The bar is connected to the support using a pin having a diameter of d =lin. Ifthe allowable tensile stress for the bar is (o,)low = 20ksi , and the allowable bearing stressbetween the pin and the bar is (0,)allow= 30ksi , determine the dimension w and t so thatthe gross area of the cross section is wt = 2in² and the load P is a maximum. What is thismaximum load? Assume the hole in the bar has the same diameter as the pin. (Hint: Usethe prjjected area whenj calculating the bearing stress.)tdw/2w/2

Answered: Image /qna-images/answer/a228a797-3d30-4ce5-96a6-cc38daea6bf8.jpg

The bar is connected to the support using a pin having a diameter of d =lin. If the allowable tensile stress for the bar is (o,),allow = 20ksi , and the allowable bearing stress between the pin and the bar is (o,)llow = 30ksi , determine the dimension w and t so that %3D the gross area of the cross section is wt =2in? and the load P is a maximum. What is this maximum load? Assume the hole in the bar has the same diameter as the pin. (Hint: Use the projected area when calculating the bearing stress.) d- w/2 w/2

The bar is connected to the support using a pin having a diameter of d =lin. If the allowable tensile stress for the bar is (o,),allow = 20ksi , and the allowable bearing stress between the pin and the bar is (o,)llow = 30ksi , determine the dimension w and t so that %3D the gross area of the cross section is wt =2in? and the load P is a maximum. What is this maximum load? Assume the hole in the bar has the same diameter as the pin. (Hint: Use the projected area when calculating the bearing stress.) d- w/2 w/2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the allowable tensile stress for the bar is 1st2allow = 21 ksi, and the allowable shear stress for the pin is tallow = 12 ksi, determine the diameter of the pin so that the load P will be a maximum. What is this load? Assumethe hole in the bar has the same diameter d as the pin. Take t = 1 4 in. and w = 2 in.
2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
The horizontal bar shown is pinned at O and is supported with a helical springat L1 from O. L1=2m, L2=1m. The spring has 30 turns and the diameter of the wire usedis 20mm. The diameter of the spring is 125mm. Modulus of Rigidity = 83GPa. Determine the shear stress of the helical spring loaded as shown if w = 25kN/m.
The vertical shaft with a diameter of d = 20 mm is supported by a thrust collar that rests on a 21-mm-thick plate. The thrust collar is 16-mm thick. Assume that the load P causes a compressive stress of 190 MPa in the shaft. If the bearing stress between the thrust collar and the plate is limited to 35 MPa, determine the minimum outer diameter Dcollar that must be used for the thrust collar. Thrust collar area Plate Thrust collar d Dcollar
If the allowable tensile stress for the bar is (o,) allow = 21 ksi, and the allowable shear stress for the pin is Tallow = 12 ksi, determine the diameter of the pin so that the load P will be a maximum. What is this load? Assume the hole in the bar has the same diameter d as the pin. Take i = in. and w = 2 in.
Find the stress in the rod having a diameter of 20 mm, subjected to 10 kN force. If the material of the rod is steel (E = 200 GPa), what is the change in length of the rod?
The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap D= 4 mm between the lower end of the left rod and its pin support at C. Compute the stress in the left rod after its lower end is attached to the support. The cross-sectional areas are 300 mm2 for rod AC and 250 mm2 for rod BD. Use E= 200 GPa for steel. lo/0 0.75 m 1.5m 2 m ANSWER: MPa
The bar is connected to the support using a pin having a diameter of d = 1 in. If the allowable tensile stress for the bar is 1st2allow = 20 ksi, and the allowable bearing stress between the pin and the bar is 1sb2allow = 30 ksi,determine the dimensions w and t so that the gross area of the cross-section is wt = 2 in2 and the load P is a maximum. What is this maximum load? Assume the hole in the bar has the same diameter as the pin.
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 a. Determine how much the wire stretches when the horizontal force acts on the pole. 3 ft 30 D 2.5 kip 4 ft B b. Determine the change in the wire's radius c. At what angle is the principal stresses on pole BC? Use Mohr's Circle. d. What is the principal stress in pol BC? Use Mohr's Circle e. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. f. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) g. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. h. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)
5. The hanger is supported using the rectangular pin. Determine the magnitude of the allowable suspended load P if the allowable bearing stress is b,allow = 220 MPa, the allowable tensile stress is at,allow = 150 MPa, and the allowable shear stress is Tallow = 130 MPa. Take t = 6 mm, a = 5 mm and b = 25 mm. 75 mm 37.5 mm 20 mm 10 mm 37.5 mm
X A purse hook is used to hang a handbag from the edge of a table with L = 50 mm. If the cross section at a-a has a diameter of d = 3 mm and the hook is supporting a purse with a mass of 3 kg, determine the normal stress profile. For what value of y (using the coordinates pictured for section a-a) with the normal stress be zero. If it is never zero enter "nde" for "not defined". N -L→ a. a AB C Follow sign convention that tension is positive and compression is negative. Normal stress at point A, σA= MPa Normal stress at point B, σB = MPa Normal stress at point C, σc = MPa y position where normal stress equals zero = mm Section a-a d
Q: The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A,B,C, and D exert only vertical forces on the beam, determine the required diameter of the bolt at B and the required outer diameter of its washers if the allowable tensile stress for the bolt is ot allow = 150 MPa and the allowable bearing stress for the wood is ob allow = 28 MPa. Assume that the %3D hole in the washers has the same diameter as the bolt. 2 kN 3 kN 1.5 kN -2 m--1.5 m--1.5 m--1.5 m--1.5 m- 2 m bolt washer