The T-shaped structure is embedded in a concrete wall at A and subjected to the force F₁ and the force- couple system F2₂ = 1550 N and M = 1,850 N-m at the locations shown. Neglect the weight of the structure in your calculations for this problem. a.) Compute the allowable range of magnitudes for F, in the direction shown if the connection at 4 will fail when subjected to a resultant moment with a magnitude of 880 N-m or higher. b.) Focusing on the forces and ignoring given M for now. Using the value for F₁,mn that you calculated in (a), replace the two forces F₁ and F₂ with a single force that has equivalent effect on the structure. → Specify the equivalent force Fog in Cartesian components and indicate the horizontal distance from point A to its line of action (note this line of action may not intersect the structure). c.) Now, model the entire force system (Fimin. F₂, and M) as a single force and couple acting at the

The T-shaped structure is embedded in a concrete wall at A and subjected to the force F₁ and the force- couple system F2₂ = 1550 N and M = 1,850 N-m at the locations shown. Neglect the weight of the structure in your calculations for this problem. a.) Compute the allowable range of magnitudes for F, in the direction shown if the connection at 4 will fail when subjected to a resultant moment with a magnitude of 880 N-m or higher. b.) Focusing on the forces and ignoring given M for now. Using the value for F₁,mn that you calculated in (a), replace the two forces F₁ and F₂ with a single force that has equivalent effect on the structure. → Specify the equivalent force Fog in Cartesian components and indicate the horizontal distance from point A to its line of action (note this line of action may not intersect the structure). c.) Now, model the entire force system (Fimin. F₂, and M) as a single force and couple acting at the

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.6P: Find the internal force systems acting on sections 1 and 2.

See similar textbooks

Similar questions

Find the internal force systems acting on sections 1 and 2.
Determine A·(B×C) The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 11i - 10j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN Determine the magnitude of the moment of P about the origin (point O) in Nm.
Solve for the resultant forces and moments at points A and B in diagram below
Compute the magnitude of the moment MO of the 220-lb force about the axis O-O.Assume F = 220 lb, d = 17 in., H = 10.8 in., h = 5.4 in., 36°, and 61°.
Two forces L (parallel to the y-axis) and A (parallel to the z-axis) are applied at point Q on the assembly shown. The assembly is supported by a bearing at D. Answer the following questions: 1. What are the reactions at the support at D? R are force reactions and M are moment reactions. 2. Find the moment of force L about the x-axis.
Example : Replace the three forces acting on the bent beam by a single equivalent force R. Specify the distance x from the point O in which the line of action of R passes. 200 N 160 N 250 mm 250 mm -250 mm 125 mm 240 N
M=148 Nm Example : Replace the three forces acting on the bent beam by a single equivalent force R. Specify the distance x from the point O in which the line of action of R passes. 200 N 160 N 250 mm 250 mm 250 mm 125 mm 240 N REDMI NOTE 9 PRO O AI QUAD CAMERA
Determine the moment at O due to the application of the forces shown in the figure.
A steel frame is supported by 3 guy wires as shown. Cable CD exerts a tensile force of magnitude 1.2 kN, as shown in the diagram. Calculate: a. The moment of T about point A b. The projection of force T onto line OF c. The angle between cables GF and AE m 2 m G B 1m 1.5 m /C 1.5 m 3 m 1.5 m 3m T= 1.2
In the given figure below was supported at A and E by with a ball and socket and a wire at D connected to F. Determine the following given that force is equal to 687.4N: Determine the X-component of Vector DF Determine the Y-component of vector Df Determine the z- component of Vector Df Determine the moment experienced by the system assuming that there is no wire support. determine the x-component of the moment experienced by the system assuming there is no wire support Determine the y component of the moment experienced by the system assuming that there is no wire support Determine the z component of the moment experienced by the system assuming that there is no wire support determine the tension experienced by wire Df Determine the x component of the tension experienced by wire DF determine the y component of the tension experienced by wire DF Determine the z component of the tension experienced by wire DF Xb: 171. 995 xC : 477.445 Ya:200.266 ZE : 150.166 Zf : 492.252
Q3/ Calculate the moment of the 90- N force about point O for the condition 0=15. Also, determine the value of e for which the moment about O is (b) zero and (c) a .maximum F = 90 N 800 mm O A 500 mm
Replace the three forces acting on the bent pipe by a single equivalent force R. Choose point "O' as your convenient point. Calculate 1- Resultant Force "R" and Resultant Moment "Mo" at point O and show them on a diagram. 2- Specify the distance X from point "O" to the point on the x-axis through which the line of action of R passes. Show your result on a separate diagram. -10"- 40 lb -10" fort 60 lb 50 lb 10"