Suppose a process is responsible for YZ% of the execution time on a machine. Using a particular hardware will speed up the process by a factor of 20. An alternative solution is responsible for a total of 50% of the execution time. Compare these two design alternatives. Here, Y-First digit of your roll number, and Z-Second digit of your roll number. For example, if roll number is 2012-CS-427, then YZ-42
Q: Suppose the implementation of an instruction set architecture uses three classes of instructions,…
A:
Q: Question: Suppose a program of 600 instructions runs on a 2 GHz processor. The frequency of…
A: When frequency of instruction and clock cycles counts per instruction is given, then average Clocks…
Q: What is the minimum number of cycles needed to completely execute n instructions on a CPU with a k…
A: We need to find a formula to find the minimum number of cycles needed to completely execute n…
Q: Compare zero-, one-, two-, ad three address machines by writing programs to compute (A +BXC) ÷ (D –…
A: Here is the answer with an explanation:-
Q: For microprocessors with adjustable voltage, reduction in voltage may result in reduction in…
A: This question comes from Microprocessor which is a paper of Computer Science. Let's discuss it in…
Q: Consider computing the overall MIPS for a machine A for which the following performance measures…
A: So here question is given we have to calculate CPI and MIPS
Q: Consider a hypothetical machine with the following characteristics: a. instruction format: (total of…
A:
Q: It is possible for compilers and assemblers to be built to order assembly language instructions in a…
A: The hardware cannot support certain combinations of instructions (two instructions in the pipeline…
Q: a computer running a program that requires 250 seconds, where 70 seconds is spent executing FP…
A: Computer running program time :-250 secs Total Time spent :-250 FP instructions in…
Q: Round Robin CPU Scheduling PROCESS AT BT CT TAT WT P1 4 P2 1 5 P3 2 2 P4 3 1 P5 4 P6 6 3 Avg TAT= |…
A: The Answer is
Q: design a small computing system with a customized N (= 4th and 5th digit of your ID# from the LEFT…
A: Lets see the solution in the next steps
Q: R1 = X + 1 Y = R1 + R2 R1 = R2 + X Complete the following: Lay the instructions out as they would…
A: Given Instruction : R1 = X + 1Y = R1 + R2R1 = R2 + X S1: Fetch instruction, S2: Decode opcode,…
Q: An assembly language program is given below, where assume that, SS=2000H and SP=2009H; Flag…
A: SS=2000H andSP=2009H; Flag register, F=FFCDH. MOV AX, 7645HMOV BX, 4477HMOV CX, 8899HMOV DX, BXPUSH…
Q: Assume that we compile a program with two different compilers for the same ISA, then run the two…
A:
Q: onsider a multilevel computer in which levels are vertically stacked, with the lowest level being…
A: Answer :
Q: Consider a hypothetical machine with the following characteristics: a. instruction format ; (total…
A: part 1: As, IR contain both opcode and address First instruction is LDA 20 ; load A from memory…
Q: Compilers and assemblers have the ability to reorder assembler instructions in order to avoid…
A: Introduction: First, certain hardware combinations aren't supported (two instructions in the…
Q: Suppose you have a RISC machine with a 2.7 GHz clock (i.e., the clock ticks 2.7 billion times per…
A: The answer is..
Q: Use the Fetch Decode Execution steps to execute the assembly language into machine instructions and…
A: After examining each statement, what happens during the execution of each statement is explained as…
Q: An interrupt from a CPU causes the processor to halt what it is doing and react to the signal…
A: The answer is...
Q: 1. T/F - if (B)=006000 (PC)=003600 (X)=000090, for the machine instruction 0x032026, the target…
A: Actually, register is a used to stores the data\information.
Q: Consider an equation, W = (X + Y ) * Z is run using CISC one address format and illustration of its…
A: We need to find the result and storage location of result for the given code.
Q: Define pipelining in terms of increasing the speed of a processor, and then determine how many…
A: Analysis of the issue: Data Provided: 5 instructions total. 1 cycles per stage, overall. To locate…
Q: benchmark program is run on a 40 MHz processor. The executed program consists of 80000 instruction…
A: Total time = effective CPI * instruction Count * CPU clock cycle time Effective CPI = Fi*CPIi…
Q: If a complicated program is written using CISC and RISC computer system. Which one of the following…
A: CISC and RISC are two forms of CPU design.
Q: Consider two different machines, M1 and M2. M1 has a clock rate of 500 MHz and M2 has a clock rate…
A: Please refer below explaination: Clock cycle time=1/clock rate Execution/cpu time = Cycles count *…
Q: Consider a machine where total addressable physical memory size is 32 Kbytes. If we would like to…
A: given, physical mem size=32 p=8KB R=2KB
Q: Consider a Computer which has a memory which is capable of storing 4096 K words and each word in…
A: Given Data : Nmber of memory words = 4096K words Word size = 32 bits Addressing modes = 6 Number of…
Q: Use the Fetch Decode Execution steps to execute the assembly language into machine instructionsand…
A: Actually, there are 3 steps to execute one instruction 1) Fetch the instruction 2) Decode the…
Q: A 32-bit microprocessor with the same bus cycle as a 16-bit microprocessor is an example of this. If…
A: This kind of computer processor has all of its logic and control on one integrated circuit, or a…
Q: Suppose a program takes 2 billion instructions to execute on a processor running at 2.5 GHz. Suppose…
A: DATA GIVEN:- Instruction that needs to be executed = 2*109 instructions Processor speed = 2.5 GHz…
Q: Question 1 You want to run two programs A and B on a computer. On the computer, four types of…
A: The current scenario here is to calculate the CPU time . Data given: Cycle period=120ps. No of…
Q: Consider computing the overall CPI for a machine Z for which the following performance measures were…
A: Computer Per Instruction: CPI or Computer Per Instruction gives the average number of the cycles of…
Q: ISA of a hypothetical CPU 1 Address Memory: Address Data – (8-bits) LOAD M 100 25 STORE M 101 90 ADD…
A: Note: According to guidelines we are supposed to answer only first 3-sub part at a time. please…
Q: Given an instruction sequence with instructions in classes A, B, and C as the table below:…
A: Give an instruction sequence with instructions in classes A, B, and C as the table below.…
Q: Consider three different processors P1, P2, and P3 executing the same instruction set with the clock…
A:
Q: In the figure below, what should be in the blue boxes for IR and MAR, respectively? Start Example 1…
A: For the above give o[tions choose the right option which goes in the blue boxes for the above…
Q: Suppose we had a processor design with 5 stages where each stage takes the following amount of time:…
A: Suppose we had a processor design with 5 stages where each stage takes the following amount of time:…
Q: 1. T/F-if (B)=D006000 (PC)=003600 (X)=000090, for the machine instruction Ox032026, the target…
A: As per bartlby guidelines, only 3 sub questions can be answered.
Q: Consider two different implementations, M1 and M2, of the same instruction set. There are three…
A: The given data is following- Clock rate for M1 is 2.0 GHz which is equal to 2 × 10^9 Hz. 0 GHz = 2…
Q: 2- Consider two machines with two different instruction sets. Machine A has a 2 GHz clock and…
A:
Q: If in a computer system , a cpu is capable to process 100 instructions cycles in 1 second . what…
A: The number of cycles per second or rate at which the current switches direction per second is called…
Q: Given the following sequence of instructions: R1 = X + 1 Y = R1 + R2 R1 = R2 + X Complete the…
A: STEP 1:- Given:- R1=X+1 Y=R1+R2 R1=R2+X
Q: Consider three different processors P1, P2, and P3 executing the same instruction set. P1 has a 3GHz…
A: Given terms are clock rate and CPI of processors P1, P2 and P3 Processor P1 , clock rate = 3GHz ,…
Q: an assembly language program that reads a specified number of positive integer inputs from standard…
A: It is defined as a low-level programming language for a computer or other programmable device…
Q: For a microprocessor, if the total time of all positive cycles in 5 seconds is 2 seconds, and the…
A: Off time for every cycle = Toff = 0.335 microsecond Total time of all positive cycles = Ton = 2…
Q: Trace the execution of the following "Super Simple CPU" program and for a) each step record the…
A: Question a. Solution Accumulator Mem[10] Mem[11] Mem[12] 15 2 5 43 5 2 5 43 3 2 3 43 1 2…
Q: Explain what happens as the following sequences of instructions are executed : MOV DL,05H MOV…
A: MOV AX, 0H MOV DS, AX MOV ES, AX MOV AL, 05 MOV DI, 0A000H MOV CX, 0FH CLD AGAIN: STOSB LOOP…
Q: Use the Fetch Decode Execution steps to execute the assembly language into machine instructions and…
A: Introduction to assembly language program It is defined as a low-level programming language for a…
Q: Given: PROCESS AT BT P1 110 14 P2 141 15 P3 100 35 P4 117 19 P5 131 20 P6 100 25 P7 112 21 P8 110 17…
A: here we have given he solution for finding the waiting time of each process. you can find solution…
Step by step
Solved in 2 steps
- The register we discussed in class has two inputs, D and clock, and one output, Q. If you are interested, you can access a simulator of this circuit at http://www.falstad.com/circuit/e-edgedff.html (note that that simulator has an extra output, !Q, below Q). If D is 1 as clock transitions from 0 to 1, which of the following is true? A. Q is (or soon becomes) 0 B. Q is (or soon becomes) 1 C. Q oscillates between 0 and 1 D. Q holds a steady value, which could be 0 or 1Write a program that calculate the values of (X + Y) x (X – Y) where X, Y = 0, 1, 2, …, 9and prints the following table:X|Y 0 1 2 3 4 5 6 7 8 90| 0 -1 -4 -9 -16 -25 -36 -49 -64 -811| 1 0 -3 -8 -15 -24 -35 -48 -63 -802| 4 3 0 -5 -12 -21 -32 -45 -60 -773| 9 8 5 0 -7 -16 -27 -40 -55 -724| 16 15 12 7 0 -9 -20 -33 -48 -655| 25 24 21 16 9 0 -11 -24 -39 -566| 36 35 32 27 20 11 0 -13 -28 -457| 49 48 45 40 33 24 13 0 -15 -328| 64 63 60 55 48 39 28 15 0 -179| 81 80 77 72 65 56 45 32 17 0Write a python program that calculate the values of (X + Y) x (X – Y) where X, Y = 0, 1, 2, …, 9and prints the following table:X|Y 0 1 2 3 4 5 6 7 8 90| 0 -1 -4 -9 -16 -25 -36 -49 -64 -811| 1 0 -3 -8 -15 -24 -35 -48 -63 -802| 4 3 0 -5 -12 -21 -32 -45 -60 -773| 9 8 5 0 -7 -16 -27 -40 -55 -724| 16 15 12 7 0 -9 -20 -33 -48 -655| 25 24 21 16 9 0 -11 -24 -39 -566| 36 35 32 27 20 11 0 -13 -28 -457| 49 48 45 40 33 24 13 0 -15 -328| 64 63 60 55 48 39 28 15 0 -179| 81 80 77 72 65 56 45 32 17 0
- Christy is interning at HackerRank. One day she has to distribute some chocolates to her colleagues. She is biased towards her friends and plans to give them more than the others. One of the program managers hears of this and tells her to make sure everyone gets the same number. To make things difficult, she must equalize the number of chocolates in a series of operations. For each operation, she can give pieces to all but one colleague. Everyone who gets a piece in a round receives the same number of pieces. Given a starting distribution, calculate the minimum number of operations needed so that every colleague has the same number of pieces. Example represents the starting numbers of pieces for each colleague. She can give pieces to the first two and the distribution is then . On the next round, she gives the same two pieces each, and everyone has the same number: . Return the number of rounds, . Function Description Complete the equal function in the editor below. equal has the…Coding Language is Python, keep it as simple as possible thanks. N one dimensional kingdoms are represented as intervals of the form [a, , b] on the real line. A kingdom of the form [L, R] can be destroyed completely by placing a bomb at a point x on the real line if L SXSR. Your task is to determine the minimum number of bombs required to destroy all the one dimensional kingdoms. Example Input: 1 3 13 25 69 Output: 2A fish-finder is a device used by anglers to find fish in a lake. If the fish-finder finds a fish, it will sound an alarm. It uses depth readings to determine whether to sound an alarm. For our purposes, the fish-finder will decide that a fish is swimming past if:there are four consecutive depth readings which form a strictly increasing sequence (such as 3 4 7 9) (which we will call "Fish Rising"), orthere are four consecutive depth readings which form a strictly decreasing sequence (such as 9 6 5 2) (which we will call "Fish Diving"), orthere are four consecutive depth readings which are identical (which we will call "Constant Depth").All other readings will be considered random noise or debris, which we will call "No Fish."Create a Python program called "fishfinder_firstname_lastname" that takes 1 input of string of 4 numbers separated with comma. Your program must display "Fish Rising", "Fish Diving.", "Fish At Constant Depth" or "No Fish".Example:30,10,20,20 Must display No…
- Consider the following codes. Evaluate and show the running time performance of each line in each code. At the end, indicate the total running time 1. x = 0; for (i = 0; i< n; i++) { for (k = 0; k< n; k++ ) x ++; } 2. x = 0;for (i = 0; i< n; i++){ for (k = 0; k< i; k++ ) x ++;} Your answers should be presented like this: Line 1 = ___ Line 2 = ___ Line 3 = ___ Total Performance = ___Given an integer N and a base X, the task is to find the minimum number of operations required to represent N as a sum of the distinct powers of X. In each operation, you can either increment or decrement N. You are allowed to make the given operation any number of times Examples: Input: N = 7, X = 3 Output: 3.Write an assembly program, that sets four 7- segment's value equal to 0 for the first time and simulates a timer with minute and hour handles. Ask the user to press S/s to start the timer. Also, the user can stop the timer by pressing E/e. Seven segments values is going to be shown on the middle of the PC's display. In addition, the program has to be terminated by pressing 'Q' to quit. Your program must show a menu to the user about S/ s, E/e, and Q keys. Hint: The two seven segment on the right are working like the secound handle of a clock. This means they can count from 00 to 59 and each time they reach the upper boundary (59), one unit must be added to the left seven segments.
- Write an Arduino program that simulates a robot car using: • Two gear motors (DC motors) • One motor driver • A servo motor The car should move forward, stop for a one second, and then move backward (this process should be repeated continuously). When the car is moving forward the servo motor should rotate from angle 0 to angle 180 and back from angle 180 to angle 0. When the car stops or is moving backward the servo motor should stop rotating. Hello i need the solution using arduino c language as soon as possibleAbstract: the main purpose of this experiment is build real time system using PPI 8255 to control devices connected to. Problem description: assume that there are two devices are connected to port A and two sensors are connected to port B of PPI 8255. They work according to the following table Sensors (S1S2) Devices (DID2) 00 01 01 10 10 11 11 00 Write a program to control these two devices according to the values of sensors.Write the robot program using the VAL+ for the following automation case. First draw the problem; then handwrite the VAL+ code. The robot picks up FIVE blocks of size 100x100x100 mm that are stacked at a fixed position and place them at the corners and center of a square table of size 500 x 500 mm. Select the original position on the table on your own.