The inner diameter of this shaft is 80 mm and the outer diameter is 100 mm. The applied loads are shown in the figure below. The allowable normal stress on plane a -a is 80 Mpa and the allowable shear stress on the same plane is 45 Mpa. Determine the maximum allowable load P that can be applied on the member. Note that point A is on the surface of the shaft.

The inner diameter of this shaft is 80 mm and the outer diameter is 100 mm. The applied loads are shown in the figure below. The allowable normal stress on plane a -a is 80 Mpa and the allowable shear stress on the same plane is 45 Mpa. Determine the maximum allowable load P that can be applied on the member. Note that point A is on the surface of the shaft.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.4P: .4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the...

See similar textbooks

Similar questions

2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the allowable normal stress for bar CB is Operm 10 ksi, determine the diameter of the pins at A and B and that of the square bar CB. Pin A is in double shear while Pin B is in single shear. Ignore points D and E. (^ } 2.5 ft -3 ft -5 ft 150 lb/ft Fx =
3. The composite bar consists of a 20-mm diameter steel segment AB and 50-mm diameter brass end segments DA and CB. Find the stress on each segment due to the applied loads. E of steel is 200 GPa and E of brass is 101 GPa. 250mm 250mm 250mm 50mm 20mm 50mm 75KN 100KN brass steel brass D B C 75KN 100KN
The state of plane stress at a point is shown on the element in Figure below. Represent this state of stress on an element oriented 45° counterclockwise from the position shown. 16 ksi 10 ksi 8 ksi
1. A 60-mm diameter steel tube with a wall thickness of 3 mm just fits in a rigid hole. Determine the tangential stress developed if an axial compressive load of 12 kN is applied. Use v = 0.30 and E = 200 GPa. Answer: 0 = 6.37 MPa 2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid block. It has a diameter of 70 mm and a wall thickness of 5 mm. The tube then sustained an internal pressure of 4.5 MPa. Use v = 0.33 and E= 83 GPa. Compute the tangential stress in the tube. Answer: Ot = 5.20 MPa
The rigid bar ABC supports a load of 21.1 kN at point C. A circular rod (diameter 25 mm) supports the bar at B. The length of AB is 3.5 m and the length of BC is 1.1 m. Calculate the normal stress in the rod. Provide your answer to 2 decimal places in MPа. Rod diameter = 25mm В y F kN
A flanged bolt coupling connects shafts on each side. It consists of 8- 19 mm diameter bolts on a bolt circle of 300 mm and 6 – 12 mm diameter bolt on a bolt circle of 230 mm. Determine the stress on BOLT CIRCLE land the stress on BOLT CIRCLE 2 (in MPa) due to a torque of 20 KN-m. (in MPa)
The drill shown is jammed in the wall and is subjected to the torque and force shown in the diagram. Determine the normal stress (in MPa) at point A on the cross section of the drill bit at section a−a. What is the transverse shear stress (in MPa) at the same point in the drill bit? What is the torsional stress at the same point in the drill bit?
Find the maximum normal stress carried in the part shown. 0-Sin 0.5in 3in S000 1b lin 2in S000 1b 4in 2in
A state of stress at a point A is given by σx = 45 MPa, σy = 9.1 MPa, and τxy = -5.75 MPa. What is the maximum in-plane shear stress for the point A.
Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.
A rod is composed of three segments as shown and carries the axial loads P1=120 kN and P2=50 kN as shown in the figure. Determine the stress in the aluminum segment. Express your final answer in MPa to the nearest whole number. Note: Do not include the unit in your answer. 600 mm- -400 mm- 300 mm A B D Steel Aluminum E = 70 GPa А 3D 1200 тm? А%3D600 mm2 Bronze E = 200 GPa E = 83 GPa А 3D 2400 тm?
Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 2.5 kN. The crankshaft dimensions are b1 = 80 mm, b2 = 135 mm, and b3 = 55 mm. The diameter of the upper shaft is d = 26 mm. Determine the normal stress at point A, which is located on the surface of the upper shaft at the z0 axis. | Yo B b3 Lütfen birini seçin: a. -155.971 MPa b. -200.302 MPa c. None d. -520.946 MPa e. -124.141 MPa