51%P 9:31KOREK I.www.bartleby.com= bartlebyQ&A Sign inEngineering / Electrical Engineeri... / Q&A Libr... /The resistance of the filed coils wit...QuestionThe resistance of the filed coils with copper conductors of adynamo is 120 N at 25°C. After working for 6 hours on full load,the resistance of the coil increases to 140 2. Calculate the meanlempetature tive of the fieid coil. Take the tempetatute coefficientuf the comductor material as 0.0042 at 0C.V Expert Answer>

We known that resistance is changed as the temperature is changed so that value of resistance is…

The resistance of the filed coils with copper conductors of a dynamo is 120 2 at 25°C. After working for 6 hours on full load, the resistance of the coil increases to 140 2 Calculate the mean lemporature tive of the fieid coil. Take the tempetatute coefficient Hf the conductr musterial as 0.0042 at 0'C.

The resistance of the filed coils with copper conductors of a dynamo is 120 2 at 25°C. After working for 6 hours on full load, the resistance of the coil increases to 140 2 Calculate the mean lemporature tive of the fieid coil. Take the tempetatute coefficient Hf the conductr musterial as 0.0042 at 0'C.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q.4/ choose true or false: 1. The reluctance of any core is proportional directly with the length of it and inversely with both the permeability and the cross-section area of it. 2. The number of parallel paths in wave windings is equal to twice of the number of poles. 3. In dc machines with same values of Z, N, Ø, the emf for wave winding type is more than emf of lab winding type. 4. If we insert a current in such a conductor subjected to a constant magnetic field, a movement will achieved giving the principle of electric generator.
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following:a. Circulating currentb. Voltage across the resistorc. Voltage across the capacitord. Real power supplied by the source
A 500-turn coil is wound on an iron core. When a 120-V-rms 60-Hz voltage is applied to the coil, the current is 1 A rms. Neglect the resistance of the coil. Determine the reluctance of the core. Given that the cross-sectional area of the core is 5 cm2 and the length is 20 cm, determine the relative permeability of the core material.
What will happen to the value of the impedance if the resistance will be increased or decreased? Explain...
Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The average load voltage with and without FWD and discusses these cases. 2-lf firing angle equal to 45°, the supply voltage is240v, transformer ratio is (2/1). Calculate the DC current& voltage of this case. 3- Draw all waveforms diagram. 4- what are the difference between the type of connection (Delta or Star).
In order to obtain a highly links between two winding's, the coupling coefficient will be equal to . . of its maximum value. * .... ..... Twice One half Less than half More than half
A triac can pass a portion of …………… half-cycle through the load a. neither positive nor negative b. both positive and negative c. only negative d. only positive
5- The most effective factor on the leakage inductance of an iron-cored coil is: a) The geometry of the coil. b) The current passing through it. c) The frequency of the applied voltage. 6- The iron losses is constant in power transformer because: a) The frequency is constant. b) The flux density is constant. c) The voltage is constant. 7- One of the reasons leads to prefer the core type transformer more than the shell type is:
The physical construction of two pairs of magnetically coupled coils is shown. Assume that the magnetic flux is confined to the core material in each structure. Show two possible locations for the dot markings on each pair of coils.
12 - How to calculate the impedance of a coil?A) It is the difference between ohmic resistance and inductive resistance.B) It is the ratio of ohmic resistance to inductive resistance.C) It is the vectorial sum of ohmic and inductive resistance.D) It is the algebraic sum of ohmic and inductive resistance.E) It is the ratio of inductive resistance to ohmic resistance.
Q-3 A Cockeroft-Walton type voltage multiplier has ten stages with capacitances, all equal to 0.1 µF. The supply transformer secondary voltage is 100 kV at a frequency of 60 Hz. If the load current to be supplied is 5 mA, find (a) the percentage ripple, (b) the regulation, and (c) the optimum number of stages for minimum regulation or voltage drop.
The resistance of the copper field winding of a dc machine at 40 degree Celsius is 0.40 ohms. After operating for some time, the resistance is found to be 0.50 ohms. Find the operating temperature.