The small cylinder C has a mass of 10 kg and is attached to the end of a rod whose mass may be neglected. The frame is subjected to a couple M = (8t2 + 5) N · m, where t is in seconds, and the cylinder is subjected to a force of 60 N, which is always directed as shown. The cylinder has a speed vo = 2 m/s when t = 0. (Figure 1) 60 N

The small cylinder C has a mass of 10 kg and is attached to the end of a rod whose mass may be neglected. The frame is subjected to a couple M = (8t2 + 5) N · m, where t is in seconds, and the cylinder is subjected to a force of 60 N, which is always directed as shown. The cylinder has a speed vo = 2 m/s when t = 0. (Figure 1) 60 N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.78P: The chain OA is 25 ft long and weighs 5 lb/ft. Find the maximum force in the chain and the distance...

See similar textbooks

Similar questions

Р. The spring constant k = 700 N/m. The masses ma = 14 kg and mg = 18 kg. The horizontal bar is smooth. At the instant shown, the spring is unstretched and the mass B is moving downward at 1 m/s. How fast is B moving when it has moved downward 0.2 m from its present position? MA -0.3 m- wiww 0.15 m Note: Use conservation of Energy method
The small cylinder C has a mass of 10 kg and is attached to the end of a rod whose mass may be neglected. The frame is subjected to a couple of moment M = 26Nm, and the cylinder is subjected to a force of F = (5t² + 6) N, where t is in seconds, which is always directed in the same direction as the cylinder's velocity as shown. The cylinder has a speed vo= 2 m/s when t = 0. (Figure 1) Figure 0.75 m M 1 of 1 Part A Determine the speed of the cylinder when t = 3 s. Express your answer to three significant figures and include the appropriate units. v= |μA Value Submit Request Answer < Return to Assignment Units Provide Feedback ?
The weight of the spring held follower AB is 0.367 kg and moves back and forth as its end rolls on the contoured surface of the cam, where r = 0.2 ft and z = (0.1sin20) ft. If the cam is rotating at a constant rate of 6 rad/s, determine the force, in lb, at the end A of the follower where 0 = 45°. In this position, the spring is compressed 0.4 ft. Neglect friction at the bearing C. Round your answer to 3 decimal places. 6 = 6 rad/s 0.2 ftX z = 0.1 sin 20 Z A k = 12 lb/ft с B
A mass that weighs 8 lb stretches a spring 24 inches. The system is acted on by an external force of 4 sin(4t) lb. If the mass is pulled down 6 inches and then released, determine the position of the mass at any time t. Assume that the u-axis is directed downwards and ft = g 32 Express your answer as a linear combination of sin(at) $² and cos(at), where u is in feet and t is in seconds. u(t) = Determine the first four times at which the velocity of the mass is zero. Exclude t = 0 as trivial, and enter exact answers. First zero: t = Third zero: t = Second zero: t = Fourth zero: t =
Determine the acceleration of each block and tension in the cords for both of these problems. (accelerations are constant for both). Assume t1 = 0s and t2 = 1s. Given: Us = 0.3 (Between A and Surface) Hk = 0.25 mA = 50 kg MB = 220 kg Given: mA = 50 kg m³ = 20 kg mc = 8 kg mp = 0kg ус A ув B G C D B to G A УА V YD
The rate of the rotating arm is 4 rad/s when it is 3 rad/s² and 0 = 180°. Determine the force it must exert on the 0.45 kg smooth cylinder if it is confined to move along the slotted path. Motion occurs in the horizontal plane. Round your answer to 2 decimal places. 6 = 4 rad/s, 0 = 3 rad/s²/ r 0 = 180° r = (²7) m
The constant tensions of 200N and 160 N are ap- Q2 plied to the hoisting cable as shown. If the velocity v of the load is 2 m/s down and the angular velocity w of the pulley is 8 rad/s counterclockwise at time t = 0, determine v and w after the cable tensions have been applied for 5 s. Note the independence of the results. 200 N 160 N 300 mm 15 kg k = 250 mm 20 kg
The tractor is used to lift the 170-kg load B with the 24-m-long rope, boom, and pulley system. The tractor travels to the right with an acceleration of 4 m/s² and has a velocity of 5 m/s at the instant SA = 5 m. When SA = 0, SB = 0. (Figure 1) Figure 12 m -SA 1 of 1 Part A Determine the tension in the rope at this instant. Express your answer to three significant figu T = Value N Submit Previous Answers Request Answ X Incorrect; Try Again
The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined at 20o with the horizontal. Find the velocity of the block after it moves 20m starting from rest. the answer must be 3 decimal places.
The smooth surface of the vertical cam is defined in part by the curve r = (0.2 cos 0+0.3) m. Plac41 Figure ▼ Part A If the forked rod is rotating with a constant angular velocity of A = 4 rad/s, determine the force the cam and the rod exert on the 1.8-kg roller when 0 = 30°. The attached spring has a stiffnesss k= 30 N/m and an unstretched length of 0.1 m. Express your answers in newtons using three significant figures separated by a comma. Neam, Frod = ΑΣΦ Submit Request Answer vec ? 1 of 1 N
R ft Rft P lb The block of weight 131 lb is pushed with a force of P = 46 lb on top of two cylindrical rollers with a weight of 32 lb and a radius of R = 1.91 ft. Determine the block's speed after it has been moved 1.48 ft to the left. The block is originally at rest. No slipping occurs. Calculate your answer to two decimal places. Report your answer in ft/s.
Determine the force P required to maintain the 200-kg engine in the position for which e = 30o. The diameter of the pulley at B is negligible * (( take g=10 m/s2 2 m > B 2 m P OC 200 kg P= 1693.7 N O P= 1793.7 N O P=1993.7 N O P= 1893.7 N O