameter 1 (mm) - 600mm Pipe Diameter 2 (mm) = 500mm Pipe Diameter 3 (mm) - 400mm Determine the headloss in meters at Pipe 2.
1. Two tanks A and B have 70 m difference in water levels, and are connected by a pipe 0.25 m diameter and 6 km long with 0.002 friction coefficient. The pipe is tapped at its mid point to leak out 0.04 m3/s flow rate. Minor losses are ignored. (a) Determine the discharge leaving tank A? (b) Find the discharge entering tank B? ha А he B Q3 h = 70 m
Three reservoirs A, B and C are connected respectively with pipes 1, 2 and 3 joining at a common junction P. Reservoir A is at elevation 80m, reservoir B at 70m and C is at 60m. Assume f=0.018 for all pipes.
4. Two reservoir A and B, feed a third reservoir C as shown in figure. Assuming constant water level in the figure and making use of the data given in the table below. Compute the discharge in each pipe. Use conventional solution. EL 205 m EL 130 m 2 EL 192 m Q₁ = 0.3963 m³/s, Q₂ = 0.4550 m³/s, Q3 = 0.8513 m³/s Pipe 1 2 3 n 0.011 0.014 0.017 Diameter Length (mm) in (m) 400 500 800 1800 2000 4000
A reservoir A with elevation 30m connected with a pump to rise the water into two reservoirs B and C 90m and 60 m respectively the amount of flow from J to B is equal 0.11 m/sec use the following data to determine the flow in each pipe and the power of the pump: LAJ 450 m, DaJ = 300 mm, LJB= 300 m, DJB = 200 m, Q JB = 0. m'/sec, LJc 600, D Jc = 150 mm,f (all Pipes) 0.02
2. Determine the flow in each pipe in the three reservoirs shown. EL. 60 m A 1800 m 500 mm f = 0.03 1800 m 400 mm f = 0.025 P 3000 m 500 mm f = 0.025 EL. 40 m B EL. 30 m C