The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.9 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 2.4 m? (b) What is the value of R when x = 4.5 m? (c) Determine the minimum value of R and the corresponding value of x.

The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.9 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 2.4 m? (b) What is the value of R when x = 4.5 m? (c) Determine the minimum value of R and the corresponding value of x.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.125P: The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A...

See similar textbooks

Similar questions

Find the internal force system acting on section 3 for the pin-connected frame.
The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
The jib crane is designed for a maximum capacity of 5 kN, and its uniform I-beam has a mass of 200 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.9 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 0.8 m? (b) What is the value of R when x = 3.2 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 40° m 5 KN -2.9 m 1.2 m Questions: (a) If x = 0.8 m, R= (b) If x= 3.2 m, R= i (c) The minimum value for R = i (d) The pin should be designed to hold i kN kN kN at x = kN.
The jib crane is designed for a maximum capacity of 7 kN, and its uniform I-beam has a mass of 240 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.7 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work.(a) What is the value of R when x = 1.9 m?(b) What is the value of R when x = 3.2 m?(c) Determine the minimum value of R and the corresponding value of x.(d) For what value of R should the pin at A be designed?
The jib crane is designed for a maximum capacity of 9 kN, and its uniform I-beam has a mass of 260 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.4 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 1.6 m? (b) What is the value of R when x = 3.2 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 32° x m 9 KN 1.0 m 2.6 m Questions: (a) If x= 1.6 m, R= i (b) If x= 3.2 m, R = i (c) The minimum value for R = i (d) The pin should be designed to hold i KN KN kN at x = i kN.
The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 190 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.8 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 1.6 m? (b) What is the value of R when x = 3.3 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 37° 6 KN 1.2 m 2.8 m Questions: (a) If x= 1.6 m, R= i (b) If x= 3.3 m, R= i (c) The minimum value for R = i (d) The pin should be designed to hold i kN kN kN at x = kN. i E
The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (You can disregard the plot, I only need a, b, c, and d)
The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 230 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 2.0 m? (b) What is the value of R when x = 3.3 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 34° x 1.3 m 6 kN -2.9 m
The system below is composed of a uniform, slender rod. The mass of each section can be described using its density, p =2.2 kg/m. The distances on the diagram below are: a = 190 mm, b= 310 mm, and c= 430 mm. Determine the magnitudes of the force and moment reactions at the built-in support O. (Hint: Recall the support reactions required for a built-in support. The mass of each section varies according to its length.) b 3 26 3 3a
The machine shown is used to help load luggage into airliners. The combined mass of the conveyor and luggage is 110 kg with mass center at G. Determine and plot the force in the hydruaulic cylinder BC (report your answer as a positive value) as a function of over the range 5° 0 ≤ 36°, then answer the questions. Assume DE = 2070 mm, CD = 1280 mm, c = 1680 mm, d = 1130 mm, e = 570 mm, f = 2380 mm. t Questions: E B i D If 0 = 11°, BC = If 0 = 21°, BC = i Over this range, the maximum value for BC = i N N N and occurs when 8 =
The 4.8 m I-beam has a mass of 900 kg and is held in the horizontal position by the pin at O and by the vertical cable which passes around the pulley at A and around the drum of the 200 kg motorized winch at B, as shown in Figure 8. If the winch motor has an output starting torque of 800 N.m, calculate the reaction forces at the pin O given the moment of inertia of the whole system including the winch, lo 7272 kg.m?. Treat the beam as a slender bar and the winch unit as a mass concentrated at the centre of the pulley.
The weight of the limb is W=15 lbs.The contact of foot with the ground can be modeled as a pin/hinge here. Determine the reaction force of the ground and the reaction at the knee joint and its direction/angle θ. Note: use the thee force member condition to find the angle of FK.