The force system shown consists of the couple C and four forces. The resultant of this system is a 800-lb-in. counterclockwise couple. Determine the magnitude of the couple C (in Ib-in). * Your answer

Q: 1. Assuming F is 90lb, coefficient of static friction: =0.2, and the coefficient of kinetic friction...

A: we have to determine the distance travelled by the box along the plane

Q: The truss is composed of equilateral triangles an supports the load L. Determine the forces in membe...

A:

Q: For the simply supported beam subjected to the loading shown, derive equations for the shear force V...

A:

Q: kw per cylir of the crank and combu

A:

Q: The 3/4" bolts holding the steel plates together below can withstand a maximum shear stress of 36 ks...

A:

Q: 2. Calculate the instantaneous velocity and instantaneous acceleration of a particle traveling along...

A:

Q: Two spherical marbles are released from rest in a viscous fluid. The marbles are made of the same ma...

A: Correct answer: The magnitude of the buoyant force on a marble equals the magnitude of its weight...

Q: 1. Find the centroid of the shaded region. -12 cm- 4 cm 4 cm 3 cm cm '3 cm 2 cm 2 cm

A: Draw the given diagram with segments.

Q: cess. The lengtl en by the expre s the time in minu

A:

Q: 1. A two-storey residential house with special moment-resisting frame (SMRF) has the following infor...

A:

Q: 30 mm 150 mm y 30 mm 150 mm The moment of inertia (in mm) about the axis of symmetry is nearest?

A:

Q: Two kg of water at 105°C and a quality of 50% (i.e. x = 0.5) is first heated until the piston locks ...

A: Given; m = 2kgT1=105°Cx1=0.5T3=90°Cx3=1

Q: What is the center of gravity in this figure?

A: given; center of gravity on given figure?  

Q: Background, theories/concept and objectives of vernier caliper

A: Vernier Caliper  Background/ History :  The first vernier caliper was invented by Pierre Vernier in ...

Q: a surface which has a ref as measured indirectly by

A:

Q: An electronic component with dimension of 5 cm wide, 6 cm high, and 9 cm long is cooled by aluminum ...

A: Fins are used to improve heat transfer from surfaces in a variety of applications. When the availabl...

Q: 4. A submersible pump delivers 350 gpm of water to a height of 5 ft from the ground. The pump was in...

A:

Q: An electronic component with dimension of 5 cm wide, 6 cm high, and 9 cm long is cooled by aluminum ...

A:  

Q: 2.0 lb of water inside a piston-cy inder assembly undergoes the following two processes in series Pr...

A: .

Q: 3. An aluminum sample was tensile tested with a force of 35,500 N. The sample has a rectangular cros...

A:

Q: The flow inside the intake of a scramjet is found to be supersonic with Mach number of 2.5. From the...

A: Given: The Mach number, M1 = 2.5 The static pressure, P1 = 1 atm The static temperature, T1 = 290 K ...

Q: F SIMPLE STRESSES 2. Based on Problem No. 1, determine the shear stress in the grain of the timber c...

A: NOTE:- since, value for F and a is not given i tool as a variable and solve the question. If you hav...

Q: The radiative heat transfer rate per unit area (W/m²) between two plane parallel grey surfaces (emis...

A:

Q: A tank 1.5 m stands on a trolly and is full of water. It has an orifice of diameter 0.1 m at 0.3m fr...

A: Given:h=1.5 md=0.1 mCd=0.6

Q: Block 2 slides outward on link 1 at a uniform velocity of 6 m/s as shown in the figure. Link 1 s rot...

A:

Q: to the ght rigid bar are identical except for ength. Before the load W = 6500 lb. ras attached, the ...

A:

Q: Figure 3 shows cross section of a duct. If each wall is 100 cm, surface C is insulated, and duct is ...

A: Calculating shape factor for surface 1 with itself d= 100 cm= 1m h= 1 sin(60) =0.866 m F1-1 = 1- d/...

Q: l engine is 30%. If air to fact ratio by weight is 20 and calorific value of fuel is 41800 kJ/kg. Fi...

A:

Q: A) 21.5 B) 20 C) 18.9 D) 18.75

A: Geometric Progression or a G.P. is formed by multiplying each number or member of a series by the sa...

Q: 2.0 lb of water inside a piston-cy inder assembly undergoes the following two processes in series Pr...

A: At a particular temperature and pressure, saturated steam is formed when the liquid and gaseous phas...

Q: Radiation. A black body of total area 0.054m² is completely enclosed in a space bounded by 57 mm thi...

A: Given DataA=0.054m2t=57mm=0.057mTi=185°C=458KTo=25°C=298Kσ=5.67×10-8W/m2K4k=1.05W/mK  

Q: During test on a sample of steel bar 25 mm in diameter, it is found that the pull of 50 kN produces ...

A: Given data as per question Diameter=25 mmArea of bar=π4×252=490.87 mm2Force=50 kNdeformation in leng...

Q: Q17. A ball is being pushed by a rod in the vertical plane along a curved path with (C · 0) m, where...

A: Solution: Given Data: r=CθC=0.4θ=1.4 radθ.=1.3 rad/sθ..=2.8 rad/s2

Q: An air-standard Otto Cycle with a compression ratio of 9.0 has air entering at 101 kPa and 27 deg C....

A:

Q: Water contained in a closed tank, initially saturated vapor at 200oC, undergoes an isothermal coolin...

A:

Q: For a specific volume of 0.5 m3/kg, find the quality of steam if the absolute pressure is (a) 40 kPa...

A: Find quality and temperature at given pressure. Given data:- Specific volume = 0.5 m^3/kg P1=40kpa P...

Q: 5.19 : The temperature in a surface condenser is 37.651°C and a vacuum is 700 mm of Hg. Barometer re...

A: The partial pressure is the pressure exerted by each component if it were in the same volume as the ...

Q: 3) An ideal gas consisting of one mole of molecules of type A is in contact with the surroundings at...

A: Change in Gibbs free energy (∆G) is given by, ∆G = (∆H) - T (∆S) (∆H)= change in enthalpy = -xε = -3...

Q: PROBLEM 3 Steel: A = 500 mm ,= 120 MPa 1.8 Find the maximum allowable value of P for the column. The...

A: The normal stress developed inside a member when acted upon by an axial force ca be calculated using...

Q: 4. A motorcyclist travels along a straight road at a speed of 32 m/s. When the brakes are applied, t...

A:

Q: The diagram shows a tank draining into another lower tank through a pipe, both tanks are open. Calcu...

A:

Q: Figure 8-19 is a cross-section of ASTM A36. A total of N bolts are to be used to resist a separating...

A: according t o given question

Q: It is required to cut screw threads of 2 mm pitch on a lathe. The lead screw has a pitch of 6 mm. If...

A: Given data: Pscrew thread=2 mmPlead screw=6 mmNs=60 rpm Need to determine the speed of lead screw.  

Q: At a production machine, parts arrive according to a Poisson process at the rate of 0.35 parts per m...

A: Given:arrival rate, λ=0.35 parts per minuteservice rate, μ=12=0.5 per minute

Q: A stone is thrown at 16 m/s with an angle of 40° above the horizontal from the roof top of the build...

A:

Q: container is filled with a mixture of 2 fluids having densities of 3 kg/L (fluid A) and 4000 kg/m^3 ...

A: The overall density of the mixture can be calculated using the formula given below as- ρo=mtV where,...

Q: Give the correct answer and clear solutuion of the problem  1. What force F must be applied to the ...

A:

Q: v(-ん) Is us 6s 85 t(s)

A: The total path covered by the body during its motion is defined as the distance, while displacement ...

Q: 320 mm 470 mm 42 mm 54 mm T= 2.2 kN.m Aluminium Steel Figure Q1/ Rajah S1 The solid aluminium cylind...

A:

Q: In the graphic below, Gear A begins at rest and is given an angular acceleration clockWise of a = 3t...

A: Given:α=3trA=6 inrB=2 inrc=4 inrD=1 in

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.