4. An airplane weighing 5500 kg is in a steady level flight with a speed of 225m/s. The pilot initiates a steady pull-up maneuver with a radius of curvature of775 m. The location of center of gravity (CG), center of pressure on wing (CP)and point of action (T) of tail force are marked in the figure. Use g = 9.81 m/s³.Neglect drag on the tail and assume that tail force is vertical. Assuming theengine thrust and drag to be equal, opposite and collinear, the tail forcekN (round off to one decimal place).20 cmCG

Answered: tail force

Engineering

Mechanical Engineering

tail force

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

9. The thin ( 3 mm ) thick plastic panel shown in the figure is lowered from a ship to a construction site on the осean Поог. The plastic panel weighs ( 200 N) in air and is lowered at a rate of ( 2 m/s ). Assuming the ship Cble panel remains vertically oriented, calculate the tension force in the cable. Take ( p = 1000 10 m/s ), and use; kg/m', v 1.31 water Plustic Punel Cplam = 1.328/ Re, Cpturb = 0.072/Re 1/5
A block, as shown below, is sliding on a thin horizontal layer of water (u = 1.68 x 103 kg/m.s) between ice and the block with a speed of 13 m/s. The thickness of the water layer is 3.32 x 10-5 m. Given the following dimensions of the block, what is the force (F) required to maintain this movement? A = 9 cm B = 9 cm C= 8 cm B 2.96 N 5.33 N 4.14 N 4.74 N
= 3570 T AC =144 Example: 1.5 ft It is desired to determine the drag force at a given speed on a prototype sailboat hull. A model is placed in a test channel and three cables are used to align its bow on the channel centerline. For a given speed, the tension is 40 lb in cable AB and 60 lb in cable AE. Flow 4 ft Determine the drag force exerted on the hull and the tension in cable AC. Choc ug the h- as the free hod- DApress the
A highway curve with a radius of 120 m is banked so thatthere is no lateral pressure on the wheels of a car at aspeed of 48 kph. A car weighing 17.8 kN with 1.5-mdistance between its wheels and height h = 0.70 m travelsaround the curve at 96 kph. (a) What is the normal forceon the car’s outer wheels? (b) If friction is great enough toprevent skidding, at what speed would overturningimpend?
A strong wind can blow a golf ball off the tee by pivoting it about point A, as shown in the figure. The golf ball has a radius of 22 mm and a mass of 47 g Assume a golf ball as a smooth sphere. The density of air is (p 1.22 kg/mn') and the viscosity is (u 1.8 10 (kg/m. s)). Calculate the wind speed (V) %3D %3D necessary to do this. V Radius - 22 mm Mass 47 g 6 mm tt
The figure shows two cables AB and AC. Using the tabulated values for the parameters, calculate the magnitude of the projection of FAC onto AB. Also, determine the angle 0 formed by BAC. NOTE: the magnitude of the projection may be positive or negative (or zero). Also, point C lies on the y axis. В L6 FAB A L2 FAC y L3 X 2021 Cathy Zupke parameter value units 3 m L2 L3 L4 3 m 3 m 1 m 3 L6 FAB 2 80 N FAC 100 The magnitude of the projection of FAC on AB is N The angle AB makes with AC is 0-
You are given a drone with an average chord length of 8 in., a wingspan of 2.5 ft, and a weight of 300 g. Based on figure 2, would it stay in the air at a speed of 5 m/s? (Assume ρ=1.225 kg/m3 and Nu=1.516*10-5 m^2/s)
A two-dimensional analysis on the flight of FN FL R an airfoil is shown in the figure. The airfoil shape is traveling at a certain velocity and meets the incoming airflow at an angle of attack a. As shown, the forces affecting FD the flight of the airfoil is the drag force a FA (FD), lift force (F) and the two other Voo variable forces (FN and Fa) acting normal and axial on the airfoil. The lift force (FL) on the airfoil is a function of its length L, velocity V, diameter D, angle of attack a, density p, viscosity µ, and speed of sound c of the air (i.e. FL = f(L, V, D, a, p, µ, c). Use dimensional analysis to show that the lift coefficient C,is a function of a set of dimensionless parameters. Also, is air temperature T, a significant variable in the function of the lift force? Use p,V,D and Ta as repeating variables.
The Air Force's new experimental jet, the X - 9001, is a perfectly flat, rectangular wing. It has a cruising speed of 100 m s¹. Determine the thrust force required to maintain that speed [36 N]. Neglect any frontal area or pressure drag. Drag occurs on both the top and bottom of the plate. The plane may be considered to be 1 m long and 1 m wide.
(b) A Formula 1 team tests their car in a wind tunnel at a scale of 50%, at a speed of Vwinarunnet = 50 m/s. The measured downforce at this speed is Foownforce.WT = 3000 N and the model reference area is Aref wT = 0.5 m?. 1. Find the downforce magnitude on the full-scale race car at the same Reynolds number. Assume constant air density p = 1.2 kg/m. II. It is said that F1 cars could travel upside down, as shown below. At what speed should the full-scale car travel to achieve this, if its mass is m = 740 kg? The acceleration of gravity is g = 9.81 m/s?. Downforce Weight
The case where the rocket has alinear air drag force F= cV , where c is a constant. Assumingno burnout, solve for ω ( t ) and find the terminal angularvelocity—that is, the final motion when the angular accelerationis zero. Apply to the case M 0 = 6 kg, R = 3 m, m =0.05 kg/s, V e = 1100 m/s, and c = 0.075 N ? s/m to find theangular velocity after 12 s of burning.
The drag equation for the Gofaster 172 is: D = 0.0003v2A. D is drag in pounds; v is airspeed in feet/second; and A is aircraft frontal area in square feet. At maximum airspeed, D = 140 lbs. How much does max airspeed INCREASE if the fuselage is narrowed such that frontal area A is reduced from 16 ft2 to 14 ft2? Give the answer in ft/sec AND mph. drag is 140 lbs. at maximum airspeed, regardless of frontal area. the question is: what is the INCREASE in max airspeed, not what is the max airspeed.