The error in measuring the radius of a 5cm circular rod was 0.2%. If the cross-sectional area of the rod was calculated using this measurement, then the resulting absolute percentage error in the computed area is (round off to two decimal places) Enter Your Answer... Check

The error in measuring the radius of a 5cm circular rod was 0.2%. If the cross-sectional area of the rod was calculated using this measurement, then the resulting absolute percentage error in the computed area is (round off to two decimal places) Enter Your Answer... Check

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter14: Computational Engineering Tools Electronic Spreadsheets

Section: Chapter Questions

Problem 20P

See similar textbooks

Related questions

Q: A 50 cm square precast pile is driven by 9 m into a sandy soil. The standard penetration test…

A: B = 50 cm or 0.5 m L = 9 m Qa = 1100 kN

Q: The basic data for proportioning trial batches for normal weight concrete with an average with an…

A: w/c ratio = 0.48 Water content = 180kg/m3

Q: The bioreactor volume (V), F/M ratio, and HRT are respectivel O 250 million gallons, 0.28…

A: A continuous stirred tank reactor (CSTR) Activated Sludge Process is used to treat municipal…

Q: Same as Example 2.1, except that only the left loaded area exists and the Poisson ratio is 0.3, as…

A: Stress strain and deflection at 10 in below surface.

Q: Find the deflection of the cantilever supported beam of 7 m span, 100 kN at free end. The beam width…

Q: Q: - Analysis the beam shown below by the method of consistent deformation. El = constant A दे * 20…

A: A continuous beam fixed at C and roller supported at A and D. The beam is loaded with 20kN/m UDL…

Q: i). Determine the design spacing for the combined shear & torsion using a 12mm-dia. closed stirrup…

Q: 17) The friction load capacity of the pile using the B-method is most nearly: a. 437 kN b. 927 kN c.…

A: To determine- Friction load capacity

Q: A vertical cylindrical steel storage tank has 30 m diameter and the same is filled up to a depth of…

Q: A cut is to be made in a soil 16.5 kN/ms having = 0= 15°. The side of the cat slope will make an…

A: Properties of soil are: γ=16.5kNm3c'=28.7kNm2φ=15oβ=45oFS=3

Q: ans

A: Determine the reaction at A and B of the beam using Castigliano's theorem.

Q: ▪ Derive the following equation of maximum deflection using double integration method. 15. W W T.…

A: Given continuous beam with concentrated loading

Q: Sketch all the possible yield line pattern for the slabs shown in Figure Q2(a). All supports are…

Q: A canal irrigates a portion of a culturable command area to grow sugarcane and wheat. The average…

A: The average discharge required to grow sugarcane = 0.36 cumecs The average discharge required to…

Q: The culturable command area for a distributary channel is 20,000 hectares. Wheat is grown in the…

A: Command area A=20,000 haIntensity of irrigation I=50%=0.50Kor period t=30 dayskor water depth D=120…

Q: Q- At a horizontal curve portion of a 4 lane undivided carriageway, a transition curve is to be…

A: A 4 lane undivided carriageway, n=4, Design speed V=60 kmph, Radius of curve R=245 m, Wheel base…

Q: 2. ROTARY PUMP Given: Discharge weight = 25.3 kg Current = 0.50 amp Duration = 1 minute Required:…

Q: 40kH & 70KM. E 100KH. I B TITK tam tem M 7m K 50.11m² 50.14 m² 60.18m² $ 0.21 m² H 3m 6m 5m Using…

Q: Water at 15°C is to be discharged from a reservoir at a rate of 18 L/s using two horizontal cast…

A: Discharge rate, Q=18 L/s=0.018 m3/s Length of first pipe, L1=20 m Diameter of first pipe, D1=6…

Q: It is known that q = 2kN/m, 1 = 6m in the shown structure. Determine the force in the tension link…

Q: Figure Part A P= A Value 26₁ +26+21= ft If the beam is made from wood having an allowable shear…

A: We have to find the maximum value of P

Q: A 300 mm x 300 mm concrete column which is pin connected at both ends has an unsupported length of…

A: 300 mm x 300 mm concrete column Lu = Unsupported length = 4.6 meters = 4600 mm Pu = Total factored…

Q: 2) Find the support responses of the plane lattice in the figure and calculate the rod forces 1, 2,…

A: Determine the support reaction and force in member 1,2,3 and 4.

Q: 2 k/ft A 3 k/ft 600 k ft 12 ft 12 ft 2 k/ft B 60°

Q: Gradually Varied Question 3: A rectangular channel 2m wide carries a discharge of 10m³/s at a depth…

A: Width, B = 2 m Depth of water, y = 2 m Discharge, Q = 10 m3/s It is needed to find the specific…

Q: Q11/ A rectangular storage tank with an open top is to have volume (20 m³). The length of the base…

Q: A trapezoidal weir has a side slope of 1 horizontal to 4 vertical. The head over the weir is 2.5 ft…

Q: Q8] The specific energy in a 2.0 m wide rectangular channel is not to exceed 1.2 m. What maximum…

Q: The perception-reaction time for a vehicle travelling at 90 km/h, given the coefficient of…

A: →Stopping Sight Distance (SSD)=170 m→Design speed of vehicle (v)=90 kmhr→acceleration due to gravity…

Q: A superspeedway in New Delhi has among the highest super-elevation rates of any track on the Indians…

A: A superspeedway in New Delhi- Radius R = 335 m and 33° banking. To Find- The coefficient of side…

Q: A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ,…

A: b = 300 mm d = 350 mm f'c = 30 MPa fy = 345 MPa NOTE : As per guidelines, first question is…

Q: If you want to estimate the trip generation in a city you are interested in, what factors you will…

A: There are several factors that can influence trip generation in a city, but two significant factors…

Q: The design speed for a two-lane road is 80 kmph. When a design vehicle with a wheel base of 6.6 m is…

Q: 6. P mix X 12EI 4 for 0<x<- 8 max P1³ 48EI

A: As both question are separate question ,hence solving only first one. Kindly upload question…

Q: Determine the discharge in liters/s of a new 1.0 m diameter cast iron pipe if the friction loss is…

A: Diameter, D = 1m Friction loss = 10 kPa Length, L = 100 m Specific gravity, S = 0.912 kinematic…

Q: Q1] Calculate the critical depth and the corresponding specific energy for a discharge of 5.0 m³/s…

Q: Q7/Three pipes are connected in series 1,2 and 3 are 300 m of 300 mm diameter, 150 m of 200 mm…

Q: Three forces are acting on the five-member frame as shown. The free-body diagram of the member ABC…

A: The magnitude of the vertical force = 300 N The magnitude of the horizontal force = 150 N To…

Q: In this problem, assume a propagation speed of 45 km/hr and that each toll booth takes 6 seconds to…

A: Propagation Speed, V = 45 km/hr Time taken at each toll booth = 6 sec/car Number of cars in a…

Q: If a pumping well extracts water at a rate of 0.1 cumecs from a confined, homogeneous aquifer of…

A: water rate = 0.1 cumecs thickness if aquifer = 33.1 m porosity = 0.04 to find - magnitude of…

Q: A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate m of 34 kg/s. The…

Q: Derive and show the relationship or transformation of Ws = Ys Vs →→ to Ws=ite v Gm your

Q: What will be the load carrying capacity (kN) of a group of 6 piles, if the individual load carrying…

Q: A drinking water treatment plant with conventional treatment uses on disinfection segment consisting…

A: Baffling factor = 0.5 Theoretical detention time (TDT) = 270 min Average free chlorine residual= 1.6…

Q: Consider the strip footing shown in the figure below. The soil consists of sand with f’ =36° and…

A: The angle of friction = 36° The effective cohesion (c') = 0 The saturated unit weight of the clay =…

Q: Subject: Construction Quality Management What are the characteristics of a good quality plan?…

A: Good quality plan - Good quality plan can be defined as well defined set of documents which includes…

Q: Determine the force in members FG, EG, FD and FE of the truss and state if the members are in…

Q: The error in measuring the radius of a 5cm circular rod was 0.2%. If the cross-sectional area of the…

A: given- radius=R=5 cm area=A % error in area needs to be find out.

Q: Determine the force in the member BG in th given truss 4KN FX

A: To Find : Force in member BG ?

Q: 10) A 10.75 cm diameter steel pile is driven 25 m into stiff, insensitive clay. The pile has an…

A: Given; Diameter of pile (d) = 10.75 cm = 0.1075 m Length of the pile (l) = 25 m Friction capacity…

Question

Civil engineering

The error in measuring the radius of a 5cm circular rod was 0.2%. If the cross-sectional area of the rod was
calculated using this measurement, then the resulting absolute percentage error in the computed area is
(round off to two decimal places)
Enter Your Answer...
Check

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: given

VIEW

Step 2: calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The error in measuring the radius of a 5cm circular rod was 0.2%. If the cross-sectional area of the rod was calculated using this measurement, then the resulting absolute percentage error in the computed area is (round off to two decimal places) Enter Your Answer... Check
The error in measuring the radius of a 5 cm circular rod was 0.2%. If the cross- sectional area of the rod was calculated using this measurement, then the resulting absolute percentage error in the computed area is_ .(round off to two decimal places)
Example-2 : For measuring the area of a figure using planimeter, the anchor point was placed outside and the tracing point was moved in clockwise direction. The initial and final readings were observed to be 3.385 and 6.729 respectively. Zero on the disc passed the index mark once in forward direction. If the multiplying factor is 100 cm², find the area of the figure. If the figure is drawn to a scale 1 : 10000, find the area on ground, in km².
Activity 3. Solve the following word problems and present your solution. 1. A surveyor's steel tape measure is calibrated at 65°F. a reading of 200 ft is found when the tape measure is used to determine the width of a building lot when the temperature is 10°F. How great an error does the temperature difference introduce? The coefficient of linear expansion steel is 6.7 x 10-6/°F.
The radius and height of a right cylinder are measured at 2.9m and 1.6m respectively with a maximum error of 2%. Compute the resulting percentage error measured in the volume of the cylinder by the formula V = ar?h. Assume the value of n is %3D exact for calculation.
Answer this problem and use 2 decimal places and box the final answer. Thank you.
An engineering function is given by a = y?e? cos x At x = 1.3,y = 2.1, and z = 4.9, compute the absolute and relative erors if the error in the values of x,y and z are 0.05 (correct to 5 decimal digits)
A bar of circular cross-section varies uniformly from a cross section 2D to D. If extension of the bar is calculated treating it as a bar of average diameter, then the percentage error will be (a) 10 (b) 25 (c) 33.33 (d) 50
The radius and height of a right cylinder are measured at 2.9m and 1.6m respectively with a maximum error of 2%. Compute the resulting percentage error measured in the surface area of the cylinder by the formula S = 2nr2 + 2nrh. Assume the value of n is exact for calculation.
An EDM instrument has a purported accuracy capability of +(2 mm + 2 ppm). The estimated error for both instrument and target miscentering errors is +1.5 mm. Part A What is the precision of measurement, in terms of parts per million, for a line length of 52.000 m? Express the answer in parts per million to three significant figures. E = Submit Part B E = Submit Part C |Π| ΑΣΦ ↓↑ Request Answer E = What is the precision of measurement, in terms of parts per million, for a line length of 510.000 m? Express the answer in parts per million to three significant figures. VE| ΑΣΦ | | vec Request Answer www vec 5 P ? www ? ppm What is the precision of measurement, in terms of parts per million, for a line length of 4890.000 m? Express the answer in parts per million to three significant figures. IVE ΑΣΦ ↓↑ vec ? ppm ppm
I Review the body relative to the cross-section. Consider the pipe assembly shown in (Figure 1). Neglect the weight of the pipe. Take F1 = {200 i – 200 j – 200 k} N and F2 = {200 i + 500 j} N. Express your answers using three significant figures separated by a comma. %3D Vy, Vz = -300,200 N Submit Previous Answers Correct Part C Determine the x, y, and z components of internal moment acting at a section passing through point B on the left part of the body relative to the cross-section. Figure 1 of 1 Express your answers using three significant figures separated by commas. vec Mg, My, M; = 400, – 300,200 N·m F, B Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining 1.5 m Provide Feedback Next >
QUESTION 1 If the accidental error is estimated to be +0.0079 for each of 33 separate measurements, what is the total estinated error. State your answer to three decimal places. It is understood that this answer is plus or minus.