The element shown in Figure 2 is from a structure which is under combined loading. For the following state of stress, use Mohr's circle to: a) Determine the principal stresses. b) Determine the principal plane. c) Determine the maximum in-plane shearing stress. d) Determine the normal stress corresponding to the maximum shearing stress (average stress).

The element shown in Figure 2 is from a structure which is under combined loading. For the following state of stress, use Mohr's circle to: a) Determine the principal stresses. b) Determine the principal plane. c) Determine the maximum in-plane shearing stress. d) Determine the normal stress corresponding to the maximum shearing stress (average stress).

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.19P: During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as...

See similar textbooks

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the \y axes, that is, determine crv, tr(_, and t, Show the results on a sketch of an clement oriented at B .
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and = -120 psi, as shown by the plalte-stress element in the figure part a. Determine the normal and shear stresses acting on a seam oriented at an angle 01300 to the element, as shown in the figure part b. Show these stresses on a sketch of an element having its sides parallel and perpendicular to the seam.
A specimen used in a coupon test is shown in the figure. The stresses on element A are known to be sy= -1500 psi. Use Mohr’s circle to: (a) Find the stresses acting on the element oriented at an angle ?? = -35°. (b) Find maximum normal and shear stresses and show them on sketches of properly oriented elements.
Q1. For the given cube below, complete the following: 1.find the center, radius (R), principal normal stresses (σ and σ3), max shear stress (Tmax) and draw the Mohr's Circle. 2. Find the stresses on a plane that is rotated 60° clockwise from the horizontal plane. 6PSE IPSF 10pst 60⁰ TOPST IPSF 6PSF
Angle 1 Tyx Tyx Figure 1 Point A- x-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: a) From basic priciples determine the stresses on the plane of the indicated angle 1-30°, Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle. c) Using a Mohr circle, determine and draw the maximum stress block of the in-plane maximum shear and principle stresses. d) Determine the stresses and orientation of the stress block where the normal stress is zero. Make use of the stress transformation equations. e) Determine the values of absolute maximum shear stress and corresponding normal stress.
The state of plane stress shown occurs at a critical point of a metal machine component. As a result of several tensile tests, it has been found that the tensile yield strength is Fy for the grade of metal used. Determine the ratio of OT/ OH shown in the figure, using the maximum-shearing-stress criterion (Tresca Hexagon). (Using Mohr circle method to calculate principle and average stresses) OX TXy Mpa Mpa Mpa MPa ob σy тху 90 -60 45 310 dy OX x Sx=Sx Sy=sy txy=txy Fy=Yield Strength Answer