The motor shown in the photo is used to turn a wheel and attached blower contained within the housing. The details of the design are shown. If the pulley A connected to the motor begins to rotate from rest with a constant angular acceleration of ag = 2 rad/s?, determine the magnitudes of the acceleration of point P on the wheel, after the pulley has turned 3.06 revolutions. Assume the transmission belt does not slip on the pulley and wheel. 0.15 m. AO aa = 2 rad/s² 0.4 m B (a)

The motor shown in the photo is used to turn a wheel and attached blower contained within the housing. The details of the design are shown. If the pulley A connected to the motor begins to rotate from rest with a constant angular acceleration of ag = 2 rad/s?, determine the magnitudes of the acceleration of point P on the wheel, after the pulley has turned 3.06 revolutions. Assume the transmission belt does not slip on the pulley and wheel. 0.15 m. AO aa = 2 rad/s² 0.4 m B (a)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Example 700 mm An experimental device imparts a force of magni- tude F = 225 N to the front edge of the rim at A w 900 mm simulate the effect of a slam dunk. Determine the moments of the force F about point O and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment. B 300 mm A 3050 mm
Draw the simplified idealization of a damped SDOF system under free vibration with the following properties and initial conditions: M = 2000 kg k = 23,000 N/m C = 500 N-s/m u(0) = 15 mm u'(0) = 17 mm/s Choose only one type of idealization (from the picture below) and be sure to draw both equilibrium position and the initial condition (displaced position). Include all values in the diagram. TTTTITT
An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The minimum force P required to prevent rotation of the flywheel is applied. a.) Which Tension is larger, TA or Ta? Explain b.) What is the angle of contact in radians? c.) What is the value of the ratio T/T3? 800 N.m 60 60 77 A B
A rod 3.5 feet long rotates in a horizontal plane about a vertical axis through its center. At each end of the rod is fastened a cord 6 ft. long. Each cord is inclined at Ø = 450 with the vertical and supports a weight of 45 lbsA. Which of the following gives the speed of rotation “n” in rpm?a) n = 25.12 rpm b) n = 25.12 rpm c) n = 30.20 rpmd) n = 22.13 rpm B. What is the tension in the 5 feet long cord? a) T = 58.47 lbb) T = 63.63 lbc) T = 51.78 lb d) T = 48.25 lb
7) The hemispherical dome in the figure weighs 30 kN and is filled with water and attached to the floor by six equally spaced bolts. What is the force in each atmosphere 3 сm 4 m bolt required to hold the dome down? cylindrical pipe -hemi-spherical dome water 6 bolts
The bucket of the front-end loader shown carries a 3200 lb load. The motion of the bucket is controlled by two identical mechanisms, only one of which is shown. Knowing that the mechanism shown supports one-half of the 3200 lb load. Determine the force exerted by cylinder CD and the force exerted by cylinder FH.
180 mm O 15.18 A series of small machine components being moved by a con- veyor belt pass over a 180-mm-radius idler pulley. At the instant shown, the velocity of point A is 280 mm/s to the left and its accel- eration is 80 mm/s to the right. Determine (a) the angular velocity and angular acceleration of the idler pulley, (b) the total acceleration of the machine component at B.
An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The minimum force P required to prevent rotation of the flywheel is applied. a.) Which Tension is larger, TA or Te? Explain b.) What is the angle of contact in radians? c.) What is the value of the ratio TA/Tg? 800 N.m 60 60° A B
50 rpm 1000 mm 300 mm 3. Determine the centroidal moment of inertia about the X axis.
The portion AOB of a mechanism consists of a 400-mm steel rod OB welded to a gear E of radius 120 mm which may rotate about a horizontal shaft O. It is actuated by a gear D and, at the instant shown, has a clockwise angular velocity of 8 rad/s and a counterclockwise angular acceleration of 40 rad/s². Knowing that rod OB has a mass of 3 kg and gear E a mass of 4 kg and a radius of gyration of 85 mm, determine (a) the tangential force exerted by gear D on gear E, and (b) the components of the reaction at shaft O. 120 mm 00. On If 400 mm
The belt-driven pulley and attached disk are rotating with increasing angular velocity. At a certain 2instant the speed v of the belt is 1.5 m/s, and the total acceleration of point A is 75 m/s . For this instant determine (a) the angular acceleration of the pulley and disk, (b) the total acceleration of point B, and (c) the acceleration of point C on the belt.
Please, reaply as soon as posible. I have little time! Static Problem The band brake shown controls the rotation of the drum. The coefficient of friction between the belt and the drum is 0.25. The weight of the lever is negligible.Determine the force P that must be applied at the end of the braking lever to resist a torque T = 200 lb in, if the torque is applied in the: a) Clockwise b) Counterclockwise direction.