The floor of an apartment building shown is subjected to a uniformly distributed dead load of 1.5 kPa and a uniformly distributed live load of 1.9 kPa over its surface area. Determine the service (ASD) reaction (kN) of girder AF that will be transferred to the column at F. Girder Floor beam Column Į B FH G L H M 4 at 7.5 m = 30 m D N E -Io ,2 at 12 m = 24 m

The floor of an apartment building shown is subjected to a uniformly distributed dead load of 1.5 kPa and a uniformly distributed live load of 1.9 kPa over its surface area. Determine the service (ASD) reaction (kN) of girder AF that will be transferred to the column at F. Girder Floor beam Column Į B FH G L H M 4 at 7.5 m = 30 m D N E -Io ,2 at 12 m = 24 m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

A bridge girder AB on a simple span of length L = 20 m supports a distributed load of maximum intensity q at midspan and minimum intensity g/2 at supports A and B that includes the weight of the girder (see figure). The girder is constructed of three plates welded to form the cross section shown. 500 mm L= 20 m 18 mm 1600 mm 500 mm (a) Determine the maximum permissible load q based upon an allowable bending stress oallow = 130 MPa. Round to the nearest tenth. kN Gmax = (b) Determine the maximum permissible load q based upon an allowable shear stresS Tallow = 55 MPa. Round to the nearest tenth. kN Gmax m
1 - Determine the maximum shearing stress in the beam for the loading shown in the figure. The same beam cross-section was used in HW 5. 2 KN 0.5m- 1KN - 0.5m 107 30 30 T dimensions in mm lok beam cross-section
4. The beam shown supports the load shown, determine max flexural stress developed and 200mm the max beam shear developed in the beam 2000N 1m 1m 600N/m 4m 888 30mm 40mm 150mm OC €
A rigid plate C is used to transfer a 20-kip load P to a steel (E = 30,000 ksi) rod A and to an aluminum alloy (E = 10,000 ksi) pipe B as shown. The supports at the top of the rod and the bottom of the pipe are rigid, and the materials were unstressed before the load was applied. The cross-sectional areas of rods A and pipe B are 0.80 in2 and 3.00 in2 respectively. Determine The normal stress in rod A in ksi, The normal stress in pipe B in ksi and The displacement of plate C in inches. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 5 decimal places.
Figure 6: X 5 m 5 m A 5 m 20 KN A simple truss is subjected to 20 kN force at the point A as shown in Figure 6. The reaction force at point C is (in kN): (a) 20 Compression (b) 20 Tension (c) 30 Compression (d) 30 Tension الاختيارات B A O со
As shown in the figure below, determine the internal loadings at point C. В 0.1 m 0.5 m C -0.75 m - -0.75 m -0.75 m (FN x 100) N EN = 78
A simply supported beam is loaded by the couple M3D2000 N-m as shoWh. The beam has a channel-type cross section as illustrated. 3 cm 30 cm 3 cm T 3 m 10.5 cm BI 12 cm main 3 cm M- Determine the maximum tensile stress in the beam. 1.60 MPa O 3.73 MPa )2.49 MPa O1.07 MPa Determine the maximum compressive stress in the beam. * 3.73 MPa 1.07 MPa O 2.49 MPa O160 MPa Determine the maximum shear stress in the beam. 0.0588 MPa ) 0.0490 MPa 0.0653 MPa () 0.0667 MPa
PE Problem for Modules 3.3 and 3.4: Determine the deflection at the end of the overhang by conjugate beam method or Castigliano's theorem. *
The member shown has a rectangular cross section, determine the state of stress that loading produces at point C. 1.5m 1c T 250mm 2.5m 125mm 1.5m 50mm 4m + 2m 50kN/m
At which point on the design P-M interaction diagram is the design flexural strength largest? O Pure compression Pure tension Balanced failure point (CCL limit) O TCL limit Beam condition (Pn = 0) %3D //img00.zhaopin.cm
A prismatic beam (as shown below) has plastic moment capacity of Mp, then the collapse load Pof the beam is P P/2 L/2 – - L/2 + L/3
Q1 A truss system is shown in Figure Q1. It is loaded at joints D and E as shown. The truss members are to be manufactured from Aluminium Alloy cylindrical bar with a tensile yield stress of 300 MPa, a compressive yield stress of 200 MPa, and Young's Modulus of 70 GPa. 1.5m 1.5m A B 4001 10 KN 3m Fig. Q1 E 水 20 KN 1.5m D ➜ (a) Show that the truss system can be described as statically determinate. (b) Draw a Free Body Diagram of the truss and determine the reactions at the supports. (c) Use the METHOD OF JOINTS to determine the load in each member of the truss, indicating whether they are tensile or compressive.