The OP AMP controller shown regulates the output of a feedback system. It has the following component values: R₁ = 470 kW Rd=470 kW R₁ = 1.2 MW C = 4.7 mF Find the transfer function of this controller using the given values. 1) 1+221 1+1 105 2) 3) 0.7186+1.588 1+1.105 0.5+1.105 1-1.105 4) 1+221 1+1.569

The OP AMP controller shown regulates the output of a feedback system. It has the following component values: R₁ = 470 kW Rd=470 kW R₁ = 1.2 MW C = 4.7 mF Find the transfer function of this controller using the given values. 1) 1+221 1+1 105 2) 3) 0.7186+1.588 1+1.105 0.5+1.105 1-1.105 4) 1+221 1+1.569

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The term duty cycle refers to the amount of time a signal is complete cycle. A. off compared to the period of one B. on The output voltage of op-amp is positive saturation, when the voltage applied to the input is greater than the input. A. inverting B. noninverting A square wave that is 20V at its high state and OV when it is off will produce an average DC when its duty cycle is 75%. Formula: VOUT = Duty Cycle * Peak voltage voltage of A. 7.5V B. 10V C. 15V
1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
How can I add two voltages values together with on op amp? Using op amps, how to make an AD Converter? A DA Converter? What components determine the frequency of an astable, 555 oscillator? Draw the circuit. Draw a circuit for both an astable and a monostable, 555 multivibrator. What is the duty cycle and percentage duty cycle of a pulse train or square wave? What is the overshoot, rise time, fall time, and pulse width of a pulse and where on the waveform is each measured?
a square wave. stion 9 vet ered It is the average of the two dc currents that flows into the inverting and non- inverting inputs of an op-amp. d out of OInput Bias Current question O Input Offset Current O Quiescent Operating Current O Feedback Current For the op-amp circuit below, which of the following statements is true? Let Ad = 100,000 and + Vsat = + 5 V. %3D of +6 V on 99- hp 近

TRUE/FALSE QUIZ Answers can be found at www.pearsonhighered.com/floyd. 1. An ideal op-amp has an infinite input impedance. 2. An ideal op-amp has a very high output impedance. 3. The op-amp can operate in both the differential mode or the common mode. 4. Common-mode rejection means that a signal appearing on both inputs is effectively cancelled. 5. CMRR stands for common-mode rejection reference. 6. Slew rate determines how fast the output can change in response to a step input. 7. Negative feedback reduces the gain of an op-amp from its open-loop value. 8. Negative feedback reduces the bandwidth of an op-amp from its open-loop value. 9. A noninverting amplifier uses negative feedback. 10. The gain of a voltage-follower is very high. 11. Negative feedback affects the input and output impedances of an op-amp. 12. A compensated op-amp has a gain roll-off of -20 dB/decade above the critical frequency. 13. The gain-bandwidth product equals the unity-gain frequency. 14. If the feedback…
7 7 76% Q4. Figure 4 shows a circult diagram of the Wien-bridge oscillator. ASsume that the amplifier employed is an ideal op-amp. a) State the Barkhausen criterion for sustained oscillation. b) Explain briefly how the phase shift requirement for sustained oscillation is met in this circuit. c) The feedback ratio of the circuit shown in Figure 4 is given by, %3D 3R +j(2afCR-C) 27/ Derive the expression for the oscillation frequency, f. R. Figure 4 Colpitts oscillator - 7x-
An op-amp comparator in a firing circuit can produce waveforms at the output of up to 20 V peak-to-peak without any distortion. An inverse cosine-based firing circuit with a voltage range from +10 to -10 (reference voltage) is used to produce a gating signal for the SCR at the desired delay angle. if the reference voltage is 5.92 volts, the delay angle (in degrees) would be: O A. None of the other choices are correct O B. 41 O C. 139 O D. 131 O E. 49
One advantage of having feedback in op amp circuit is A.Can control gain B.less complicated C.less input signal D.low gain E.high output voltage F.low bandwidth
4. What is the function of the lead-lag network in the Wein Bridge oscillator? 5. Which type of feedback is used in the Wein Bridge oscillator 6. What is the gain of the Wein Bridge oscillator? 7. What are the applications of the Wein Bridge oscillator? 8. What is the condition for generating oscillations? 9. What is the difference between damped oscillations undamped oscillations? 10. Wein Bridge oscillator is either LC or RC oscillator. 11. What are the drawbacks in using Wein Bridge Oscillators?
Make a circuit using a 741 op-amp chip. The required specs of the circuit are: input impedance 500 Ohm, amplitude gain 20
Q. One advantage of having feedback in op amp circuit is A. low gain B. low bandwidth C. can control gain D. high output voltage E. less input signal F. less complicated
Show the connection of three combination op-amp stages using an LM348 IC to provide outputs that are 110, 1681, and 420 times larger than the input. Use a feedback resistor of Rf = 400 k? in all stages, while can use only (R= 40 k? for first stage), (R= 10 k? for second stage), and (R= 20 k? fot third stage)