The surface finish specification in a turning job is 0.90 um. The work material is cast iron. The cutting conditions have been selected as follows: v = 90 m/min, f 3D0.23mm/rev, and d = 2.2 mm. The nose radius of the cutting tool must be selected. Determine the minimum nose radius that will obtain the specified finish in this operation.

The surface finish specification in a turning job is 0.90 um. The work material is cast iron. The cutting conditions have been selected as follows: v = 90 m/min, f 3D0.23mm/rev, and d = 2.2 mm. The nose radius of the cutting tool must be selected. Determine the minimum nose radius that will obtain the specified finish in this operation.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Compute and choose the nearest value of minimum number of teeth to be cut on the pinion in order to avoid interference with the help of following data: Pressure angle: 14.5o Pitch circle diameter of gear = 1500 mm Pitch circle diameter of pinion = 150 mm a. 30 b. 54 c. 18 d. 46
QUESTION 5 Determine the spindle speed (rpm), the feed rate (in/min) and the cutting power required for turning a 1º diameter copper rod with a depth of cut of 0.1" using a cemented carbide tool. O N=287 RPM, F-25.8 in/min, P=9.7 hp ON=2866 RPM, F=258 in/min, P=97 hp ON=1146 RPM, F-25.8 in/min, P=97 hp O N= 11460 RPM, F-340 in/min, P=130 hp ON= 1146 RPM, F-34 inimin, P= 13 hp ON= 115 RPM, F-3.4 in/min, P=1.3 hp QUESTION 6 It is required to face mill an aluminum block to size it down from 2" to 1.5" thick using a 3" diameter 2-toothed carbide cutting tool. The block is 6.0" wide and 6" long. The entire tool diameter engages the workpiece during the cut. Calculate the recommended spindle speed in revolutions per minute, feed per tooth, and cutting power required. O N=1529 RPM, f= 0.026 in/rev/tooth, P = 36 hp O N-3820 RPM, f= 26 in/revitooth, P=27 hp O N-3820 RPM, f= 0.052 in/rew/tooth, P=27 hp ON-382 RPM, F= 0.026 in/revitooth, P = 0.027 hp O N-3820 RPM, f= 0.052 in/rev/tooth, P=2.7 hp…
The face milling cutter of D = 200 mm used to cut a block which is 200 mm H, 1=480 mm, if f- 0.7 mm/rev is used and the overrun of the cutter is 12 mm and cutting speed 320 mm/min. Calculate the machining time. Cuttin
In crank and slotted lever quick return mechanism, the crank length is (100 +X )mm and the distance between the fixed center is (225+X)mm. The length of the slotted lever is (525+X)mm. Determine the ration of time of cutting stroke to time of return stroke. Also calculate the length of the stroke . Note where X is two digit number made from the last two digit of the registration number of the students For example if the reg. no. of the student is 11912081 then X=81 and crank length is 80+81=161mm Draw the neat and clean diagram with proper scale. Rough drawings will not be considered
Question 4: A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm thickness at rate of 35 holes per minute. It requires a torque
A 48-inch diameter saw blade is mounted on a pulley driven steel shaft; the required blade peripheral linear speed is 150 fps. Motor drive is 25 hp running at 1,200 rpm with a 6 inches diameter pulley. Determine the shaft rpm to attain the blade peripheral speed required. a. 716.2 c. 617.2 b. 761.2 d. 671.2 Determine the diameter of the shaft the motor requires. a. 3.162” c. 2.106” b. 1.186” d. 4.153” Determine the diameter of the pulley driving the steel shaft. a. 8.206” c. 6.409” b. 10.053” d. 4.605”
3. Write the NC code for the side milling with D=10 mm end mill throegh poínts 1. B. 8. 42 (00 ps 92 PaiPa 20 controlladle point of the end mill Fead rate for vertical hovement F=2000 ana Fead vate for cutling (horizantal movement) is caloulated in queatian2. P4 min . 42 PIPZ P3
Q.6 The Ray Precision Engineering company uses CNC Lathe machine. The reliability of Gear Box of CNC Lathe machine is given by: e-(Vo.002)•t t20 Evaluate the following: (i) The Reliability for the first 40 hours of operation; (ii) The MTTF and the failure rate; (iii) The Design life for a reliability of 85%.
A drilling operation is performed to create a through hole on a steel plate that is 20 mm thick. Cutting speed = 0.4 m/s, and feed = 0.20 mm/rev. The 18-mm-diameter twist drill has a point angle of 120°. Determine the following once the drill reaches full diameter: a. the machining time and, b. the metal removal rate Equation used Tm TD₂L fv
High accuracy cutting is very important in modern machining processes. This study is focus in modern machining process of EDM wire cutting with diameter wire 0.25 mm (Brass), material aluminum with thickness 10 mm and initial spark gap recommended is 50 microns. By applying the assumption value of size desired 60 mm (X, Y) and output size 59.984 (X axis) and 60.012 (Y axis). Complete the value of (A,B,C,D,E and F) in design of experimental (DOE) as in table1 and explain the result outcome methods. Table 1: Design of experimental (DOE) table Size Trial output size size of % error True or actual desired spark (mm) measurement of spark or gap gap error (mm) / side overall (mm) (mm) size A B D E F
Q-3 Three blocks A, B, and C and a grooved block D have dimensions a, b, c, and d as follows: a = 40.500 0.025 mm b = 52.000 0.075 mm c = 73.000 0.015 mm d = 165.900 0.250 mm Parts A, B, and C are standard parts supplied by vendors from the market, but we are to machine part D according to the the width that you are asked to specify. (a) Determine the mean gap w0 of w and its tolerance. (b) Determine the mean size of d (d0) that will assure that w ≥ 0.050 mm.
The outline of the part in figure below is to be profile milled, using a 20 mm diameter end mill with two teeth. The part is 10 mm thick. Cutting speed =125 m/min and feed = 0.10 mm/rev. Use the lower left comer of the part as the origin in the x-y axis system. The two holes in the part have already been drilled and will be used for clamping the part during milling, Write the part program in the APT format.