The mechanism shown is used to lower handicapped persons into a whirlpool tub for therapeutic treatment. In the unloaded configuration, the weight of the boom and hanging chair induces a compressive force of 430 N in hydraulic cylinder AB. (Compressive means that the force which cylinder AB exerts on point B is directed from A towards B.) If 0 = 22°, determine the moment made by this cylinder force which acts on point B about (a) point O and (b) point C. The moments are positive if counterclockwise, negative if clockwise. 115 200 Mo= 625 Answers: Mc= 190 i i 365 160 190 925 B 165 Dimensions in millimeters N-m N•m

The mechanism shown is used to lower handicapped persons into a whirlpool tub for therapeutic treatment. In the unloaded configuration, the weight of the boom and hanging chair induces a compressive force of 430 N in hydraulic cylinder AB. (Compressive means that the force which cylinder AB exerts on point B is directed from A towards B.) If 0 = 22°, determine the moment made by this cylinder force which acts on point B about (a) point O and (b) point C. The moments are positive if counterclockwise, negative if clockwise. 115 200 Mo= 625 Answers: Mc= 190 i i 365 160 190 925 B 165 Dimensions in millimeters N-m N•m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

8 kN 2 m -2 m 2 m 14 kN 6 kN DI RDH = A B C 28 kN-m 12 kN-m RA = Rov =' Solve for the following: a. What is the shear at C? b. What is the shear at D? c. What is the moment at B? d. What is the horizontal reaction at D? e. What is the horizontal reaction at A? f. Shear and Moment Diagram
p=57 Calculate the greatest positive torque at point (C) on the bridge shown below that results from the three moving loads. 1.5P+0.5 2P+0.5 P+0.5 2.5 m 1.5 ml B 6 m 6 m
A bent pipe is attached to a wall with brackets as shown. A force of F = 210 lb is applied to the end of the tube with direction indicated by the dimensions in the figure. Determine the support reactions at the brackets B, C, and D. Model these brackets as journal bearings (only force reactions perpendicular to the axis of the tube) and neglect couple moment reactions. Assume the distance between the supports at B and C and the tube bends nearby are negligible such that the support at C is directly above the support at D and the dimension g gives the distance between supports B and C. Enter your answers in Cartesian components. 2013 Michael Swanbom cc i❀O BY NC SA x Z B y g d FL $ h A каж Values for dimensions on the figure are given in the table below. Note the figure may not be to state.
Problem 2: The hydraulic cylinder CF, which partially controls the position of rod DE, is locked in the position shown. Knowing that P = 2 kN and 0 = 75°, determine the forces in pins A, B. C and D. 100 mm 175 mm D B C 20° 200 mm A F 45 mm
3. A bar AB is supported by fixed supports at its ends as shown in the figure. An axial load of 12 KN is applied at point C. Determine the reactions at the fixed supports A and B. 500 mm 400 mm A 12 kN-
Calculate the reactions on the beam bearings in the case of loading in the figure? Solve correctly please.
A fixed crane with a mass of 2000 kg uses a stainless steel cable (Yield Strength =210 MPa) to lift a 2400 kg mass. The center of the gravity of the crane is located at G and ean be used to model the weight of the crane at a single point. • Determine the reactions at A and B • Determine the minimum diameter that the cable should be to lift a 2400 kg object for the given erane using a factor of safety equal to 2.5. 2400 kg 1.5 m B +2 m- 4 m-
4. A planar truss that is supported by a rolling pin support at point I and a fixed pin support at point A is shown in the accompanying figure. Two point loads are applied on the truss at points D and F, as indicated in the figure. Assume that all members of the truss are massless. n₂ 400m 40 FARN an AKN m 300 300 (a) Draw a free body diagram of the entire truss. (b) Using equilibrium conditions, calculate the reaction forces at points A and I. (c) Draw a free body diagram of point H; calculate the axial forces acting on member HH. (d) Determine the axial forces in members DF, DG, and EG.
A 10 m long beam has 2 supports at point A and B. The beam is pinned at Support A and supported by a roller at Support B. It is carrying a car (mass of car= 1660kg) at middle of the beam. Draw the free-body diagram (FBD); construct the shear and bending moment diagram for this system. Discuss the results and explain the stress of this beam. Provide your opinion on the effect of the beam when the centroid of the vehicle is shifted to 3m away from Support B. Using equilibrium i.e. force and moment equilibrium must be satisfied for each component, determine the forces or/and moments. List all assumptions that are
Example The beam ABC is loaded via a 500 N.m couple and a 600 N force as shown. ... The beam is connected to the rest of the system by a pin joint at B and a roller support at ... Determine the magnitude of the reaction forces on the beam at the supports.
The ramp is used as passengers board a small commuter airplane. The total mass of the ramp and six passengers is 730 kg with a ma mass center at G. Determine the force in the hydraulic cylinder AB (positive if in tension, negative if in compression) and the magnitude of the pin reaction at C. 720 mm Answers: 8 AB= i 620 mm- C= i 'В G 1410 mm 2880 mm N N
The beam supports a uniform load of 3.0 k/ft and a concentrated load of 12 k as shown in the figure below. Assume D is a pin support and B is a roller. Determine the reactions at B and D. Write the equation for the bending moment in beam segment BC. Assume "x" is measured from point B. • Write the equation for the shear in beam segment CD. Assume “x;" is measured from point D. 112 k 3.0 k/ft A C 12 ft 12 ft