The RC circuit shown in the figure has resistance of R=7k2 and the capacitance of C=10µF. The capacitor is initially charged and at a voltage Vo=20V at t=0, when the switch is closed. How long does it take the capacitor to discharge to 33% of its initial charge? Express your answer in units of ms (milliseconds)using one decimal place. = Vo R

The RC circuit shown in the figure has resistance of R=7k2 and the capacitance of C=10µF. The capacitor is initially charged and at a voltage Vo=20V at t=0, when the switch is closed. How long does it take the capacitor to discharge to 33% of its initial charge? Express your answer in units of ms (milliseconds)using one decimal place. = Vo R

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Consider the circuit shown in the figure below. The four capacitors have capacitances C1=15μF, C2=16μF, C3=19μF, C4=13μF and are connected to a battery of voltage V=39Volts. When all capacitors are fully charged, determine the voltage across C4. Express your answer in units of Volts using one decimal place.
In the schematic below two batteries are in series and drive current through the circuit as shown. The first resistor has a voltage drop AV₁ = 1.2 V, the middle resistor has a resistance of R = 64, and the last resistor has a voltage drop AV₂ = 1 V. Given these parameters, what is the magnitude of current flowing through the circuit in milli-amps (mA)? Giver your answer to 3 significant figures. AV, ww 3.0 V 4.5 V ww ΔV, ww R
Consider the following circuit diagram. The potential difference across the battery is 40.0 volts, and it supplies a current of 5.00 amperes to the circuit. There is a current of of 2.70 amperes flowing through R1. Resistor R2 has a resistance of 5.50 ohms. What is the resistance of R3? Answer in ohms to two decimal places, but do not include units in your answer.
A set of current (I) and voltage (V) data is collected for a given circuit. The current is measured in mA and the voltage is measured in volts. If you plot a graph of I vs. V, what are the units on the slope? 1 kQ mV A mA V.s C V.s
Consider the circuit shown in the figure below. The four capacitors have capacitances C1=10μF, C2=13μF, C3=77μF, C4=19μF and are connected to a battery of voltage V=46Volts. When all capacitors are fully charged, determine the charge on C4. Express your answer in units of μF using zero decimal places.
An electrical circuit contains a capacitor of 52 picofarads and a resistor of 1344 ohms. If the capacitor is fully charged, and then the voltage is interrupted, in how much time will about 95% of its charge be transferred to the resistor?
Use E, C,t,R as variables and "*" for multiplication,"/"for division. And use brackets where necessary. exp (-a)should be written as e^(-a) Given the resistance R and capacitance C of an RC circuit,we apply an emf of E volts. What is the maximam charge that can be stored in the capacitor. After completing the circuit we wait for t seconds. What is the stored charge now?.
For the circuit shown above, the emf of the batteries and the resistances are listed below. ℰ1 = 48 V, ℰ2 = 7 V, R1 = 13 Ω, R2 = 5 Ω , R3 = 16 Ω. Determine I1=? Please express your answer in units of Amperes (A) with two decimal places. If you a find a negative value, please don't forget the minus sign.
The resistance R1 = 10 OHM and R2 = 25 OHM are one after another (in seri) in a circuit. What is the total resistance of R1 and R2?
In the circuit in (Figure 1) the voltage and current expressions are v = 36e 25t V, t≥ 0; i = 12e 25 mA, Figure C t≥0¹. + VR T 1 of 1 Part A Find R. Express your answer to three significant figures and include the appropriate units. ► View Available Hint(s) R = Submit Part B μÅ Value Units ? Find C. Express your answer to three significant figures and include the appropriate units. ► View Available Hint(s)
Two resistors are connected in parallel with an 96 volt battery. The resistors have values of R1 = 14 ohms and R2 = 96 ohms. What is the current in amperes for this circuit? Round your answer to two decimal places.
An electrical device draws 3.4 A (amps) when a voltmeter shows a voltage drop of 5.6 V (volts) across it. What is the electrical resistance of the device? Give your answer to the nearest tenth (0.1) ohm. Do NOT give units in the answer (since the units are already specified). Your Answer: Answer