temperature difference of 85°C is impressed across a fiberglass layer of 13 cm ickness. The thermal conductivity of the fiberglass is 0.035 W/m °C. Compute the eat transferred through the material per hour per unit area.

temperature difference of 85°C is impressed across a fiberglass layer of 13 cm ickness. The thermal conductivity of the fiberglass is 0.035 W/m °C. Compute the eat transferred through the material per hour per unit area.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.73P: Estimate the R-values for a 5-cm-thick fiberglass board and a 2.5-cm-thick polyurethane foam layer....

See similar textbooks

Related questions

Q: Find the force in member HI

Q: 3. The rigid surface shown on the left side of the figure has a vertical section and an inclined…

Q: The truck shown is used to deliver food to aircraft. The elevated unit weighs 2350 lb with center of…

Q: A square hole is made in a circular lamina, the diagonal of the square is equal to the radius of the…

A: radius of circle= rTo determine:The shift in center of gravity

Q: 6. Select the correct statement: A) h stands for element height. B) h stands for hyperbolic element.…

A: D) h stands for element size.Explanation:In finite element analysis, h is commonly used to denote…

Q: 4. Green checkmark visible in this illustration means that: A) Results are ready for review. B)…

A: The green check mark in the illustration means that C. the meshed has passed the quality check.This…

Q: a) Sketch the thermal conductivity versus temperature from 0 to 1000K for silver. b) What is the…

A: To find:Sketch and explain the behaviour of dependence of thermal conductivity of silver with the…

Q: For given distributed loads, see figures below, determine resultant and moments around load ends…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

Q: Ice slurry is being transported in a pipe (k = 15 W/m K, D;= 0.025 m, Do= 0.085 m, and L = 5 m) with…

A: Ice slurry is being transported in a pipe;kpipe =15 W/m.KL= 5 mDi= 0.025 mDo= 0.085 mTi=…

Q: Hi could you also please give the solution to d, e, f

A: As per the guidelines we are subjected to solve only 3 sub parts at a time. Please repost the same…

Q: A pressure vessel is exposed to a combination of loads as shown below. The vessel (diameter 100 mm)…

A: Given data:To find:(a) The tension force P according to distortional energy theory.(b) The minimum…

Q: For a given transfer function, is there only one unique solution to convert it into state-space…

A: To elaborate on conversion of one unique solution to state space representation

Q: How many possibilities are there to represent the orientation of a frame (B) relative to a fixed…

A: Given:Fixed angle convention.To find:(a) Number of possibilities to represent the orientation of a…

Q: Consider the one-dimensional, incompressible flow through the circular channel shown. The velocity…

A: Given:Velocity at section 1:U(t)=U0 +U1 sinwtU0=20 m/sU1 =2 m2/sw=0.3 rad/sL=1 mR1= 0.2 mR2= 0.1…

Q: A drum of mass Ma and radius a rotates freely with initial angular velocity ωa0. A second drum with…

Q: The economiser of a steam boiler receives its feed water at 34.6°C and supplies the evaporator at a…

Q: A torque of 200 ft-lb is developed by a diesel engine when running at 1200 rpm and using 20lbs of…

A: To determine:1) Bore diameter.2) brake thermal efficiency.Given:torque developed is the speed of the…

Q: Consider the cross section of the beam shown where a = 0.8 in. The beam's centroid is located at…

Q: Determine the bending moment diagram and determine the magnitude of the pending moment when x = 1.75…

A: To calculate the bending moment and to draw the bending moment drawinggivenlength of the beam,…

Q: Given the system equipped with unitary feedback, whose direct branch transfer function is: (s + 4)…

A: To design a PID controller using the Ziegler-Nichols method, we need to follow the steps below: Step…

Q: The compound shaft shown in the figure consists of two steel [G = 80 GPa] pipe segments. The shaft…

A: Given Data:The modulus of rigidity of steel is..The outside diameter of segment 1 is..The wall…

Q: 5-14. The shelf supports the electric motor which has a mass of 15 kg and mass center at G. The…

A: The shelf supports the electric motor which has a mass of mm = 15 kg and mass center at G.The…

Q: The end rollers of bar AB are constrained to the slot shown. If roller A has a downward velocity of…

A: Given:To find:Tangential acceleration of roller B.

Q: Problem 2 Consider the two positions provided in the figure. (a) Using the graphical method to…

A: The problem you presented is a mechanical linkage system. Here is the step-by-step solution:Step…

Q: You have compressed liquid propane in a 5 ft³ closed rigid vessel at 6000 psia and 300 °F but for…

A: The initial state (State 1) of the propane is at 6000 psia and 300°F, and the properties at this…

Q: 3-137 For Problem 3-136 estimate the stresses at the inner and outer surfaces at section B- B,…

Q: Statics of Rigid Bodies (Write the COMPLETE Solutions and FBDs legibly. No long explanation needed.…

A: Given :To find: A. Determine the Moment of Inertia about the Xo and Yo axis (____ x10^6 mm4B.…

Q: Problem 4: Refer to the data below. Calculate the net present worth (NPW) of the project. Initial…

A: Initial cost= $35,000A= Annual benefits= $ 5,000n= Useful life= 10 yearsS.V= saving value= $10,000r=…

Q: Dry air at 270C flows with a velocity of 360 kmph in an adiabatic wind tunnel. The static pressure…

A: Given:To find:(a) Mach number.(b) Stagnation temperature.(c) Stagnation pressure.(d) Stagnation…

Q: A supply line that carries steam at 5MPa and 500°C is connected to a piston- cylinder device in…

A: Given, a piston- cylinder device with the following data.Initial Volume of steam, Initial pressure…

Q: A piston-cylinder device initially contains 1.0 kg of water at 30 o C and 2 MPa. The water is heated…

Q: The shaft shown below is made of AISI 1020 steel. Determine the most critical section, the principal…

A: Given d2=40mm=0.040m1st Considering the location of stress concentration 80mm from the…

Q: 1. For given distributed loads, see figures below, determine resultant and moments around load ends…

A: As all questions are different, according to our guidelines we are supposed to answer the first…

Q: QUESTION 1 An ideal gas undergoes isentropic expansion in a turbine from 520 0C. The initial…

A: To solve this problem, we will follow a step-by-step approach:The connection between temperature…

Q: Gear ratio of the epicyclic gear system discussion

A: The three major parts of an epicyclic gear system, sometimes referred to as a planetary gear system,…

Q: 2. Determine the moment projected by the force F in the above figure about point O. Express the…

A: F=5 kN%Matlab Script:clear,clc% i)ra=[ 0 0 12] % ra position vector [x-coordinate y-coordinate…

Q: The economiser of a steam boiler receives its feed water at 34.6°C and supplies the evaporator at a…

A: From steam table:The specific enthalpy of water at 34.6°C and 600 kPa is h1 = 145.507 kJ/kg.The…

Q: Q.1) The following truss has a pin support at A and a rocker support at G. Points A, B, C, D, E, F,…

A: The following truss has a pin support at A and a rocker support at G. Points A, B, C, D, E, F, G are…

Q: Discuss the different regimes of fretting using diagrams

A: Fretting is a particular kind of surface damage that develops when two materials are in contact and…

Q: Consider the given figure. 2 kN S S R Q SRQ Q P 0.8 m 0.8 m 0.8 m 0.8 m 0.8 m 0.8 m D EL G H I J Bo…

A: Given data:Find:The force in members CF, EF and EG.

Q: can you resolve?

A: Loop Closure Method :where ri" data-mce-style="display: inline-block; line-height: 0; text-indent:…

Q: mospheric pressure, water melts as the temperature increases from 270K to 280K because a. the…

A: The melting point of an object, water is the temperature at which it transitions from a solid phase…

Q: Figure 2 shows a built-up cross-section of a horizontal beam which has a maximum shear force of 100…

Q: A mass of 4 kilograms is attached to the end of a spring. A force of 8 N stretches the spring 80 cm.…

Q: Determine the particular solution for x. Show it can be put in the form (w.) ² * xp(t) = h 1 2 2 √√…

Q: A torque of magnitude T= 25,000 lb-in is applied to the end of a tank containing compressed air…

Q: Consider an oil flow of 14 m3/h in a long, straight and smooth pipe with diameter of 5 cm. What is…

Q: Problem 2: A piston, moving with a simple harmonic motion, has a velocity of 8 m/s, when it is 1…

A: The given data for this question are,

Q: A cantilevered beam of length L = 5 m is fixed at A. It has a moment of M = 35.0 kN⋅m applied at B…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

A temperature difference of 85°C is impressed across a fiberglass layer of 13 cm
thickness. The thermal conductivity of the fiberglass is 0.035 W/m °C. Compute the
heat transferred through the material per hour per unit area.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A metal rod 1 sq. in. in cross section and 6 in. long is heated at one end and cooled at the other. If the rate of heat input is 3 BTu/hr and the difference in temperature of the two ends is 2 deg. F, what is the coefficient of thermal conductivity in BTU/(hr)(ft²)(⁰F/ft)?
1.The height of the Washington Monument is measured to be 170 m on a day when the temperature is 35.0 °C. What will its height be on a day when the temperature falls to -10.0 ° C? Although the monument is made of limestone, assume that its thermal coefficient of expansion is the same as marble's. 2.How much taller does the Eiffel Tower become at the end of a day when the temperature has increased by 15 ° C? Its original height is 321 m and you can assume it is made of steel. 3.What is the change in length of a 3.00-cm-long column of mercury if its temperature changes from 37.0 ° C to 40.0 ° C, assuming the mercury is unconstrained? 4.How large an expansion gap should be left between steel railroad rails if they may reach a maximum temperature 35.0 ° C greater than when they were laid? Their original length is 10.0 m
A temperature difference of 85•C is impressed across a fiberglass layer of 13 cm thickness. The thermal conductivity of the fiberglass is 0.035W/m- •C. Compute the heat transferred through the material per hour per unit area.
A temperature difference of 85 •C is impressed across a fiberglass layer of 13 cm thickness. The thermal conductivity of the fiberglass is 0.035 W/m • -C. Compute the heat transferred through the material in kcal per hour per unit square meter area.
b) A steel pipe of 100mm bore and 7mm thickness transports steam at 260 °C. The pipe is insulated with 40mm of a molded high temperature diatomaceous earth covering. This covering is in turn insulated with 60mm of asbestos. If the atmospheric temperature is 25 °C, calculate the rate at which heat is lost by the steam per meter length of the pipe.
all of the How much thermal energy is required to heat at water in a swimming pool by 1°C if the dimensions are 4 ft deep by 20 ft wide by 75 ft long? Report your result in megajoules.
An oil storage tank has 20mm steel walls covered with 50mm of fiber glass insulation. if the oil temperature is kept at 150 degree Celsius, what is the rate of heat loss when the outside temperature is 20 degree Celsius and external air coefficient is 20W/m². How much would the heat loss be reduced by doubling the thickness of the insulation?
Find the thermal resistance r (in hr - °F/BTU) and the equivalent R-value (in hr ft?. °F/BTU) of a typical frame 20' x 7.5" wall consisting of a 0.5" plaster board on the inside of the room, nominai 2 x 4 studs, and a 0.5" sheathing on the outside. The spaces between the studs are filled with an R-15 insulating foam. What is the heat loss (in BTU) through this wall in four hours if the inside temperature is 72°F and the outside temperature is 32°F? (Assume that the 15% of the wall's area are studs and the remaining 85% is filled with the insulating foam. Assume that the air is moving outside the wall.) r= 0.0805 x hr: OF/BTU R=0.09 x hr ft2. F/BTU AQ = BTU
A temperature difference of 85°C is impressed across a fiberglass layer of 13 cm thickness. The thermal conductivity of the fiberglass is 0.035 W/m ^ C. Compute the heat transferred through the material per hour per unit area.
3.6 Heat losses through windows in buildings are substantial. What would be the percentage reduction in heat loss that would be mitigated by replacing a window containing a single pane of glass with (a) double-pane low-E insulating glass or (b) a 3-inch-thick sheet of expanded polystyrene sheet? The quoted R values for these items are: • single pane of glass: 0.90 ft 2 hr ° F/Btu, • double pane of low-E insulating glass: 2.3 ft 2 hr ° F/Btu, • 1-inch-thick sheet of polystyrene sheet: 4.0 ft 2 hr ° F/Btu.
What is the rate of heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? thermal conductivity of Celotex in AES = 0.028. Pls determine the temperature gradient and the direction of the heat transfer as well.
Insulating material is used to reduce heat loss from the heating furnace walls to the room. The surface temperature of the insulating material is 100 ° C and the other surfaces 20 ° C. Allowable heat loss up to 140 W / m2 from the wall. If the thermal conductivity of the insulation material is 0.05 W / (m ° C), calculate the required thickness of insulation. insulation thickness = Answer cm