The rigid bars AB and CD shown in Fig. are supported by pins at A and C and the two rods. Determine the maximum force P that can be applied if the movement of (P) is limited to 10 mm. Neglect the wieghts of all members.
Q: A 2000 kg load is applied to a steel bar of cross-sectional area 6 cm². When the same load is…
A: Load on steel bar and aluminum bar, M=2000 kgCross-sectional area of steel bar, As=6 cm2=6*10-4…
Q: Deep groove ball bearings are most widely used bearing type and suitable for many different…
A: (a) Write the given data. Fa=2 kNFr=5 kNNinner ring=400 rev/minD=30 mm Write the values of C10 and…
Q: For roboticists, electronic abilities are essential to success.
A: Please find the solution below
Q: 4.1) There is a real thermal engine that has an absorbed heat (Q1) of 5 kJ, the temperature of the…
A: Introduction: Heat engines are designed to generate usable work from the heat generated by the…
Q: Need help with this Mechanics of Materials review How to draw the element with the numbers (c)…
A: Given
Q: A flat belt is required to transmit 35 kW from a pulley of 1.5 m effective diameter running at 300…
A: Given data: Power transmitted by the belt (P) = 35 kW Effective diameter of the pulley (d) =1.5 m…
Q: QI\ Consider a woman standing on the earth with the sun directly overhead. Determine the ratio Res…
A:
Q: Aluminium alloys find use in aircraft industry because of (A) good weldability B) low specific…
A: Aluminium alloys find use in aircraft industry because of Answer: (B) low specific gravity
Q: A dead weight tester is a device commonly used for calibrating pressure gauges. Weight loaded into…
A:
Q: Q4: Compute the supplied heat (Q1) of a system that its thermal efficiency is 90%, and the work done…
A: Given data, Work done W= 173 J Heat input Q1 Efficiency e= 90%=0.9
Q: Velocity analysis of Scotch Yoke Mechanism 2. What is the effect of change in crank length and…
A: we have to determine the effect of change in crank length and angular velocity on the velocity v/s…
Q: Q2: A two-stroke diesel engine was electrically motored (non-firing operation) when the meter…
A: Given Brake torque, T = 120 N.m Speed, N = 600 rpm Calorific value, CV = 40.3…
Q: The door has a mass of m and a center of gravity at G. The door is pushed on with a force F at…
A:
Q: The five-bolt connection must support an applied load of P = 3800 lb. If the average shear stress in…
A:
Q: For the truss and loading shown, determine most economical cross-sectional area (in in2) of member…
A:
Q: 404-70-103=231 isn't it?
A: Given data: Net work is given and total heat supplied is given. The overall efficiency should be…
Q: The position x of a particle varies with time as x = at²-bt³. The acceleration of particle is zero…
A: As given in question, Position x of a particle as a function of time = x = a t2 - b t3 When given…
Q: As a design engineer you were ask to identify material(s) for cooking pot handle (Figure Q11). The…
A: Given question: We have to find a material for a handle that will not allow heat to flow through it.…
Q: Q3: A small sphere, rolling with an initial velocity of 9 m/s, moving up a plane inclined 30° with…
A:
Q: E.3) There is a steam system in which the boiler must be fed by using a pump that supplies 0.005…
A:
Q: members DE, DJ, EJ, and IJ. 2 KN XNK 8m 8m 8m 8m L K J H 1 kN 8m 3 KN 1.5m 2m 8m
A: To find force in member DE,DJ,EJIJ
Q: Mex 02: A turbocharged diesel engine has an exhaust gas flow rate of 0.15 kg/s. The turbine T P₁ T P…
A:
Q: The car A has a forward speed of 21 km/h and is accelerating at 3.0 m/s². Determine the velocity and…
A:
Q: 01- Draw the wind turbine power curve characteristics and discuss the regions of the curve. What is…
A: given; draw wind turbine power curve chracterstcis?power coefficient(Cp)=1627wind power(P)=100kwwind…
Q: 2/92 The force F has a magnitude of 300 lb and acts along the diagonal of the parallelepiped as…
A:
Q: What happens when stress exceeds stra O The material will go back to normal O The material will stay…
A: When the stress exceeds the strain the material beguns to yield permanently and at last the material…
Q: Q4: The power output of a six-cylinder four-stroke engine is absorbed by a hydraulic WN dynamometer…
A: Given data: Engine type = four stroke Number of cylinder = k = 6 Power output of engine i.e. brake…
Q: 02: A two-stroke diesel engine was electrically motored (non-firing operation) when the meter…
A: Given Brake torque, T = 120 N.m Speed, N = 600 rpm Calorific value, CV = 40.3…
Q: A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress…
A: calculate the magnitude of the bending stress (in Pa) at a point 23 mm from the top of the beam on a…
Q: WN 20000 Q4: The power output of a six-cylinder four-stroke engine is absorbed by a hydraulic…
A:
Q: 2: A: A 3 Kg mass of a small train (game) moves in an acceleration of 0.9 m/s2. Compute the work…
A:
Q: The slider P can be moved inward by means of the string S, while the slotted arm rotates about point…
A:
Q: Determine the slope and the displacement of the beam at the end of C. A is pin and B is rolle El is…
A:
Q: A strip of rubber originally 75 mm long is stretched until it is 100 mm long. What is the tensile…
A:
Q: Calculate the gas pressure, of air density is 1.22 Kg/m3, L-200 mm * Patm Gas at pressure p Tank…
A: Given:- L = 200 mm = 0.2 m Air density = 1.22 kg/m3 To Find:- Gas Pressure (P)
Q: HOME WORK 1. Calculate the maximum and minimum limits for both the shaft and hole in the following;…
A: Given: Let us consider the given data, a) 45H8/d7b) 180H7/n6c) 120H7/s6d) 40G7/h6e) 35C11/h10 To…
Q: Two vectors have magnitudes 2m and 3m. The angle between them is 60°. Find the magnitude of their…
A: From the data given in the question, The magnitude of one of the vectors = a → = 2 m The magnitude…
Q: The performance of a structural element is determined by the properties of the material the geometry…
A: Explanation: The performance of structural element is determined by: 1.Material Properties like…
Q: A(1/5) scale model automobile is tested in a wind tunnel with the same air properties as the…
A:
Q: Find out area - moment of inertia of a triangular lamina of base b and heigt h about an axis passing…
A: here, b is the base of the triangle h is the height of triangle C is the centroid of the triangle…
Q: T T P 02: A turbocharged diesel engine has an exhaust gas flow rate of 0.15 kg/s. The turbine P.…
A:
Q: ________distinguises the system from the surroundings. a. boundary b control surface c. control…
A: ________distinguises the system from the surroundings. Answer: a. boundary
Q: Q2: The lecturer Aous used to drive his car early inorder to arrive and teach his students some…
A: The time that he should start driving from Baghdad: 7 : 10 a.m.
Q: Find the efficiency of a diesel cycle with an explosion energy of 3000 J/mol. Air is introduced into…
A:
Q: Determine the magnitude of the vertical force Cy for the simply supported beam, where w = 8 kips/ft,…
A: given data; w=80kips/ftM=270Kip-ftAB=L1=12ftBC=L2=3ftCD=L3=7ft lets take reaction force at A=RAlets…
Q: Consider two long, slender rods of the same diameter but different materials. One end of each rod is…
A:
Q: 2 A truss is loaded with various forces of magnitudes as shown in Fig. 2. Determine the forces in…
A: To find force in member DE,DJ,EJ,IJ
Q: Two steel springs arranged as shown support a load P. The left spring consists of 12 turns of 20-mm…
A:
Q: = Q2: A 1.78 L four-stroke petrol engine was tested at 2500 rpm. The developed brake power is 28 kW…
A: Given Volume, V= 1.78 L = 0.00178 m3 Brake power, BP = 28 kW Speed, N = 2500 rpm…
Step by step
Solved in 2 steps with 2 images
- The rigid bars AB and CD shown in Fig. are supported by pins at A and C and the two rods. Determine the maximum force P that can be applied if the movement of (P) is limited to 10 mm. Neglect the wieghts of all members. Aluminum L = 2 m A = 500 mm² E = 70 GPa A 3 m 3 m 3 m 0 P 3m B Steel L= 2 m A = 300 mm² E = 200 GPa D P = 153 KN P = 133 KN P = 113 KN P = 103 kN OThe uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.600 N 0.4 m 0.4 m -03 m-03 m-03 m-03 m- The frame shown is supported by fixed support at E and smooth surface at A. Find: • the internal forces exerted by the internal Pin at B. Bx=.. ByD • The internal force at D
- The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap D= 4 mm between the lower end of the left rod and its pin support at C. Compute the stress in the left rod after its lower end is attached to the support. The cross-sectional areas are 300 mm2 for rod AC and 250 mm2 for rod BD. Use E= 200 GPa for steel. lo/0 0.75 m 1.5m 2 m ANSWER: MPaAxial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F1 = 31 kips, F2 = 13 kips, F3 = 24 kips, and F4 = 37 kips, determine the absolute value of the axial load in rod (2).Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 31 kips, F₂ = 11 kips, F3 = 22 kips, and F4 = 36 kips, determine the absolute value of the axial load in rod (2). F A F₂ (1) F₂ B F3 C (3) D O 16 kips O 12 kips O 7 kips O 9 kips O 22 kips
- The force on a wagon wheel is F=2000 N. Find the axle diameter of the wagon wheel made of Fe50 material. Given: GAK=2900 daN/cm2, S=2 F/2 F/2 a=70Snap fits are commonly used to lock plastic parts together. A design for a torsional snap- fit is shown. The rod ABC is fixed at both ends and a tab is attached to the rod pivots under the action of forces shown. The rod diameter is 7mm and G-4 GPa. Treat the tabs as rigid. Li-60mm, L2-40mm, w-30mm. (a) Determine the rotation of the cross-section B and the displacement of end D if the force F-8N. (b) Determine the maximum shear stress in the rod (Note: the latter two diagrams are to help you conceptualize.) DE W В THE F Tc ТА A TоQuestion 1: Given that Tuitow = 50 MPa for the rod AB and tattow = 25 MPa for the rod BC. If T=1250 N.m, find the required radius for both rods. Ahmtmum AB = BC =
- plz help before -ront The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T₁ 410-N forces act in the - direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and components of force on the shaft. Figure lashel but sol is 300 mm A 200 mm 2 150 mm 150 mm ✓ 200 mm 400 mm B. 200 N 200 N 80 N 80 N 1 of 1 ▾ Part B Determine the resultant shear force in the y direction on the cross section at C Express your answer to three significant figures and include appropriate units. (Vc)y=245.714 Submit Part C Submit * Incorrect; Try Again; 3 attempts remaining Check your signs. (Vc),= 175 ▾ Part D Determine the resultant shear force in the direction on the cross section at C. Express your answer to three significant figures and include appropriate unite. T= 10 ▾ Part E Previous Answere (Mc) Submit M ^ Part Fi * Incorrect; Try Again; 5 attempts remaining…A safety valve spring having 9 and 2 coils has the ends squared and ground. The outside diameter of the coil is 115 mm and the wire is 13 mm. It has a free length of 203 mm. The length of which this spring must be initially compressed to hold a boiler pressure of 1.38 MPa on the seat of 32 mm diameter. Modulus of rigidity is taken as G=80GN/m?. a. Find the force acting on the valve set. b. Determine the mean diameter c. Determine the spring index d. Find the spring deflection e. Find the operating length f. Calculate the solid length g. Calculate the deflection of solid length h. Compute the solid force i. Compute the Wahl factorRope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of ø = 64.0 ° with the floor and rope segment CD creates an angle 0 with the horizontal. If both ropes BCA and CD can support a maximum tensile force Tmaz = 165 lb. what is the maximum weight Wmar of the crate that the system can support? What is the angle e required for equilibrium? Express your answers numerically in pounds and degrees to three significant figures separated by a comma. • View Available Hint(s) nν ΑΣφ vec Wmax.0 = lb, degrees