Table Q1-2 Weight (g) Mass of residue after drying at 105 ¿C Mass of residue after ignition at 550 óC Mass of residue on Whatman GF/C filter paper after drying at 0.7148 0.3818 0.3571 105 C Mass of residue on Whatman GF/C filter paper after ignition at 550 'C 0.1418 Calculate the concentration (mg/L) of: (i) total solids. (ii) total volatile solids. (iii) total suspended solids. (iv) total dissolved solids.

Table Q1-2 Weight (g) Mass of residue after drying at 105 ¿C Mass of residue after ignition at 550 óC Mass of residue on Whatman GF/C filter paper after drying at 0.7148 0.3818 0.3571 105 C Mass of residue on Whatman GF/C filter paper after ignition at 550 'C 0.1418 Calculate the concentration (mg/L) of: (i) total solids. (ii) total volatile solids. (iii) total suspended solids. (iv) total dissolved solids.

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.32P

See similar textbooks

Similar questions

Il Consider the capability of a process that puts pressurized grease in an aerosol can. The design specification calls for an average of 50 pounds per square inch (psi) of pressure in each can with an upper tolerance limit of 56psi and a lower tolerance limit of 46psi. A sample is taken from production, and it is found that the cans average 51psi with a standard deviation of 2psi. Find the following unknowns. 1. Capability Index (Cpk) 2. Is the process capable at the 30 level? 3. What is the probability of producing a defect? Hind: use the standard normal table as seen below.
A sample of wet aggregate 297.2 N. After drying in an oven, this sample weighed 281.5. The absorption of this aggregates is 2.5%. Calculate the percent of free water in the original wet sample. Weight of the wet aggregates (Wwet) = 297.2 N Weight of the dry aggregates (Wdry) = 281.5 N
ASAP
The following waste water test result were obfecined fox test of teken-The Simple concen foation solids, Suspended susporded a Simple were pecfooned. eusing the 50 mL Calculate oftotel and volctile Solid solids votit volatile Mass of empty dish =62.0039sam mass of 4 Mass %3D dish t doy Solids = 62.0394 %3D dish + igmited solids = 62: 0367 of u Mass of filter=1540 gram of filter tday solids = 1-S5agsom %3D L) MUss y muss of filtest iynited Solids 1:5494 こ

Given that the absorption capacity of a sample of aggregates is 8.7% and the oven-dry mass of the sample is 1000 g. Determine the mass of water that this sample 'can absorb. O A. 43.50 O B. 8.70 O C. 870.00 O D. 0.87 O E. 87.00
Q2: Determine the resultant about the point O of the four forces and one couple which act on the plate shown in the Figure below. Note : for the resutant of 3osihys Forc es, You should computy the magnitude Kdirechion 30N 5 m- 3 ocos4s 25N 2 m 70 N-m 20N 40N o 30
Wet coal is dried in a continuous rotary dryer that operates at atmospheric pressure. The chips with a water content of 40 wt% and must leave with a moisture content of less than 15%. Hot air is fed to the dryer at a rate of 11.6 m (STP)/kg wet coal. HOT AIR MOIST AIR DRYER WET COAL DRIED COAL To monitor the performance of the dryer by sampling the exiting coal and determining their moisture content directly would be a cumbersome procedure and almost impossible to automate. Instead, wet- and dry-bulb thermometers are mounted in both the inlet and outlet air lines, and the moisture content of the exiting chips is determined by a material balance calculator. (STP: Standard Temperature and Pressure is 0*C and 101.325 kPa) (a) The hot air stream has an absolute humidity of 0.058 kg moisture/kg dry air and leaves with 0.087 kg moisture/kg dry air, calculate the mass of water in the exiting air per kilogram of wet coal fed. (b) Can the dryer reduce the wet coal moisture to 15%? If the answer…
The following data is the result in performing the ASTM C128, Determine the Absorption Mass of Pycnometer Mass of pycnometer filled with water 250.00 1,160.00 Mass of SSD sample 900.00 Mass specimen and water Mass of oven-dried sample of pycnometer with 1,724.00 895.00 A None of the above B 0.56% 56% D 5.6%
In standardization, 10.00 mL of Naz C2 04 solution required 39.17 mL of KMN04. Find the molarity of KMNO,. The unknown required 14.44 mL of MnO,. Find Ca in the urine. (Answer: 1.086 x 10 M, 7.840 x 10 M)
Asphalt Technology HW Lecture 5 From the thin film oven test, it was found the following results: Weight before heating (om) Weight after heating (om) Container No. Original Pen No. (from penetration test) 131 dmm 50.3 48.8 2 49.7 48.2 Find the loss in weight due to the effect of heat and air and determine the retained penetration it the penetration vatue of residue after thin fim oven test was 112 dmm. Then compare the results with standards (Specification timits (EN 12607-1): Change of mass, a 0.8% and retained penetration 2 43%. Salutian 1- Find the average weight before and after heating as shown in the following table: wa Avarage weight after haating (gm) Wsi Averaga welght hafore haating (gm) 2. Find the loss in weight of residue after thin film oven test is reported as the percentage by mass of the original sample = 100 =? sample has an overall mass? loss or gain) ? (> orcor) a.8% (the max limit of EN standard). 3- Retained penetration 7 (> orcor=) 43% (the limit of EN…
4. Data taken on solids contents of a walcr sample are given below. All samples were 50-ml aliquots. Residue in evaporating dish after 4 hr at 105 C-36 mg Residue in evaporating dish after 4 hr at 550°C-34 mg Residue on Whatman GFC Alter after drying at 105°C for 1 hr -12 Net ash content (tare subtracted) after firing flter and residue at 550 C-11 mg Determine the concentrations of total solids, total volatile sohds, suspended solids, and volatile suspended solids.
MPN of effluent is 106/100 ml and it reduces to 102/100 ml after chlorination. Find percentage removal (%R) and log removal (logR) of MPN.