The design of a city water supply is shown below. Pipe 1 is 300 mm diameter and 900 m long, Pipe 2 is 200 mm diameter and 387 mm long and pipe 3 is 200 mmdiameter and 700 m long. The roughness coefficient for all pipes is 0.011. Determine the headloss in pipe 1 in m.EL 160 MAEL 150 MB123EL 140 MC

Answered: Image /qna-images/answer/5c5b01a2-166d-4eee-8219-1a97933e5c8b.jpg

The design of a city water supply is shown below. Pipe 1 is 300 mm diameter and 900 m long, Pipe 2 is 200 mm diameter and 387 mm long and pipe 3 is 200 m diameter and 700 m long. The roughness coefficient for all pipes is 0.011. Determine the headloss in pipe 1 in m. EL 160 M A EL 150 M B 1 2 3 EL 140 M C

The design of a city water supply is shown below. Pipe 1 is 300 mm diameter and 900 m long, Pipe 2 is 200 mm diameter and 387 mm long and pipe 3 is 200 m diameter and 700 m long. The roughness coefficient for all pipes is 0.011. Determine the headloss in pipe 1 in m. EL 160 M A EL 150 M B 1 2 3 EL 140 M C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A municipality wants to determine the flow rate into the plant based on pipe size, elevation difference, and assumed roughness, for the water supply reservoir is shown in the figure below. The pipe is an old 4-inch diameter Cast Iron with a Hazen Roughness coefficient of 100 & 223 feet long. The difference in elevation is 62 feet. The pipe has a strainer at the entrance (k-1.9), a valve (k=8.6), a check valve (k = 2:7) and 3- 90° bends (k-0.83). The flow exits into a receiving pond at the WTP. Provide the flow rate in Gallons Minute. per WTP Az
Oricul Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow rate in each pipe. The pipes characteristics are given as follows: Pipe L (m) D (mm) f A 610 152 0.020 B 488 102 0.032 C 1220 203 0.024 Good Luck -re (2) Water qure (3) EL=7om A B EL-15m
Civil Engineering !! I need the correct answer Water flows through two different pipes A and B of the same circular cross- section but at different flow rates. The length of pipe A is 1.0 m and that of pipe B is 2.0 m. The flow in both the pipes is laminar and fully developed. If the frictional head loss across the length of the pipes is same, the ratio of volume flow rates QB/QA is _(round off to two decimal places)
Water flows through a 300mm diameter pipe at a velocity Of 3.00 m/s. Determine the weight flow rate in N/s. Do not write the unit. You will only jnput the numerical answer in the space provided. Unit of the Correct Answer: N/s O 9810.000 O 2,080.284 O 8829.000 1202.284
Civil Engineering Water flows through two different pipes A and B of the same circular cross- section but at different flow rates. The length of pipe A is 1.0 m and that of pipe B is 2.0 m. The flow in both the pipes is laminar and fully developed. If the frictional head loss across the length of the pipes is same, the ratio of volume flow rates QB/QA is _(round off to two decimal places)
1) The figure shows a conduit made of 1 std type K drawn copper tubing that conveys acetone at a flow rate of 1.33x10 m³/s. All fittings are soldered; the gate valve is fully open. (a) calculate the pressure drop through the system using minor-loss values. (b) Calculate the pressure drop through the system using equivalent length values. Compare the results. The total length of tubing is 9.15 m and the conduit is in a horizontal plane.
A pipeline 200 meters long delivers water from an impounding reservoir to a service reservoir with the difference in water levels of 20 meters. The pipeline of commercial steel is 400 mm in diameter. It has two 90 degree flanged elbows, a check valve, and an orifice (K_m= 2.5). Determine the flow through the pipe. Use a water temperature of 20 degrees Celcius.
A 30m long, 20mm diameter steel pipe is used to drain an oil tank determine the discharge when the oil level in the tank is 4m above the exit of the pipe. Neglect minor losses, (assume f = 0.12)
Three pipes of 400 mm, 300 mm and 200 mm diameters have lengths of 400 m, 300m, and 200 m respectively. They are connected in series to make a compound pipe. The endsof this compound pipe are connected with two tanks whose difference of water levels is 16 m. If co-efficient of friction for these pipes is same and equal to 0.005, determine the dischargethrough the compound pipe neglecting first the minor losses and then including them. faaaasttt
For this diagram of an industrial pressure washer system, x = 2 ft, y = 5 ft, z = 9 ft, Q = 3.4 ft3/s, and the hose diameter is 3 in. Assuming a head loss of 4 ft is derived over the distance from point 2 to the jet, what is the pressure at point 2 if the jet from the nozzle is 1 in. in diameter? Assume a = 1.0 throughout. O 535164 psi O 372383 psi O 2586 psi ○ 4996 psi 2 Z Nozzle
Two pipes are connected in parallel. One pipe is twice the diameter of the other and three times long. Assume that f in the larger pipe is 0.010 and f in the smaller is 0.014. Determine the ratio of the discharges of the two pipes.
Q2) i Neglecting minor losses in the pipe, determine the flows in the pipes and 0 the pressure heads at the nodes (kinematic viscosity= 1.13x104m?¥s) F E n I I 30 Data Pipe Ab BC O DE EF AF BE Lengeh (m) 600 600 200 600 600 200 200 Diameter (wm) 250 150 100 150 150 200 100 Roughness size of all pipes = 0.06 mm Pressure head elevation at A = 70 i o.d. Elevation of pipe nodes A 5 c D L ® 028 0 20 2 2