The mass of the A gear is 10 kg and the turning radius is 200 mm. Of gear B its mass is 3kg and the turning radius is 80 mm. When the system is stationary to gear B. Moment of 6 N.m is applied. By neglecting friction; a) The time elapsed until the angular velocity of gear B reaches 600 rpm. b) Find the tangential force from gear B to gear A.

Q: In the image, blocks A and B have 50 and 10 kg in order of . It is given that the coefficients of…

A: Given: Mass of block A is mA=50 kg and that of block B is mB=10 kg, μk=0.3 and μs=0.4 and P=100N…

Q: An object, m1 with a mass of 10.0 kg placed on a frictionless, horizontal table. It is connected to…

A: The free-body diagram of the above system is drawn below. Here, N, a, and T represent the normal…

Q: The mass of flywheel of an engine is getres. It is found from the turning moment diagre . If the…

A:

Q: When the angle θ = 90 °, the cylinder BE starts with a vertical force (F = 3210 N) Newtons on the…

A: From the given data,

Q: The mass of the A gear is 10 kg and the turning radius is 200 mm. Of gear B its mass is 3kg and the…

A: Tangential force from gear B to A is TA=IAαA=mArA22×arA=mArA2×a⋯⋯⋯(1) Torque applied is…

Q: A wheel with rotational inertia 45 kg.m2 is mounted on a fixed, frictionless axle. The angular speed…

A:

Q: he blades of a rotary lawnmower are 30cm long and rotate at 315rad/s. Find the linear speed of the…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 4. An aeroplane with a two wheel nose gear and four main wheels rests on the ground with a single…

A: The nose wheels are 10 m in front of the main wheels so if the main wheels are taken as a datumso if…

Q: A conical pendulum having a 2 kg mass attached at the end of the string is rotating at a constant…

A: m=Mass of conical pendulum=2 kgV=constant speed=4 m/sR=Horizontal Circle Radius=1 m

Q: Q: A four masses A, B, C and D have attached to rotating shaft. The weigh of each mass is 160, 260,…

A:

Q: A motor is attached to a pulley of radius 10 cm and mass 1 kg. A belt passes through the pulley that…

A: It is asked to find the energy consumption of motor and motor torque

Q: A car weighing 500 kg moving with a speed of 10 m/s takes a turn around a circle with a radius of 25…

A:

Q: Figure 1 shows a simple system to lift a heavy load. The dimensions a = 3.6 m and b = 1.2 m. The…

A: given : W = 20000 g = 20kg CW = 45000 g = 45 kg

Q: In the picture, a weight pulls on a pulley (solid disk) of mass 0.5kg and a radius of 0.25m. The…

A:

Q: Q3: A sircular solid disc of uniform thickness 20 mm, radiues 200 mm and mass 20 kg. is used as a…

A: We have to find kinetic energy of flywheel

Q: 2) Three cylinder A:B:C has a speed ratio of 3:2:4 are externally in contact to each other. If…

A: Given in question 2:Speed ratio of A,B,C=3:2:4Centre distance between A and C=30 in

Q: A flywheel  is fitted to a multi cylinder engine, which runs at a mean speed of 360 r.p.m. If the…

A:

Q: A uniform block of mass m and dimensions a by 2a by 3a spins about a long diagonal with angular…

A:

Q: Four masses A, B, C and D revolves at equal radii and equally spaced along a shaft. The mass B is…

A: Let mass of A,C,D be mA,mC,mD and all the masses are revolving at same radius r and separated by…

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: Q10/ Four masses A, B, C and D as shown below are to be completely balanced. A B C D 30 50 40 Mass…

A:

Q: 1. Derive the equation to find the balancing mass and its angular position in case of static…

A: Given Balanced mass Transference of force Reciprocating balanced To find Equation for balanced mass…

Q: 3) A cam-follower mechanism is used to convert the rotary motion of a shaft into the oscillating or…

A:

Q: Turning moment 1mm = 60Nm: crank angle, 1 mm = 1°. The turning moment shows the maximum energy that…

A: Given: The turning moment, 1 mm = 60 N.m The angle, 1 mm = 1° The unit area, A = 2850 m^2 The mean…

Q: A train engine of mass 10,000kg is linked to a carriage of mass 6,000kg. The engine force acting on…

A: Given: The mass of train engine is M=10,000 kg. The mass of carriage is m=6,000 kg. The engine…

Q: A rotating shaft has four masses m,m2,m3 and ma are 160 kg, 305 kg, 280 kg and 255 kg respectively.…

A: Given: Masses,m1=160kgm2=305kgm3=280kgm4=255kgAngular position of the…

Q: A helical spring has a stiffness of of 25 kN/m. If a mass of 100 kg is attached to its free end,…

A: Given data: Stiffness of spring = 25000 N/mmass = 100 kg

Q: A torque of 1.45 N-m is applied to a thin rod, fixed to rotate about a point through its center. If…

A:

Q: 3kg ball connected to horizontal  AB with cable. AB rotates with constant angular velocity w about…

A:

Q: A space station shaped like a giant wheel has a radius 98 m and a moment of inertia of 5.01 x 108…

A:

Q: A circular disc of uniform thickness of 20 mm, radius of 200 mm and mass of 20 kg, is used as a…

A: Given data Mass =20 kg Radius =200 mm N=600 rpm We have to determine kinetic energy of the flywheel

Q: In the mechanism shown, find the force P and all reaction forces. Ignore weight forces and friction

A: Considering that the mechanism is in equilibrium with the action of the applied torque and external…

Q: A wheel with rotational inertia 48 kg.m2 is mounted on a fixed, frictionless axle. The angular speed…

A: A flywheel is a mechanical device that is used in heavy machines to control the fluctuation of…

Q: A cart (20 kg) is supported by 2 wheels (15 kg each) on a 30 degree incline. The wheels have a…

A:

Q: Now consider two very similar semi trucks. One travels at 40 km/hr and another travels at 75 km/hr.…

A: -considering equal masses ( similar trucks)

Q: Q4. The turning moment diagram for the engine is depicted in below, calculate maximum fluctuation of…

A: Write the data with suitable variables. U1=50 N.mU2=60 N.mU3=50 N.m Here, U1 indicates the energy…

Q: An engine flywheel and a clutch plate are both connected to a transmission shaft. Let the moment of…

A:

Q: A sphere of mass M and radius R is not necessarily solid or hollow. It has moment of inertia I=…

A: Consider a sphere of mass M and radius R is not necessarily solid or hollow. It has moment of…

Q: 50 N 30° Work and Energy: A wheel has a radius of 0.4 m, weighs 50 kg and has a radius of gyration…

A:

Q: A hollow cone (M, R) of semi-angle 30° is rolling without slipping on a fixed cone (same radius and…

A: Data given -  Theta = 30°  M = 2kg  R= 1 m  w = 2 rad/s

Q: 2. (20%) In the rotary system as below, where tire mass m, =12 kg, axle mass m, = 3 kg, and radius…

A:

Q: 3) A cam-follower mechanism is used to convert the rotary motion of a shaft into the oscillating or…

A: Concept           Inorder to find the equivalent mass of system            Sum of all Kinetic…

Q: 4. A 76.0- kg boulder is rolling horizontally at the top of a vertical cliff that is 20 m above the…

A:

Q: Find the force constant of the spring. Assume that the angle that the ramp makes with the horizontal…

A: Given,       mass of the puck  m=0.18 Kg                           angle θ=22°…

Q: A flywheel weighs 325 kg with a diameter of 1.6 m. The flywheel rotates at 600 revolutions per…

A: Given data Mass of flywheel = M = 325 kgDiameter of flywheel = d= 1.6 mInitial speed of rotation =…

Q: A riveting machine is driven by a 3.5 kW motor. The moment of inertia of the rotating parts of the…

A: P=3.5 kW I=67.5 Kg-m2N1=240 rpm∆E=9kN-m…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.