The strength of the longitudinal joint is 25 kips/ft, whereas for the girth joint it is 20 kips/ft. Calculate the maximum diameter of the cylindrical tank if the internal pressure is 120 psi. Also discuss the joint strength and diameter of tank requirement for the given conditions. SIR, PLS GIVE ME PROPER AND CORRECT ANSWER. THANKS

The strength of the longitudinal joint is 25 kips/ft, whereas for the girth joint it is 20 kips/ft. Calculate the maximum diameter of the cylindrical tank if the internal pressure is 120 psi. Also discuss the joint strength and diameter of tank requirement for the given conditions. SIR, PLS GIVE ME PROPER AND CORRECT ANSWER. THANKS

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.9P: A safety valve on the top of a tank containing steam under pressure p has a discharge hole of...

See similar textbooks

Similar questions

QUESTION 1. A hydrazine tank, designed by Orbital Propulsion Center, is made of T16A14V STA (3.7164.7) titanium alloy is shown in the figure. a. The length of the tank is 890 mm and its volume is 176.5 liters. Calculate the radius of the tank. b. Determine the tank thickness, t such that the tank resists the proof pressure of 36.9 Bar without permanent deformation and the burst pressure of 49.2 Bar without fracture. c. Under the operational conditions (MEOP), determine the absolute maximum shear stress that occurs on the tank. http://www.space-propulsion.com/spacecraft-propulsion/hydrazine-tanks/index.html Surface Tension Propellant Tank OST 33/0 Net Volume Range 176.5 Litres Propellants Hydrazine (N,H) Spherical with a gylindrical Intersection Geometrical Shape Maximum Expected Operating Pressure (MEOP) 24.63 bar Proof Pressure (1.5 x MEOP) 36.95 bar Burst Pressure (2.0 x MEOP) 49.26 bar Interface Fixation 4 Suspension Trunnions Materials - Pressure Vessel TIGAIAV STA (3.7164.7) -…
Calculate the minimum diameter for a cylindrical vessel that is to carry a gas at a pressure of 10 MPa. The thickness of the vessel is 38 mm and the hoop stress is 83 MPa and the longitudinal stress is 40 MPa. 1 Add file
A welded steel cylindrical drum made of a 10-mm plate has an internal diameter of 1.20 m. Compute the change in diameter that would be caused by an internal pressure of 1.5 MPa. Assume that Poisson's ratio is 0.30 and E = 200 GPa. OLAd 0.459 mm OIL. Ad Ⓒ III. Ad = 0.289 mm ON. Ad 0.369 mm 0.521 mm
Required : 1. Determine the safest thickness of the vessel in mm 2. If the vessel has spherical shape, what would be it's wall thickness in mm 3. Calculate the tensile force exerted on the wall cross section area in problem (2) 4. How about the bursting force in problem (2)
4. A spherical weather balloon is made of 0.2-mm-thick fabric that has a tensile strength of 10 MPa. The balloon is designed to reach an altitude where the interior pressure is 1500 Pa above the atmospheric pressure. Find the largest allowable diameter of the balloon, using 1.5 as the factor of safety.
TA 500 Ib buoy, with a 2 ft radius is tied to the bed of a lake using a steel cable. What is the tensile force in the cable?
Pls answer thank you! A round vertical steel tank has an inside diameter of 3 m and is 6.5 m in height. It contains gasoline with a density of 850 kg/m3 . If the allowable tensile stress is 25 Mpa, find the minimum thick required.
A compressed air tank has an inner diameter of 0.45 metre, and a wall thickness of 6.35 mm. It is formed by welding two steel hemispheres. i. if the allowable tensile stress is 96 MPa, what is the maximum permissible air pressure (pa) in the tank. ii. if the allowable shear stress in the steel is 40 MPa, what is the maximum permissible air pressure (pb) in the tank?
SolveSample Problem 4.1.All remain as presented, except for the following changes.The factor ofsafety is now 2, and not 3.As Presented, the thickness of the tube is uniform. In the new one that you are solving,let the thicknessesof the top and bottom be the same,ttb, and the thicknesses of theleft and right be the same,tlr.Theheightand the width of the tube are still respectively 5 in and 3.25 in.As you make thesethickness changes,you are to keep thetotal mass of the tube unchanged. Answer the same questions (a) and (b).Explain your findings
2. A spherical stainless-steel tank having an inner diameter 'D', is used to store natural gas at a pressure of 'p'. The properties of the steel are as follows: yield stress in tension is "T'; yield stress in shear is 'S' and modulus of elasticity is 'E'. The desired factor of safety with respect to yielding is F.S'. Determine the minimum permissible thickness tmin Of the tank. D=500mm, p=19MPA,T=970MPA,S=500Mpa,E=196GPA,F.S=2.8 ww.
DESIGN Situation No. 1 – A pressure vessel 360 mm in diameter it to be fabricated from steel plates. The vessel is to carry an internal pressure of 6 MPa. 1. What is the required thickness of the plate if the vessel is to be cylindrical and the allowable steel stress is 120 MPa. 2. What is the required thickness of the plate if the vessel is to be spherical and the allowable steel stress is 120 MPa. 3. If the vessel to be fabricated is cylindrical using 12 mm thick steel plate, what is the maximum internal pressure that the vessel can carry if the allowable steel stress is 60 MPa.
QUESTION 2 A thin cylindrical pipe with an inside diameter of 300 mm is 6 mm thick and fitted with end covers. It is subjected to an internal pressure of 5.2 MPa. Calculate the circumferential and longitudinal stress induced. Which axially applied compressive load would reduce the longitudinal stress to zero?