The diameter of side of a pump is 6 inches and that of the intake pipe is 8 inches. The pressure gauge at discharge reads 30 psi and vacuumed gauge at intake reads 10 inches of Hg. If Q=3cfs of water and the brake horsepower is 35. Find the efficiency of the pump. There are no loss

Q: Water flowing in a horizontal pipe is at a pressure of 1.40 x 10^5 Pa at a point where its cross…

A:

Q: A pressure relief valve has a power loss across the valve is 11.6 x 10 MJ/sec and flow rate of 5.22…

A: If a constant static back-pressure is greater than atmospheric, the set pressure of the pressure…

Q: smooth steel pipe of diameter 500 mm and length 850 m carries water at the rate of 0.05 m3/sec. Find…

A:

Q: nlet and throat diameters of a horizontal venturimeter are 350 mm and 150mm respectively. The liquid…

A:

Q: A pipe that is 200 mm in diameter (point 1) diverges into segments 150 mm (point 2) and 90 mm (point…

A:

Q: A compressor delivers 180 scfm of air through a 3/4-in schedule 40 pipe at a receiver pressure of 85…

A:

Q: (b) A venturi meter with diameter at inlet D, and throat diameter D2, is used for measuring the flow…

A:

Q: A centrifugal pump draws water from a sump through a vertical 15 cm pipe. The pump has a horizontal…

A:

Q: is being drawn from a closed tank having a pressure of 70 kPa gage. The level of oil in the tank is…

A:

Q: A horizontal air duct reduces in cross-section area from 0.070 m^2 to 0.020 m^2.  Assuming no…

A:

Q: For the pipe system shown. Assume n = 0.013 for all pipes. Neglect minor losses. 1. Compute the…

A: Head loss in a pipe is given by the formula hf = flv22gd = 8 f l Q2π2 g d5Where f= n = 0.013…

Q: (Problem 3) A horizontal water pipe is reduced in size from 18 inches in diameter from point A to 6…

A:

Q: A venturimeter with 75 mm diameter throat is placed in a 150 mm diameter pipeline carrying water.…

A:

Q: 4. Brine (SG = 1.1, viscosity = 1.1cP) is pumped at a rate of 45 ft^3/min (ID = 2.5in) from large…

A: Specific gravity of Brine, SG=1.1Viscosity of brine, μ=1.1 cP=1.11488.1639lb/ft.sec=7.3916*10-4…

Q: Water is transported in a pipe, at an average flow rate of Q = 50 L/s. Calculate the pressure…

A: Given: The flow rate, Q = 50 l/s The energy added by the pump, H = 10 m

Q: Q1: Water flows in a circular pipe. At one section the diameter is 0.3 m the static pressure is 260…

A:

Q: A Kaplan turbine develops 1500 kW under a head of 6 m. The turbine is set 2.7 m above the tailrace…

A:

Q: Note: Unless otherwise stated, take the density of water to be p = 1000 kg/m³ and atmospheric…

A: Please refer to the detailed solution given below, Answers - (a) Pump Power P = 8.1357 KW (b)…

Q: A liquid (SG = 0.562) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are…

A:

Q: Question 7 A liquid, with a density of 850 kg/m3 , is flowing downwards through a vertical pipe…

A:

Q: The venturi meter experiment observation readings are 319 mm, 283 mm, and the flow meter reads 178…

A:

Q: Determine the mechanical efficiency of a centrifugal water pump which has an input of 3.6 Hp if the…

A: Given  Input = 3.6 HP Suction size =8 inch discharge size =6 inch handles =150 gpm at 150oFSuction…

Q: A pipe of 180mm bore is delivering water at a rate of 8250dm3/min at a pressure 800kN/m2. It…

A:

Q: Suppose it takes ½ hour to fill a 16 ft x 32 ft x 7 ft swimming pool from a 2.0 in. diameter pipe,…

A: Time required to fill the swimming pool, t=12hr=12*3600 seconds=1800 secVolume of the swimming pool,…

Q: A pump is used that has a Power Pb= 40HP and works with an efficiency of 85% to drive a flow rate Q…

A:

Q: Please see attachment.

A:

Q: A certain turbine has a capacity of 45 ft³/s. 3ft³/s is lost during the flow. The tailwater is 14 7…

A:

Q: specific gravity of 0.80 and a viscosity of 27 [p] is transported at 200 [m^3/h] using a 10"…

A:

Q: The air is measured at 48 deg. C and 511mm Hg. The duct diameter is 553 mm while the discharge…

A:

Q: Seven hundred gpm of water are being discharged by a centrifugal pump 5 ft. above the pump inlet.…

A:

Q: A 2-inch diameter hose is conveying water at a flow rate of 20 gpm from point A to point B. The…

A: Given: Pressure at point A: →PA=40 psi=144×40=5760 lbf/ft2 Elevation at point A from mean sea level:…

Q: best fits between the options of the graph A, B, C, D and F,

A: Given:- Static head= 85 Capacity= 195   To Find:- Best impeller & Expected Power consumption

Q: The pressure after the pump in a 6-inch inside smooth pipe conducting water is 20 psia. The water is…

A:

Q: The oil tank for the hydraulic system of figure below is air-pressurized at 10 psig. The inlet line…

A: Given Data The pressure of air is:P1=10psig=1440 lb/ft2 The datum of inlet line to the pump…

Q: Water is pumped through 750 ft of 6-inch nominal diameter Schedule number 40 pipe. The difference in…

A:

Q: shower head in your apartment needs to have water come out with a speed of 9.6m/s. The shower head…

A: The schematic diagram is Given data, V3 = Velocity of water at shower head = 9.6 m/s n = No of…

Q: (1) Inlet sudden contraction H Valve (2) Sudden expansion Bends Exit Find out the following? Case 1:…

A: Head loss of hydraulic system is divided into two main categories: Major head loss – due to…

Q: Water is flowing through a horizontal tube According to the figure . It's diameter at 2 points are…

A:

Q: In Figure 1, water flows vertically downwards in a trococonical tube. Diameters are D1=40 in ;…

A:

Q: Water at 60 F is flowing in an 18-inch Schedule 80 steel pipe. Find the wave speed for the system.…

A:

Q: A large tank is partly filled with oil (s.g.= 0.85), the air space above being under pressure. A 50…

A:

Q: 1. Atmospheric pressure is about 80 kPa (absolute). Water pressure at the base of a water tower is…

A:

Q: A pipe 50 cm in diameter carries water (l0°C} at a rate of 0.5 m 3 / s. A pump in the pipe is used…

A:

Q: Oil is flowing through the venture meter shown in the figure. The water velocity in the main pipe of…

A:

Q: 5. [Ch4 – 3] For the hydraulic system (shown in figure), the following data are given: • The pump is…

A: Given: Q=2×10-3 m3/sd=25×10-3 m

Q: If two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet.…

A:

Q: Figure 4 shows the hydraulic circuit to perform work with the piston. The pump extracts oil (sg…

A:

Q: The diameter of the discharge pipe is 7in and that of intake pipe is 9in. The pressure gage at…

A:

Q: A venturi meter with diameter at inlet D1, and throat diameter D2, is used for measuring the flow of…

A:

Q: a) In a vertical pipe carrying water, see Figure 3, pressure gauges are inserted at points A and B…

A: Data given- Q = 0.02 m3/s  dA  = 0.15 m  dB  = 0.075 m  Pb - Pa = 14715 N/m2

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.