The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner steel core (2). The bronze sleeve has an outside diameter of 35 mm, an inside diameter of 20 mm, and a shear modulus of G1 - 41 GPa. The solid steel core has a diameter of 20 mm and a shear modulus of G2 = 80 GPa. Assume L- 430 mm. The composite shaft is subjected to a torque of T- 990 N-m. Determine (a) the maximum shear stresses in the bronze sleeve and the steel core. (b) the rotation angle of end B relative to end A. (1) L. B

The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner steel core (2). The bronze sleeve has an outside diameter of 35 mm, an inside diameter of 20 mm, and a shear modulus of G1 - 41 GPa. The solid steel core has a diameter of 20 mm and a shear modulus of G2 = 80 GPa. Assume L- 430 mm. The composite shaft is subjected to a torque of T- 990 N-m. Determine (a) the maximum shear stresses in the bronze sleeve and the steel core. (b) the rotation angle of end B relative to end A. (1) L. B

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2DP

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
The composite shaft shown in the figure consists of a bronzesleeve (1) securely bonded to an inner steel core (2). The bronze sleeve has an outside diameter of 25 mm, an inside diameter of 20 mm, and a shear modulus of G1 = 45 GPa. The solid steel core has a diameter of 20 mm and a shear modulus of G2 - 83 GPa. Assume L - 470 mm. The composite shaft is subjected to a torque of T-970 N-m. Determine a) the maximum shear stresses in the bronze sleeve and the steel core. b) the rotation angle of end B relative to end A. Answers: (a) TI = MPa T2 = MPa (b) PRIA = rad
The composite shaft shown consists of a 2 mm thick steel jacket (G=77 GPa) bonded to a 50 mm diameter aluminum core (G=26 GPa). Knowing that the ultimate shear strength of the steel and the aluminum is 145 and 55 MPa, respectively, determine the maximum possible torque to be applied to A such that the composite shaft does not fail. aluminum core A steel jacket
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m 5KN 0.6m A 20KN 3) What is the deformation &cn in mm? A=800 mm? A=1,200 mm²
The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner steel core (2). The bronze sleeve has an outside diameter of 35 mm, an inside diameter of 30 mm, and a shear modulus of G2 - 45 GPa. The solid steel core has a diameter of 30 mm and a shear modulus of G2 - 85 GPa. Assume L - 380 mm. The composite shaft is subjected to a torque of T- 800 N-m. Determine (a) the maximum shear stresses in the bronze sleeve and the steel core. (b) the rotation angle of end B relative to end A. (1) L B Answers: MPa (a) TI = MPa rad (b) PBIA =
An aluminum tube is fastened between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. For Bronze: Allowable stress = 120 MPa, EB = 83,000 MPa For Aluminum: Allowable stress = 120 Mpa, EA = 70,000 MPa For Steel: Allowable stress = 120 MPa, Es = 200,000 MPa Assume that the assembly is suitably braced to prevent buckling. Maximum overall deformation should not exceed 2mm. a) Give the value of the force acting on the bronze so as not to exceed allowable stresses and deformation. b) Give the value of the force acting on the aluminum so as not to exceed its allowable stresses and deformation. c) Give the value of the force acting on the steel so as not to exceed its allowable stresses and deformation.
Problem 1.5-2 A bar of length 2.0 m is made of a structural stoel having the stres-strain dingram shown in the figure. The yield stresa of the steel is 250 MPa and the slope of the initial lincar part of the stress-strain curve (modulus of elasticity) is 200 GP. The bar is loaded axially until it eklongates 6.5 mm, and then the load is removod. How does the final length of the bar compare with its orig- inal length? Hint: Ue the concepts illustrated in Fig. 1-36h) MP 300 200 100 0.002 0.004 0.006
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. Determine the displacement of end A with respect to end D. The cross-sectional area and modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C 16 kN 8 KN 9 KN 450 mm- 16 KN C 300 mm- Section AB is Aluminum with Young's modulus of 70 GPa and an area of 63 mm². Section BC is Copper with Young's modulus of 126 GPa and an area of 87 mm². Section CD is Steel with Young's modulus of 200 GPa and an area of 39 mm. The displacement of end A with respect to end Dis Note: Please enter your answer with three significant digits after the decimal point. .mm 8 KN 400 mm- 7 KN
An aluminum alloy [E = 73 GPa; v = 0.33; a= 23.0 x 10-6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 250 mm, a cross-sectional area of A = 6900 mm², and a length of L = 5.9 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by AT = 50°C, the longitudinal normal strain in the plate is found to be 2400 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Ad. L Answer: (a) P = i (b) Δd = KN mm
An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m 10KN 0.8m 0.4m 5KN 0.6m What is the deformation 8Rc in mm? Al 20KN A=800 mm? A=1,200 mm²
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X