The process diagram of a binary power plant with an ORC-process, utilizinggeothermal energy, is presented in figure 1 below. Generator efficiency is 94%, generator outputpower is 180 kW and evaporator heat power is 2590 kW. Calculate the turbine output power.Round off your answer to one an integer.Heat intoprocessEvaporatorTurbineGFeed pumpFigure 1. Process diagram of the binary power plant.GeneratorCondenser

Turbine output power=191.48 KWExplanation:Step 1: Step 2: Step 3: Step 4:

Answered: The process diagram of a binary power…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Explain binary cycle power plant (using figure). Compare its performance as compared to other geo-thermal power plants.
How do generators and transformers contribute to voltage regulation in a power system?
1.List the three steps of nuclear fuel fabrication processes. Also sketch a schematic diagram and label the processes on the diagram. 2 What is geothermal energy? With the aid of a schematic diagram, describe how we can generate electricity using a geothermal energy-driven dry steam power plant. 3.Discuss the differences between Pelton, Francis, and Kaplan turbines.
Write down construction of an alternator with help of diagram and write its principle of operation. Subject is Electrical Machines.
3. Two de generators each having linear characteristics that operate in parallel. One machine has a terminal voltage of 470V at no load and 220 V at a load current of 100A. while the other machine has a voltage of 480 V at no load and 200 V at 120 A. calculate the current in each generator and the bus bar voltage when the total load is 200A. What is the kilowatt output of each machine under this condition?
help me in these questions pls write the questions with the and by (Computer) 1-Which of the following statements INCORRECTLY explain the label in the figure about LVDT working principles? a. Secondary coils are connected in series in such a way that their output is opposing each other. b. Constant DC voltage input to primary coil. c. Displacement moves ferrous rod from central position. d. The difference of the output voltage between the two secondary voltage.==========2- Explain the working principle of the measurement system in the figure below.i. Force input that is supplied to the sensor is processed to give the response in the form of raw output signal.ii. Signal conditioner manipulated the weak signal to give a conditioned input.iii. Analog or digital indicator display the unit that gives output reading of quantity being measured.iv. Measured value is compared with the input value for further action. a. ii, iii and iv only. b. i, ii and iv only. c. i, ii and…
Two 50-MVA, 3-phase alternators operate in parallel. The settings of the governors are such that the rise in speed from full-load to no-load is 2 percent in one machine and 3 percent in the other, the characteristics being straight lines in both cases. If each machine is fully loaded when the total load is 100 MW, what would be the load on each machine when the total load is 60 MW? (Req'd) Draw an appropriate diagram.
A 50-kW generator has a full-load efficiency of 90.5 percent. Determine the total losses. Ans.: 5,250 watts explain step by step, circuit diagram, principles etc and also write it clearly.
Two 60MVA, alternators operate in parallel. The setting of the governor are such that the rise in speed from full load to no load is 2% in one machine and 3% in the other, the characteristics being straight lines in both cases. If each machine is fully loaded when the total load is 120MW, what will be the load on the first machine (with 2% speed regulation) when the total load is reduced to 80MW?
Draw and explain a typical power curve for a wind turbine and write the definition of the four important terms that are shown in the power curve
Combination circuit what is PT? RT? IT? Voltage Across each load?
Maz a) A sinewave is having a frequency of 50 Hz and instantaneous value of 250 Volts at 1.3 milli seconds. Find D The maximum value of sinusoidal voltage waveform and i) The value of voltage at 2.1 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 10 milli seconds and 0 =40 degrees. on Vp Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximnum value = a) (ii) Value of voltage at 2.1 ms = b) Angular frequency =

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS