The block A and attached rod have a combined mass of 58 kg and are confined to move along the guide under the action of the 846-N applied force. The uniform horizontal rod has a mass of 24 kg and is welded to the block at B. Friction in the guide is negligible. Compute the bending moment Mexerted by the weld on the rod at B. The bending moment is positive if counterclockwise, negative if clockwise. 846 N Answer: M- 68 B 2.3 m- N-m

The block A and attached rod have a combined mass of 58 kg and are confined to move along the guide under the action of the 846-N applied force. The uniform horizontal rod has a mass of 24 kg and is welded to the block at B. Friction in the guide is negligible. Compute the bending moment Mexerted by the weld on the rod at B. The bending moment is positive if counterclockwise, negative if clockwise. 846 N Answer: M- 68 B 2.3 m- N-m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.72P

See similar textbooks

Similar questions

Pin A, which connects the 200-kg steel beam with the center of gravity at G to the vertical column, is welded both to the beam and to the column. To test the weld, the 70-kg man loads the beam by exerting a 300-N force on the rope which passes through a hole in the beam as shown. Calculate the moment supported by the pin. Express your answer in units of kN-m. A Welded pin 1200 mm Go -600 mm 300 mm
the table lamp consists of two uniform arms, each weighing 4N, and a 10 N bulb fixture. if angle is 16 degrees calculate the couple CAthat must be supplied by the friction in joint A.
A 150-N force is applied to the foot-operated air pump. The return spring Sexerts a 2.6-N•m moment on member OBA for this position. Determine the corresponding compression force Cin the cylinder BD. If the diameter of the piston in the cylinder is 41 mm, estimate the air pressure generated for these conditions. State any assumptions. Enter a positive number for the compression force C. 20 135 10 150 N 140 B 90 130 200 -55- Dimensions in millimeters
Find the force P required to pull the 40-kg homogeneous roller with radius 720mm over the 90-mm curb.
2.0 m 100 kg 2.0 m 0.5 m 1.5 m 1.5 m The pulley at E is frictionless. Point B is a pinned connection; support A is a fixed support. The pin at C is in a smooth slot. s in: Determine the magnitude of of the x-component of the reaction force at A, Ax= N. Determine the magnitude of of the y-component of the reaction force at A, Ay= N. Determine the magnitude of of the external moment applied at A, MA= Nm. O O :
Determine the reactions ( forces and moments) at the journal bearings A,B, and C for the loading shown on the pipe.
A portion of the shifter mechanism for a manual car transmission is shown in the figure. For the 8.7-N force exerted on the shift knob, determine the corresponding force P exerted by the shift link BC on the transmission (not shown). Neglect friction in the ball-and-socket joint at O, in the joint at B, and in the slip tube near support D. Note that a soft rubber bushing at D allows the slip tube to self-align with link.
Calculate the vertical reaction force and reaction moment at the point A
The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (You can disregard the plot, I only need a, b, c, and d)
The beam consists of two bars connected by a pin at B. Neglecting the weight of the beam, compute the support reactions at A.
The needle-nose pliers are used to either cut objects at location A or grip objects at location B. Compute (a) the cutting force at A and (b) the gripping force at B in terms of the applied force F. Determine the magnitude of the pin reaction at O in both cases. Neglect the effects of the slight opening of the jaws to accommodate the gripped items.
The jib crane is designed for a maximum capacity of 9 kN, and its uniform I-beam has a mass of 260 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.4 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 1.6 m? (b) What is the value of R when x = 3.2 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 32° x m 9 KN 1.0 m 2.6 m Questions: (a) If x= 1.6 m, R= i (b) If x= 3.2 m, R = i (c) The minimum value for R = i (d) The pin should be designed to hold i KN KN kN at x = i kN.