The diameter of pipe (cast iron) is constant equal to 15 cm and total length of pipe is 180 m. It is desirable that the exit velocity of water to the garden should not exceed 5 m/sec and water is at atmospheric pressure and temperature is 20°C. Solve the following cases: Case 1 The gardener is planning to open the valve for 3 hours daily. Calculate the followings: a) How much volume of liquid can be drawn from reservoir in a day? b) How much total irreversible head loss will be occurred in the system?

The diameter of pipe (cast iron) is constant equal to 15 cm and total length of pipe is 180 m. It is desirable that the exit velocity of water to the garden should not exceed 5 m/sec and water is at atmospheric pressure and temperature is 20°C. Solve the following cases: Case 1 The gardener is planning to open the valve for 3 hours daily. Calculate the followings: a) How much volume of liquid can be drawn from reservoir in a day? b) How much total irreversible head loss will be occurred in the system?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. A tank and piping system are shown below. The total length of PVC pipe is 2500 ft and discharges water into the atmosphere. The pipeline has an open globe valve and four threaded elbows; h1 = 10 ft and h2 = 45 ft." a. If the discharge is 0.5 cfs, what NPS should be used for the PVC pipe (ks = 0.00006 inch). b. What is the pressure at A, the midpoint of the pipeline? c. Draw the EGL and HGL. h2 Water T = 10°C (50°F) Globe valve
The steel pipe shown carries water from the main pipe A to the reservoir and is 2 inch in diameter and 240 ft long. What must be the pressure in A to provide a flow of 45 gpm? Clevation K00 t Water 7 50 F Open globe valve 90 bends (threaded)- Elevtion 20 fr 2 in galvanizcd pipe
(Flow through Single Pipes). Determine the flow in each pipe and the pressure at the junction node, D. Assume elevation at Node, D to be 328 feet and friction factor, f, of 0.02 for all pipes. [NOTE: This is a three-part problem]. A B Elevation (ft) Length (ft) 19,680 Diameter (ft) Reservoir Pipe Part A) A 656 AD 3.28 В 590 BD 13,120 2.5 558 CD 29,520 2.5 19,680 13,120 Part B) A 656 AD 3.28 В 574 BD 3.28 CD 29,520 19,680 19,680 492 2.5 Part C) A 656 AD 3.28 В 590 BD 3.28 492 CD 19,680 3.28
b) The old Hydraulics laboratory in Mechanical Engineering used a roof tank to supply apparatus with water at a nearly constant head. The water was collected in an under floor sump, and then pumped back to the roof tank after the experiment. The flow rate was 10 litre s1. The tank was 6m above the sump, and the length of the pipe route was 15 m. The old 6" pipes are now heavily corroded (k = 7.5 mm). The old pump has been scrapped. What head AH would be specified for a pump to restore the system using the old pipes? What would the pump power be? If the pipes were replaced with 150 mm diameter PVC pipes, what pump AH would be required? ROOF TANK 6m PUMP SUMP
At night, water is pumped from a treatment plant reservoir through distributing piping to an elevated storage tank. Assume no other withdrawals from the system. The water surface in the supply reservoir is at 3m elevation, the lift pump elevation is 6m, the water elevation in the elevated tank is 42m. The pipe network maybe considered equivalent to 1500m of 250mm diameter. Use C=100. There is a supply of 60 Liters/sec. to the tank. a. Compute the head loss of the 250mm diameter pipe. b. Compute the pump discharge pressure required to supply a flow of 60L/s to the tank, c. Compute the slope of the energy gradient
Oricul Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow rate in each pipe. The pipes characteristics are given as follows: Pipe L (m) D (mm) f A 610 152 0.020 B 488 102 0.032 C 1220 203 0.024 Good Luck -re (2) Water qure (3) EL=7om A B EL-15m
oll, s = 0.80 kerosene,s = 0.82 A manomoter is used to moasuro tho s = 0.0012 pressure of air in shown. Solve the pressure at point A given the following hoights: the pipe as Air = 0.35 m,h2 = 0.38 m, h, = 0.20 m, %3D h4 = 0.50 m, hs = 0.10 m, h6 = 0.30 m hz hy h3 ho Water Mercury Mercury
Q2: Find the diameter of the pipe 2 in the loop shown below which contains two pipes connected in parallel. Q = 10 I/s, V3= 1 m/s, A3 = 0.03 m', CHw=100, d,=150mm, L1 =1500 m, L2 =2000m. di:150 1 V-123 2. 63 21:2000m P: 2.78Td dz?? 74 7.
The figure below shows a fabricated assembly made from three different sizes of standard steel tubing listed in Appendix G.2. The larger tube on the left carries 0.075 m3/s of water. The tee branches into two smaller sections as shown. Reducing tee Flow 100-mm OD x 3.5-mm wall steel tube - 160-mm OD x 5.5-mm wall steel tube - 50-mm OD x 1.5-mm wall steel tube Required If the velocity in the 50-mm tube is 10.00 m/s, what is the velocity in the 100-mm tube to the nearest 1000th?
Trace the characteristic curve of the pipe shown in the Figure below. Data are: total length of pipe L= 80 m; equivalent length Leq= 40 . For simplicity, assume all piping is 40S in steel. The pumped fluid is water at 20 °C.
Determine the pressure at the center of the pipe from the piezometer shown. 200mm WATER 75mmØPIPE
apparatus with water at a nearly constant head. The water was collected in an underfloor sump, then pumped back to the roof tank after the experiment (see Fig. Q4 below). The flowrate was 10 litres s'. The tank was 6 m above the sump, and the length of the pipe route was 15 m. The old 6" (152.4 mm) pipes are now heavily corroded (k = 7.5 mm). The old pump has been scrapped. Evaluate and calculate: a) the head AH that would be specified for a pump to restore the system using the old pipes. b) the pump power value based on the head AH of pump calculated in (a). c) the required pump AH if the pipes were replaced with 150 mm diameter PVC pipes. ROOF ΤΑNK 6m ) PUMP SUMP Fig. Q4