Answered: the resistance of the ship in sea…

Engineering

Mechanical Engineering

the resistance of the ship in sea water. The

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.13P: 5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its...

See similar textbooks

Related questions

Q: The figure belows shows a closed tank holding air and oil to which is connected a U-tube mercury…

Q: 2. Block A weighs 100N and block B weighs 300N both rests on an inclined plane downward to the right…

A: Here I am going to find the tension in the cable due to the blocks on inclined plane.

Q: A student living in a 4-m x 6-m x 6-m dormitory room turns his 150-W fan on before she leaves her…

A: Data available:Pressure inside the room is 100 kPa,P=100 kPaTemperature inside the room is 15o…

Q: In July of 2020, NASA launched a rover to Mars called Perseverance. The mass of the rover when…

Q: A ventilating fan of the bathroom of a building has a volume flow rate of 25 L/s and runs…

A: GivenQ=25L/s =25×10-3 m3/sρ=1.60 kg/m3time t =1day

Q: The bore on a cylinder of a compressor is 2 inches. The stroke is 3 inches.What is the displacement…

A: Compressor Displacement is defined as the volume swept by the piston. during the revolution of…

Q: aluminum alloy 2014

A: Problem asked to specify a practical heat treatment for a 2014 aluminum alloy that will produce a…

Q: 1. Consider the following diagram. The fluid flowing in the pipe is oil (SG = 0.830). The fluid in…

Q: The maximum lift-to-drag ratio of a 600,000 lb aircraft is 18.7. The Thrust Specific Fuel…

A: Initial weight= 600000lb Fuel weight= 180000lb TSFC= 0.85 (lb/hr)/lb To find maximum endurance of…

Q: The car moves in a straight line such that for a short time its velocity is defined by v = (312+ 2t)…

Q: A capillary tube is immersed vertically in a water container. Knowing that water starts to evaporate…

Q: The air in an automobile tire with a volume of 2.60 ft3 is at 70°F and 22 psig. Determine the amount…

Q: Problem A 104.37 kg mass has a potential energy of -45,600.00 joules with respect to a given datum…

A: Given data: ● Mass: m = 104.37 kg ● Potential energy: P.E. = -45600 Joule Required: (a) The height…

Q: A centrifugal pump discharging 10 lps against 25 m of head and operating with an efficiency of 60%…

Q: Problem 2 Determine the components of the force along lines a and b. Apply the parallelogram law.…

Q: Shown is the stress-strain curve developed from the tension test of a metal alloy bar. The specimen…

Q: Solve with the correct unit 4. A cylindrical tank is 50 in. long, as a diameter of 16 in.and…

Q: , Describe: a. One situation when the kinetic energy term for a turbine is negligible. b. One…

A: There are two situations where we can neglect the kinetic energy and on the other side we can not…

Q: A fireworks show is choreographed to have two shells cross paths at a height of 103 feet and explode…

Q: An uninsulated 100-mm diameter steam pipe runs for 25-meters inside a room whose walls and air are…

Q: Find the depth of liquid in Reservoir (B) so that the circular gate just starts to open. The gate is…

A: Given: The thickness of gate, t = 3 mm

Q: Three particles of mass m, 4m and 4m are constrained to move along a frictionless horizontal groove.…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: #3/ 1516 13 16 1016 15. 48 63 126 2516 74 31b Find R+O

Q: Q-A hollow rectangular masonry pier 600 mm x 900 mm and 150 mm thick transmits a vertical load of…

Q: the Reynolds number i

A: Reynolds number is the ratio of inertia force to viscous force and it is used identify the type of…

Q: 2.51 Two forces P and Q are applied as shown to an aircraft connection. Knowing that the connection…

A: Given:P=600 lbQ=800 lb

Q: A hollow shaft is subjected to a maximum torque of 1.5 kN-m and a maximum bending moment of 3 kN-m.…

Q: Determine the velocity in the discharge side. Determine the velocity on the suction side. Determine…

Q: sultant of the system is 75000 N-mm counter-clockwise couple determine P, and C. 51 y 12 A 100 N n C

Q: A camera tripod is set up as shown below. The tripod is pretty fancy and has self-balancing legs.…

Q: A projectile is launched from point A with speed vo= 35 m/s. Determine the value of the launch angle…

A: Given Velocity, vo = 35 m/s Height, y = 12 m Find Distance, R Angle

Q: Using a FBD of the beam, assuming members in tension, relate the force in the members and the…

Q: Plot and determine the values of h5, W5, twb5 & tdb5 involving adiabatic mixing as shown below. Air…

A: Given: State 1: 15 C DBT and 90% RH flowing at 10 kg da/s State 2: 24 C DBT and 60% RH flowing at…

Q: Supposing two liquids of different densities ρ=1750 kg/m3 and ρ=500 kg/m3 were poured together…

Q: 28 cm a? 100 cm 30° V 15 cm

Q: The force P applied at the handle of the rigid lever shown in Fig. 4 causes the lever to rotate…

Q: Check to see if the golf ball clears the tree at A. Calculate the height h above the ground when the…

A: Given: V0 = 118 mi/hr θ=19.44o To find: Calculate the height h above the ground when the ball passes…

Q: A 5m copper tube is heated externally to 100degC. Air is heated by passing it through the 40mm…

A: Given Temperature, T1 = 100oC Inlet temperature, Ti = 20 oC Exit temperature, Te = 88 oC Diameter, d…

Q: A time harmonic force f(t) = (6-j8) e^jot N produces a displacement of X(t) = (2+j5) e^jot Calculate…

A: Given data, Harmonic force, Ft=6-8jejωt Displacement, xt=2+5jejωt To determine, the ratio between…

Q: 2. Block A weighs 100N and block B weighs 300N both rests on an inclined plane downward to the right…

A: Here I am going to compute tensions in cable.

Q: Solve with the correct units 7. Two liquids of different densities(p1=1500 kg/m3 and p2=500 kg/m3)…

Q: The air in a house is at 19°C, 59% relative humidity, and total pressure 89kPa. If air is cooled at…

Q: * Properties of Saturated H₂O мра Vf 1 1.1 1.2 0.001127 (2) 0.001139 Va 0.1944 (?) 0.1633

Q: 2. (a) Find the resultant of these three forces in vector form. (b) Find the magnitude of part (a)…

Q: determine the magnitude of the forces F1, F2, and F3 that keeps the particle in balance.

A: Write the force vector F1. F1=F145j+F135k

Q: determine the magnitude of the forces F1, F2, and F3 that keeps the particle in balance.

Q: An aluminum-alloy rod has a length of 9.9269 cm at 30.00°C and a length of 9.9686 cm at the boiling…

Q: 2.34 Determine the resultant of the three forces of Prob. 2.22.

Q: A composite plane wall consists of a 5-in.-thick layer of insulation (ks = 0.029 Btu/h ft. "R) and a…

Q: Given the top and front views, sketch the right face

A: According to the details provided in the question we need to draw right hand side view of the given…

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

A ship 350 m long moves in sea water whose density is 1030 kg/m3 . A 1:120 model of this ship is to be tested in a wind tunnel. The velocity of the wind tunnel around the model is 35 m/s and the resistance of the model is 65 N. Determine the velocity and also the resistance of the ship in sea water. The density of air is given as 1.24 kg/m3 . Take the kinematic viscosity of air and sea water as 0.012 stokes and 0.018 stokes respectively.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given-Information:-

VIEW

Step 2

VIEW

Step 3

VIEW

Step 4 Final-Answer:-

VIEW

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

We want to predict the drag force on a remote-control airplane as it flies through air having a density of 1.21 kg/m³ and a viscosity of 1.76x10- Pa-s. The airplane's fuselage has a diameter of 200 mm and the airplane will fly through air at a speed of 32 m/s. A model of the airplane's fuselage will be tested in a pressurized wind tunnel. The diameter of the model is 75 mm and the density and viscosity of the air in the wind tunnel are 3.00 kg/m³ and 1.82× 10-5 Pa-s, respectively. a) The diameter of the airplane's fuselage will be used to define the Reynolds number Re, for the flow around the fuselage. Compute the Reynolds number for the flow around the airplane's fuselage (answer: Re, = 4.40x 10'). b) Find the speed of the air that should be used to test a model of the fuselage in the wind tunnel to correctly model dynamic conditions (answer: 35.6 m/s). c) The model is tested in the wind tunnel at four speeds that bracket the speed computed above. The measured drag forces on the…
The sketch shows an oil manometer that is connected between two pipes which transport water. The density of water can be taken as 998kg/m3, the specific gravity of glycerol is 0.76 and atmospheric pressure is 100 kPa. The respective dimensions (as shown on the sketch) are given below: h1 = 0.17 m h2 = 350 mm h3 =15cm. From the given data, calculate the pressure difference between the two pipes.
A bullet is to be tested in the laboratory to determine the drag force on it. Dependent parameter the drag force D (Newton) depends on the velocity of the bullet V(m/s), the length of the bullet L(m), sound velocity c(m/s), density of fluid ρ (kg/m3) and dynamic viscosity µ(kg/ms). Solve the problem by making the necessary assumptions and drawing the schematic figure. I-Determine the nondimensional p parameters using repeating variables ii-a bullet with a speed of 96,2 m/s in air may be modelled in a water tunnel with a test section velocity of 262 cm/s. Determine the length of the model, if the length of the bullet is 56,2 mm. The air and water temperature is 20 oC degree at 1 atm. iii- if the drag force on the model is measured to be 2,62 N, then determine the expected drag force on the bullet. Comment on dynamic similarity equivalence?
A ship is 35 m long and is designed to move at 11 m/s. Laboratory experiments are carried out in a water tank with a 1 m long model. Find the velocity and the ratio of the resistive forces of the model. (r=1000 kg/m3)
Global warming will produce rising sea levels partly due to melting ice caps and partly due to the expansion of water as average ocean temperatures rise. To get some idea of the size of this effect, calculate the change in length, Ah (in mm), of a column of water 1.5 km high for a temperature increase of 1.2 °C.Assume the column is not free to expand sideways. As a model of the ocean, that is a reasonable approximation, as only parts of the ocean very close to the surface can expand sideways onto land, and only to a limited degree. As another approximation, neglect the fact that ocean warming is not uniform with depth. Properties of water: 3 = 210 x 10 /C. c= 4186 J/kg - °C, L; = 334 kJ/kg, Le = 2256 kJ/kg Enter you answer below (to the nearest mm): Ah (in mm) = Type your answer.
The property of a fluid called viscosity is related to its internal friction and resistance to being deformed. The viscosity of water, for instance, is less than that of molasses and honey, just as the viscosity of light motor oil is less than that of grease. A unit used in mechanical engineering to describe viscosity is called the poise, named after the physiologist Jean Louis Poiseuille, who performed early experiments in fluid mechanics. The unit is defined by 1 poise = 0.1 (N s)/m2. Show that 1 poise is also equivalent to 1 g/(cm · s). %3D
1)The model of the torpedo (a military vehicle that goes very fast underwater) as placed in a tank is moved by being towed at a speed of 14,4 m/s. In the prototype, the torpedo is expected to move at a speed of 4.2 m/s in water at 15°C. The kinematic viscosity of water at the same temperature is v=3.4x10^(-3) m2/s. a) Determine the scale of the model used. b) If the same prototype and the torpedo model, prepared in the same size, is moved in a wind tunnel where u air=1.975x10^(-4) Ns/m2 and p air=22.5 kg/m3 air with physical properties under 10 atmospheres pressure and 26 C° constant temperature are used. What is the speed of the torpedo?
A plate 0.05mm distance from a fixed plate moves at 1.25 m/s and required a force per unit area of 3 Pa to maintain this speed by using an oil of specific gravity 0.65. Find the dynamic viscosity in centipoise and kinematic viscosity in stokes of the fluid between the plates. Calculate the specific weight in kN/m³, density, and the specific gravity of a liquid having a volume of 662900 cm and weight of 55 kN
The kinematic viscosity of liquid oil is 20 stoke and relative density = 0.85. Find the dynamic viscosity of this liquid oil in Sl and British systems. (1 stoke = 1 cm/s, 1m 3.28 ft, 1ft 30.48 cm and 1kg = 2.2 lb). Choose the correct answer: a- In SI system 25 kg/m.s and in British system 16.6 Ib/ft.s b- In SI System 17 kg/m.s and in British system 1.17 Ib/ft.s c- In Sl system 20 kg/m.s and in British system 8.15 Ib/ft.s
The drag force on a submarine, which is moving on the surface, is to be determined by a test on a model which is scaled down to one-twentieth of the prototype. The test is to be carried in a towing tank, where the model submarine is moved along a channel of liquid. The density and the kinematic viscosity of the seawater are 1010 kg/m³ and 1.3x10-6 m 2/s, respectively. The speed of the prototype is 2.6 m/s. Assume that F = f(V, L. g. p.), using pi-theorem and similarity principle to: a) Determine the speed at which the model should be moved in the towing tank. b) Determine the kinematic viscosity of the liquid that should be used in the towing tank.
The sliding plate viscometer shown below is used to measure the viscosity of a fluid. The top plate is moving to the right with a constant velocity of 10 m s in response to a force of 3 N. The bottom plate is stationary. What is the viscosity of the fluid? Assume a linear velocity distribution.
The thrust force, F generated by a propeller is found to depend on the followingparameters: diameter D, forward velocity u, density ρ, viscosity µ and rotationalspeed N. Determine the dimensionless parameters to correlate the phenomenon