The insulated compressor of a large gas turbine received air from the surroundings at 1 bar and 20°C At the compressor discharge, the pressure is 4 bar, the temperature is 130°C, and the velocity is 12 m/sec. The power input to the compressor is 4,000 hp. Determine the mass flow rate of the air i kg/sec.

The insulated compressor of a large gas turbine received air from the surroundings at 1 bar and 20°C At the compressor discharge, the pressure is 4 bar, the temperature is 130°C, and the velocity is 12 m/sec. The power input to the compressor is 4,000 hp. Determine the mass flow rate of the air i kg/sec.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam enters the nozzle operating a steady state pressure of 2.5 MPa and a temperature of 300 °C ( H1 = 3008.8 kJ/kg) and leaves at a pressure of 1.7 MPa with a velocity of 470 m/s. The rate of flow of steam through the nozzle is 1360 kg/hr. Neglecting the inlet velocity of the steam and considering the flow in the nozzle is adiabatic, find:a. the exit enthalpy in kJ/kg, ( H2)b. the nozzle exit area ( in cm) if V exit is 0.132 m^3 /kg c. the system
Air is compressed from 14.7 psia, 70 ° F, to 50 psia, 250 ° F by a centrifugal compressor at a rate of 50 lbm / min. The temperature rise of the cooling water flowing through the jacket is 7 ° F for a flow rate of 50 lbm / min. Calculate the power required in hp to operate the compressor, ignore kinetic energy changes.
1. A horizontal "hot air blower" consists of a fan, an electrical heating element and a nozzleThe power input to the fan is 50 J/s and the power input to the heating element is 1.44 kJ/s. The air enters the fan with negligible velocity at a pressure of 1 bar and a temperature of 20 C, the volumetric flow rate being 0.5 m3/min. After passing over the heating element, the air leaves the nozzle with a velocity of 25 m/s and a pressure of 1.1 bar. Treating the complete arrangement as a steady flow system and ignoring any heat loss from the system, determine: (a) The mass flow rate of air entering the fan in kg per second(b) The kinetic energy of the air leaving the nozzle per second(c) The change in enthalpy of the air occurring per second between entering the fan and leaving the nozzle(d) The temperature of the air as it leaves the nozzle.(e) The density of the air as it leaves the nozzle(f) The flow area at the nozzle exit.Take R = 0.287 kJ/kgK and cp = 1.005 kJ/kgK
A 12" x 14" horizontal single-acting reciprocating air compressor is driven by a 50 kW motor that operates at 520 rpm, drawing in air at 14 psia and 88 F, and discharging it at 57.6 psia. The compression and re-expansion process are polytropic with n = 1.33. Mechanical efficiency = 85 %, compression efficiency = 75% Calculate: a). the mass of air (lb/min) discharged b). volumetric efficiency (%) c). the percent clearance (%)
In turbochargers a turbine is directly connected to a compressor. The power harvested by the turbine is used to power the compressor. In the figure below a turbine runs on steam and powers a compressor on air. Air can be considered a perfect gas with k = 1.34, R = 0.28 kJ/kgk and cp = 1.02 kJ/kgK. The air enters the compressor at p₁ = 1bar, T₁ 300K and a mass flow rate of mdot = 5.9 kg/s and exits at p2 = 5.2 bars. The steam enters the isentropic turbine at P3 = 2 MPa, T3 = 320°C and exits at p4 = 100 kPa. 9 State 2 Isentropic Compressor State 1 Air - perfect gas T₁=300K P₁ = 1 bar W Answer: tubine =? State 4 Isentropic Turbine State 3 Steam T3=320°C P3= 2MPa What is the quality of steam leaving the turbine?
Steam enters a nozzle at a pressure of 7 bar and 200°C (i.e. initial enthalpy 2850 kJ/kg) and a pressure of 1.5 bar. The initial of steam at the leaves at entrances is 40 m/sec and exist velocity from the nozzle is 700 m/sec. The mass flow rate through the nozzle is 1400 kg/hr. The heat loss from the nozzle is 1105 kJ/hr. Determine the final enthalpy of steam and the nozzle area if the 3 specific volume is 1.24 m / kg.
4. In a natural gas pipe line compressor, 110 m³/min of propane is compressed polytropically. The inlet pressure is 101 kPaa and the temperature is 38°C. The process follows pV1.08 = C. The exit pressure is 510 kPaa. Determine (a) the exit temperature in kelvins, (b) the mass flow rate in kg/s, and (c) the heat loss in kW. Draw the P-V and T-S diagrams
In turbochargers a turbine is directly connected to a compressor. The power harvested by the turbine is used to power the compressor. In the figure below a turbine runs on steam and powers a compressor on air. Air can be considered a perfect gas with k = 1.34, R = 0.28 kJ/kgk and cp = 1.02 kJ/kgK. The air enters the compressor at p₁ 1bar, T₁ = 300K and a mass flow = rate of mdot = P3 = 2 MPa, T3 = 320°C and exits at p4 5.9 kg/s and exits at p2 = 5.2 bars. The steam enters the isentropic turbine at = 100 kPa. 9 State 2 Isentropic Compressor State 1 Air - perfect gas T₁ = 300K P₁= 1 bar W = ? tubine Answer: State 4 Isentropic Turbine State 3 Steam T3=320°C P3= 2MPa How much power is required to run the compressor? Please enter your answer in kW.
In turbochargers a turbine is directly connected to a compressor. The power harvested by the turbine is used to power the compressor. In the figure below a turbine runs on steam and powers a compressor on air. Air can be considered a perfect gas with k = 1.34, R = 0.28 kJ/kgk and cp = 1.02 kJ/kgK. The air enters the compressor at p₁ 1bar, T₁ = 300K and a mass flow rate of mdot = 5.9 kg/s and exits at p2 5.2 bars. The steam enters the isentropic turbine at P3 = 2 MPa, T3 = 320°C and exits at p4 = 100 kPa. = = State 2 Isentropic Compressor State 1 Air-perfect gas T₁ = 300K P₁= 1 bar Answer: W tubine = ? State 4 Isentropic Turbine State 3 Steam T3=320°C P3= 2MPa What is the mass flow rate of steam through the turbine? Please enter your answer in kg/s
In turbochargers a turbine is directly connected to a compressor. The power harvested by the turbine is used to power the compressor. In the figure below a turbine runs on steam and powers a compressor on air. Air can be considered a perfect gas with k = 1.34, R = 0.28 kJ/kgK and Cp 1.02 kJ/kgK. The air enters the compressor at p₁ 1bar, T₁ = 300K and a mass flow rate of mdot = 5.9 kg/s and exits at p2 = 5.2 bars. The steam enters the isentropic turbine at P3 = 2 MPa, T3 = 320°C and exits at p4 = 100 kPa. = = State 2 Isentropic Compressor State 1 Air - perfect gas T₁ = 300K P₁ = 1 bar Answer: W tubine = ? State 4 Isentropic Turbine State 3 Steam T,= 320°C P3= 2MPa What is the enthalpy at state 4? Please enter your answer in kJ/kg
Moodle in the Cloud 0% In turbochargers a turbine is directly connected to a compressor. The power harvested by the turbine is used to power the compressor. In the figure below a turbine runs on steam and powers a compressor on air. Air can be considered a perfect gas with k = 1.34, R = 0.28 kJ/kgk and cp = 1.02 kJ/kgK. The air enters the compressor at p₁ 1bar, T₁ = 300K and a mass flow rate of mdot = 5.9 kg/s and exits at p2 = 5.2 bars. The steam enters the isentropic turbine at P3 = 2 MPa, T3 = 320°C and exits at p4 = 100 kPa. = State 2 Isentropic Compressor State 1 Air - perfect gas T₁ = 300K P₁= 1 bar Get Help Answer: W = ? tubine State 4 Isentropic Turbine State 3 Steam T,=320°C P3= 2MPa What is the power produced by the turbine? Please enter your answers in kW.
In turbochargers a turbine is directly connected to a compressor. The power harvested by the turbine is used to power the compressor. In the figure below a turbine runs on steam and powers a compressor on air. Air can be considered a perfect gas with k = 1.34, R = 0.28 kJ/kgk and Cp 1.02 kJ/kgK. The air enters the compressor at p₁ 1bar, T₁ 300K and a mass flow rate of mdot = 5.9 kg/s and exits at p2 = 5.2 bars. The steam enters the isentropic turbine at P3 = 2 MPa, T3 = 320°C and exits at p4 = 100 kPa. = State 2 Isentropic Compressor State 1 Air-perfect gas T₁ = 300K P₁ = 1 bar W = ? tubine Answer: State 4 Isentropic Turbine State 3 Steam T, 320°C P3= 2MPa What is the enthalpy at state 3? Please enter your answer in kJ/kg =