The 50-kg homogenous smooth sphere rests on the 30° incline A and bears against the smooth vertical wall. Calculate the contact forces at A and at B, label as RA and RB respectively, using (a) triangle method (b) Component method: force equations (1st condition of equilibrium) (c) 1st and 2nd conditions of equilibrium В 30° А

The 50-kg homogenous smooth sphere rests on the 30° incline A and bears against the smooth vertical wall. Calculate the contact forces at A and at B, label as RA and RB respectively, using (a) triangle method (b) Component method: force equations (1st condition of equilibrium) (c) 1st and 2nd conditions of equilibrium В 30° А

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SOLVE THE PROBLEM USING DOUBLE INTEGRATION METHOD Problem II. The midpoint B of the steel cantilever beam ABC is supported by a vertical aluminum rod. Find the maximum allowable value of the applied force P if the stress in the rod is not to exceed 120 MPa. Use Est = 200 GPa, I = 50 x 10 mm4 for the beam, Eal = 70 GPa, and A = 42 mm² for the rod. 5 m 2 m Aluminum -Steel 2 m C
From the previous problem, determine the shear stress 30 mmabove the neutral axis.
The 43-kg homogeneous smooth sphere rests on the 20° incline A and bears against the smooth vertical wall B. Calculate the contact force at A and B. Assume = 20° Answers: FA = i FB = i B N N
Q\Discuss in detail the effect of the boundary condition in the Buckling of hollow shaft.
A rectangular-sectioned beam of 75 mm x 50 mm cross-section is used as a simply supported beam and carries a uniformly distributed load of 500 N/m over a span of 3 m. The beam is supported in such a way that its long edges are inclined at 20° to the vertical. Determine: (a) the maximum stress set up in the cross-section (b) the vertical deflection at mid-span TakeE = 208 GN/m².
The steel tube seen below has an outer diameter do = 60mm and an inner diameter d, = 50mm. It is subjected simultaneously to torque T = 1.5kN-m and to axial load P = 205kN. Determine: (a) the maximum in-plane shear stress and its orientation, (b) the associated normal stress and (c) sketch both on a properly oriented element.
Figure Q1 shows a statically determinate plane truss subjected to a verticalconcentrated load at C and E. The truss is made using steel with Modulus of Elasticity is210 GPa, and the cross section area for all members are 30 mm2. Assuming P is the 10 and a is half of P, determine the vertical displacement at F. Thesolution can be based on Method of Conservation Energy or Method of Virtual Work.
30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
The 450N plate is attached to collars which may slide on the vertical rod. If the coefficient of static friction is 0.4 between both collars and the rod determine the maximum supporting force available from friction when F = 200N; a = 2.75m , b = 4.5m , c = 2m Show solution, the answer is 168.75
5. If the surface tension is 0.006 N/m, and the wetting angle is 6, calculate the surface tensic force acting on the circumference of this element in the vertical direction. Ans:
The cantilever beam is subjected to a concentrated load P. The cross-sectional dimensions of the rectangular tube shape are shown in the second figure. Assume b = 133 mm, d = 207 mm, y = 62 mm, yk = 37 mm and t = 6 mm. (a) Compute the value of Q that is associated with point H, which is located 62 mm above the centroid of the rectangular tube shape. (b) If the allowable shear stress for the rectangular tube shape is 117 MPa, determine the maximum concentrated load P that can be applied to the cantilever beam. Answers: (a) Q = (b) P = i i P Z mm³. kN. ун Ук H K b t (typ.)
The corners of the square plate are given the displacements indicated. Determine the average normal strains Px and Py along the x and y axes.