The slide generator in the figure below is in a uniform magnetic field of magnitude 0.0500 T. The bar of length 0.345 m is pulled at a constant speed of 0.500 m/s. The U-shaped conductor and the bar havea resistivity of 2.75 x 10-8 Q2. m and a cross-sectional area of 9.75 × 10-4 m². Find the current in the generator when x = 0.690 m. (Note that the A in the image below is the area of the loop, not thecross-sectional area of the conductor and bar.)ABulb isunlit.о○°OOOO19OΘ•O○OOΟΟOO○OOΘΘΘΘΘ©OΟΘΘOΘΟ○OA.lBulbis lit.B.○mech

Answered: Image /qna-images/answer/66114fb1-8460-4bd7-82ca-16461740131f.jpg

The slide generator in the figure below is in a uniform magnetic field of magnitude 0.0500 T. The bar of length 0.345 m is pulled at a constant speed of 0.500 m/s. The U-shaped conductor and the bar have a resistivity of 2.75 x 10-80 m and a cross-sectional area of 9.75 x 10-4 m². Find the current in the generator when x = 0.690 m. (Note that the A in the image below is the area of the loop, not the cross-sectional area of the conductor and bar.) A A. Bulb is unlit. Bulb is lit. ス i mech

The slide generator in the figure below is in a uniform magnetic field of magnitude 0.0500 T. The bar of length 0.345 m is pulled at a constant speed of 0.500 m/s. The U-shaped conductor and the bar have a resistivity of 2.75 x 10-80 m and a cross-sectional area of 9.75 x 10-4 m². Find the current in the generator when x = 0.690 m. (Note that the A in the image below is the area of the loop, not the cross-sectional area of the conductor and bar.) A A. Bulb is unlit. Bulb is lit. ス i mech

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter13: Electromagnetic Induction

Section: Chapter Questions

Problem 87CP: A 500-turn coil with a 0.250m2 area is spun in Earth’s 5.00105T magnetic field, producing a 12.0-kV...

See similar textbooks

Similar questions

Design a current loop that, when rotated in a uniform magnetic field of strength 0.10 T, will produce an emf =0 sin t. where 0=110V and 0=110V .
The square armature coil of an alternating current generator has 200 turns and is 20.0 cm on side. When it rotates at 3600 rpm, its peak output voltage is 120 V. (a) Wliat is the frequency' of the output voltage? (b) What is the strength of the magnetic field in which the coil is turning?
The conducting rod shown in the accompanying figure moves along parallel metal rails that are 25-cm apart. The system is in a uniform magnetic field of strength 0.75 T, which is directed into the page. The resistances of the rod and the rails are negligible, but the section PQ has a resistance of 0.25 . (a) What is the emf (including its sense) induced in the rod when it is moving to tire right with a speed of 5.0 m/s? (b) What force is required to keep the rod moving at this speed? (c) What is the rate at which work is done by this force? (d) What is the power dissipated in the resistor?
Two frictionless conducting rails separated by l = 55.0 cm are connected through a 2.00- resistor, and the circuit is completed by a bar that is free to slide on the rails (Fig. P32.71). A uniform magnetic field of 5.00 T directed out of the page permeates the region, a. What is the magnitude of the force Fp that must be applied so that the bar moves with a constant speed of 1.25 m/s to the right? b. What is the rate at which energy is dissipated through the 2.00- resistor in the circuit?
Consider the system pictured in Figure P28.26. A 15.0-cm horizontal wire of mass 15.0 g is placed between two thin, vertical conductors, and a uniform magnetic field acts perpendicular to the page. The wire is free to move vertically without friction on the two vertical conductors. When a 5.00-A current is directed as shown in the figure, the horizontal wire moves upward at constant velocity in the presence of gravity. (a) What forces act on the horizontal wire, and (b) under what condition is the wire able to move upward at constant velocity? (c) Find the magnitude and direction of the minimum magnetic Field required to move the wire at constant speed. (d) What happens if the magnetic field exceeds this minimum value? Figure P28.26
A circular loop of wire with a radius of 4.0 cm is in a uniform magnetic field of magnitude 0.060 T. The plane of the loop is perpendicular to the direction of the magnetic field. In a time interval of 0.50 s, the magnetic field changes to the opposite direction with a magnitude of 0.040 T. What is the magnitude of the average emf induced in the loop? (a) 0.20 V (b) 0.025 V (c) 5.0 mV (d) 1.0 mV (e) 0.20 mV
How many turns must be wound on a flat, circular coil of radius 20 cm in order to produce a magnetic field of magnitude 4.0105 T at the center of the coil when the current through it is 0.85 A?
Within the green dashed circle show in Figure P30.21, the magnetic field changes with time according to the expression B = 2.00t3 4.00t2 + 0.800, where B is in teslas, t is in seconds, and R = 2.50 cm. When t = 2.00 s, calculate (a) the magnitude and (b) the direction of the force exerted on an electron located at point P, which is at a distance r = 5.00 cm from the center of the circular field region. (c) At what instant is this force equal to zero? Figure P30.21
The flip coil of the preceding problem has a radius of 3.0 cm and is wound with 40 turns of copper wire. The total resistance of tire coil and ballistic galvanometer is 0.20 When the coil is flipped through 180° in a magnetic fielda change of 0.090 C flows through the ballistic galvanometer. (a) Assuming that and the face of the coil are initially perpendicular, what is tire magnetic field? (b) If the coil is flipped through 90°, what is tire reading of the galvanometer?
A 0.50-kg copper sheet drops through a uniform horizontal magnetic field of 1.5 T, and it reaches a terminal velocity of 2.0 m's. (a) What is the net map,-, eh: force on the sheet after it reaches terminal velocity? (b) Describe the mechanism responsible for this force, (c) How much power is dissipated as Joule heating while the sheet moves at terminal velocity?
A wire of length 1.0 m is wound into a single-turn planar loop. The loop carries a current of 5.0 A, and it is placed in a uniform magnetic field of strength 0.25 T. (a) What is the maximum torque that the loop will experience if it is square? (b) If it is circular? (c) At what angle relative to B would die normal to the circular coil have to be oriented so that the torque on it would be the same as the maximum torque on the square coil?
A 500-turn coil with a 0.250m2 area is spun in Earth’s 5.00105T magnetic field, producing a 12.0-kV maximum emf. (a) As what angular velocity must the coil be spun? (b) What is unreasonable about this result? (c) Which assumption or premise is responsible?