The shaft is made of A992 steel. It has a diameter of 0.7 in. and is supported by bearings at A and D, which allow free rotation. The shear modulus of elasticity for the material is 11 × 10³ ksi. A 2 ft Part A B 2.5 ft 60 lb-ft C 3 ft 60 lb-ft D Determine the angle of twist of B with respect to D.

The shaft is made of A992 steel. It has a diameter of 0.7 in. and is supported by bearings at A and D, which allow free rotation. The shear modulus of elasticity for the material is 11 × 10³ ksi. A 2 ft Part A B 2.5 ft 60 lb-ft C 3 ft 60 lb-ft D Determine the angle of twist of B with respect to D.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

回の shear stress tmax in any of the three bars? P3 9 m P 135° up. (D 135° 90 dz s applied Knowing the steel the steel 09. A circular steel tube of length L = 0.90 m is loaded in torsion by torques T. s in the (a) If the inner radius of the tube is r, = 40 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y1 (in radians) at the inner surface? (b) If the maximum allowable shear strain is 0.0005 rad and the angle of twist is to be kept at 0.5° by adjusting the torque T, what is the maximum permissible outer radius (r2)max? B 12 mm is to be of ACR
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm, If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 2. A 200mm 250mm 300mm 30 N-m 20 N-m 80 N-m O 0.94MPA O 4.68MPA O 187MPA O 2.81MPA
The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel with the following properties: elastic modulus, E=200 GPa and Shear Modulus, G=75 GPa, Tb-80Nm Determine the following: a. Absolute the maximum torsional shear stress b. Angle of twist of the end B with respect to the support Show complete solution with fbd A 30 N-m 200 mm B 80 N-m 20 N-m 800 mm 600 mm
= BA The solid steel shaft carries the torques T₁ 750 N-m and T₂ 1200 N-m. Using L₁ L2 2.5 m and G-83 GPa, determine the smallest allowable diameter of the shaft if the shear stress is limited to 60 MPa and the angle of rotation of the free end is not to exceed 40. (Hint: Analyze for 0 governs and T governs). Odmin 54.1 mm = Odmin 46.7 mm B Odmin = 51.9 mm Odmin 26.0 mm 7₁ B C 1₂
Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP
Determine the maximum tensile and compressive bending stresses developed in the beam shown. The cross-section has the given properties. NA 1-35 x 10mm a. RA = b. RE= c. fb(c) = d. fb(T) = 80 mm 200 mm A 1.5m kN KN 5kN m MPa MPa B 1.5m SkN/m 2m 5KN n 2m 4
Q3. Two steel plates (A572, Fb = 50ksi) are welded together to form an inverted T-beam. Determine the maximum bending stress developed. ( %3D | 10 Marks) 10k 15 k 6ft 5 ft 10 ft 5 ft A B 8ft 1ft
Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
The shown L-shape cantilver is loaded as shown and fixed at A. It has a constant section of 40 mm X 20 mm. For point I located at 50 mm from support A, at the midheight of the section, determine the principal stresses, the principal planes and the maximum shear stress. y 50 mm 150 mm 40 mm 0.5 kN H- I 20 mm 3 kN 160 mm 2.5 kN
10. The hoisting beam assembly shown is supported by two 20- mm-diameter bolts at A and a 150 mm x 200 mm plate at B. In this problem, a = 1.2 m and b = 2.8 m. If the allowable tensile stress of the bolts at A is 112 MPa, which of the following gives the maximum safe value of W in KN? A. 45 C. 30 B. 60 D. 15 ZEIT 0 a BEEN H 8804 pe (cAPlate B to tried man 11 of 1911 b bell 110 mb llame lis To 102 W 20-102 bugil noitsuta
E oth ends of the steel shaft are attached to rigid supports. Find the distance a where the torque T must e applied so that the reactive torques at A and B are equal. 2 0.75d B T a A.
The shaft consisting of steel and aluminum segments carries the torques T and 3T. Find the largest allowable value of Tif the working shear stresses are 14 000 psi for steel and 7000 psi for aluminum, and the angle of rotation at the free end must not exceed 8°. Use G= 12 x 10° psi for steel and G=4x 10° psi for aluminum. Aluminum 1 in. 2T 3 ft. Steel 2 in. 3 ft.