The state of stress shown occurs in a machine component made of a grade of steel for which ay 65 ksi. Using the maximum-distortion energy criterion, determine the range of values of oy for which the factor of safety associated with the yield strength is equal to or larger than 2.4. (Round the final answers to two decimal places.)

The state of stress shown occurs in a machine component made of a grade of steel for which ay 65 ksi. Using the maximum-distortion energy criterion, determine the range of values of oy for which the factor of safety associated with the yield strength is equal to or larger than 2.4. (Round the final answers to two decimal places.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

AB çubuğunun çapı 17 mm ve BC çubuğunun çapı 25,5 mm'dir. Malzemenin emniyetli gerilmesi 170 MPa ve F=P olduğuna göre uygulanabilir en büyük P kuvveti kaçtır? The diameter of the AB bar is 17mm and the diameter of the BC bar is 25.5 mm. Since the safe stress of the material is 170MPa and F = P, What is the maximum applicable Force P?
A tensile stress is to be applied along the long axis of a cylindrical copper rod that has a diameter of 2.1 mm. Determine the magnitude of the load required to produce a 0.002 mm change in diameter if the deformation is entirely elastic. Answer in N. The modulus of elasticity of copper is 110 GPa and it's Poisson's Ratio is 0.34. Round your answer to 0 decimal places.
The principal stresses at the critical point of a part were found to be as shown. Using the distortion energy theory, yielding will occur if: 300 MPa 300 MPa 300 MPa O a. the material's yield strength is less than 900 MPa. O b. the material's yield strength is less than 300 MPa. O c. None of these. O d. the material's yield strength is less than 450 MPa. O e. the compressive strength of the material is less than 300 MPa.
Required information Consider the given state of stress. Take Y = 4 ksi. 10 ksi ces Determine the normal and shearing stresses after the element shown has been rotated through 10 counterclockwise. The normal stress oy is ksi and oy'is ksi, The shear stress Tyyis ksi
Question 1 Aluminum rod E = 10400 ksi Allowable axial deformation= 0.3 in. Tension in the rod=2300 lb. allowable normal stress in the rod = 12.8 ksi, Determine the the corresponding maximum length L of the rod. Answer in inches rounded-off to 2 decimal places
Q1/ For the state of plane stress shown below, construct a Mohr's circle and determine:- (a) the principle stress acting at this point (b) the orientation of the principle stress (c) the maximum in-plane shear stress at the point and the corresponding average normal stress (d) the orientation of the maximum in-plane shear stress (e) show the results on elements 700 kPa pisres shear Stress at 100 kPa al stress aximum plar arenis ec 400 kPa
For the clevis connection shown, the shear stress in the 0.287-in.-diameter bolt must be limited to 29 ksi. Determine the maximum load P (in kips rounded to the nearest hundredths) that may be applied to the connection. Answer: Blank 1 clevis
! Required information Consider the loading shown. The allowable normal stress for the steel used is 24.8 ksi. 18 kips 3 kips/ft B -6 ft 6 ft- 3 ft For the selected design, determine the maximum value of the principal stress Omax at the junction of a flange and the web. (Round the final answer to two decimal places.) The maximum value of the principal stress Omax at the junction of a flange and the web is ksi.
The axial load 343 kN applied to the lap joint is distributed equally among the three 16-mm-diameter rivets. What is the maximum tensile stress (in MPa) in the plate if w = 135.3mm and t = 28.5mm? Round off the final answer to three decimal places. 020 bearing.png ... t t P P
The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.6-in.-diameter pin at A, and the 0.29-in.-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5001 Ib. Round off the final answer to two decimal places. 0007 P.png 70 4 in 3.5 in. 30 0.5-in dia. Detail at A
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 556 mm2 and P= 36.79 kN. Round off the final answer to four decimal places.
A state of stress at a point A is given by σx = 77 MPa, σy = 3.1 MPa, and τxy = 12 MPa. What is the maximum in-plane shear stress for the point A? Lütfen birini seçin: a. 70.7106 MPa b. 38.8497 MPa c. 83.0846 MPa d. 39.4498 MPa e. None