Stress and strain 3. A brass rod with a length of 1.40 m and a cross- sectional area of 2.00 square cm is fastened end to end to a nickel rod with length L and cross- sectional area 1.00 square cm. The compound rod is subjected to equal and opposite pulls of magnitude at its ends. 4.00 x104 N (a) Find the length L of the nickel rod if the elongations of the two rods are equal. (b) What is the stress in each rod? (c) What is the strain in each rod?

Stress and strain 3. A brass rod with a length of 1.40 m and a cross- sectional area of 2.00 square cm is fastened end to end to a nickel rod with length L and cross- sectional area 1.00 square cm. The compound rod is subjected to equal and opposite pulls of magnitude at its ends. 4.00 x104 N (a) Find the length L of the nickel rod if the elongations of the two rods are equal. (b) What is the stress in each rod? (c) What is the strain in each rod?

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 57PQ: A copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length...

See similar textbooks

Similar questions

A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a second 100-N weight is added to the wire, it stretches 3.0 mm. The diameter and the length of the wire are 1.0 mm and2.0 m, respectively. What is Young’s modulus of the metal used to manufacture the wire?
Normal forces of magnitude 1.0106N are applied uniformly to a spherical surface enclosing a volume of a liquid. This causes the radius of the surface to decrease from 50.000 cm to 49.995 cm. What is the bulk modulus of the liquid?
Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
Can Young’s modulus have a negative value? What about the bulk modulus?
A copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length L and cross-sectional area 1.0 cm2. The compound structure is pulled on each side by two forces of equal magnitude 6.00 104 N (Fig. P14.57). Find the length L of the steel rod if the elongations (L) of the two rods are equal. Use the values Ysteel = 2.0 1011 Pa and YCu = 1.1 1011 Pa. FIGURE P14.57
Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?
A copper wire is 1.0 m long and it diameter is 1.0 mm. if the wire hangs vertically how much weight must be added to its free end in order to stretch it 3.0mm?
Referring to Fig. compute the maximum force P that can be applied by the machine operator, If the shearing stress in the pin at B and the axial stress in the control rod at C are limited to 4000 psi and 5000 psi, respectively. The diameters are 0.25 inch for the pin, and 0.5 inch for the control rod. Assume single shear for the pin at B. Figure P-121 2 in 10 MATHno.com 6 in 2 in
PROBLEM 2. The light rigid bar ABCD shown in Fig. P-252 is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P = 41. 29 KN is applied. Hint: convert the distance of each member into mm, area of steel and aluminum into mm^2, & E into MPa.. Steel L-3 ft A- 0.5 in E- 29 x 10° psi 4 ft Aluminum L-4ft A- 0.75 in E - 10 x 10 psi + 2 ft Figure P-252
A fishing rope of length (74+ 50) m has the diameter (74 + 5) mm. When a weight of (74 +200) N is hung on the rope, the extension is (74 + 50) mm. Calculate,i. cross-sectional area of the fishing ropeii. strain
Stress and strain 3. A brass rod with a length of 1.40 m and a cross- sectional area of 2.00 square cm is fastened end to end to a nickel rod with length L and cross- sectional area 1.00 square cm. The compound rod is subjected to equal and opposite pulls of magnitude at its ends. 4.00 x104 N (a) Find the length L of the nickel rod if the elongations of the two rods are equal. (b) What is the stress in each rod? (c) What is the strain in each rod?
Two solid cylindrical rods (1) and (2) are joined together at flange Band loaded, as shown. The diameter of rod (1) is d; - 1.53 in. and the diameter of rod (2) is de- 3.19 in. Determine the normal stresses in rods (1) and (2). Assume P- 15 kips and Q- 28 kips. Use positive for tensile stress and negative for compressive stress. 2) Answers: ksi. ksi.