The position control system for a spacecraft plat- form is governed by the following equations: d²z dz + 2 + 4z = 0 %3D dt2 dt de = 0.6v2 dt vị = r – z v2 = 7v, %3D The variables involved are as follows: r(t) = desired platform position z(t) = actual platform positiom v:(t) = amplifier input voltage v2 (t) = amplifier output voltage %3D O(t) = motor shaft position Sketch a signal- flow diagram of the system, identifying the component parts and their transmittance; then determine the system transfer function Z(s) r(s)

The position control system for a spacecraft plat- form is governed by the following equations: d²z dz + 2 + 4z = 0 %3D dt2 dt de = 0.6v2 dt vị = r – z v2 = 7v, %3D The variables involved are as follows: r(t) = desired platform position z(t) = actual platform positiom v:(t) = amplifier input voltage v2 (t) = amplifier output voltage %3D O(t) = motor shaft position Sketch a signal- flow diagram of the system, identifying the component parts and their transmittance; then determine the system transfer function Z(s) r(s)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the signal flow graph of the given figure, consider the following statements 1. It has three forward paths 2. It has three individual loops 3. It has two non touching loops Out of above the correct statements are X2 X3
Q2:- By using IC 74151 Construct the following Function: F(A,B,C)= Eodd no.-1
For the signal flow graph of the ints given figure consider the following statements: 1. It has three forward paths. 2. It has three individual loops. 3.lt has two non touching loops. out of above the correct statements are X2 X3 О 2,3 O 1,2 O 1, 2, 3 О 1,3
about nyquist stability criterion in deatials
The transfer function of an LVDT is 2 mV/mm and the maximum core motion is +14 cm. From +1 cm to +12.5 cm, the LVDT can track work-piece motion. Determine the output voltage range of the LVDT.
Signal and system problem plz explain every step how do this step
Vcc=15V Q1: BC237 Rc 3.6kQ or BC238 B=200 VBE(on)=0.7V R1 110KQ Rs Cci 1000 4.7µF Cco 4.7µF R2 ·27kΩ RE 1.2kQ RL 12kΩ Vs Rin Rout Figure 1. Common-emitter amplifier. 2)
For the signal flow graph of the given figure, consider the following statements 1. It has three forward paths 2. It has three individual loops 3. It * has two non touching loops Out of above the correct statements are Xg 1,3 O 1, 2, 3 O 1,2 O 2, 3 O
Where and How Simplex, Half Duplex and Full Duplex Modes are used in Real Life? Explain withExamples and Diagrams
Frequency Response Discuss the importance of Nyquist plot technique in control systems.
What is equation of the demodulator? advantages and disadvantages of DSB-SC over DSB-AM?
Question: If you know the input voltage is 20 Vpp (top to top) and the load resistance is KN R=1 calculate what's coming.: 1- At the first approximation calculate (the greatest current passing through the load resistance, output voltage). 2- At the second approximation calculate (the greatest current passing through the load resistance, the output voltage . draw the shape of the output signal). 3- When rounding second guess (the greatest stream passes through the load resistance if you know that the current front 15 ml-amp at voltage of 1 volt, voltage output, draw the shape of the signal emerging). Sinusoidul Wavefom Supply Rectifed Output Waveform AA Diode No Negutive Halt cycle