Specify an acceptable amount of outdoor air for ventilation of the following: a) 12 ft by 12 ft private office with 8 ft high walls - ANS: 13.6 cfm b) department store with 20,000 ft^2 of floor area - ANS: 4,650 cfm

Specify an acceptable amount of outdoor air for ventilation of the following: a) 12 ft by 12 ft private office with 8 ft high walls - ANS: 13.6 cfm b) department store with 20,000 ft^2 of floor area - ANS: 4,650 cfm

Construction Materials, Methods and Techniques (MindTap Course List)

4th Edition

ISBN:9781305086272

Author:William P. Spence, Eva Kultermann

Publisher:William P. Spence, Eva Kultermann

Chapter40: Heating, Air-conditioning, Ventilation, And refrigeration

Section: Chapter Questions

Problem 12RQ

See similar textbooks

Related questions

Q: Calculate the energy required to lift an elevator and its occupants with amass of 2000 kg for the…

A: Given data: mass of elevator = 2000 kg height of each story = 4.5 m

Q: An existing roadway (P₁P2 is the centreline) crosses course EF of a closed traverse (Figure Q5). The…

Q: From the given cross section of the proposed municipal road, it is required to determine the volume…

Q: Use 4 decimal places at all instances and box the final answers. Please write legibly Determine the…

A: Using equilibrium equation

Q: = 10 m/s a 16 m/s² 300 mm 300 mm At the instant that 0= 70° rod AB is subject to a deceleration of…

Q: For the beam loaded as shown in the figure compute the magnitude, direction and position of the…

Q: In a three-layered soil system, the thicknesses of the top and bottom layers each are half the…

A: Given data: In a three layered soil system, Thickness of top and bottom layers each are half the…

Q: 5.16. Determine the flow rate in the tube shown in Figure P5.16 if the manometer fluid is mercury…

A: Given ;

Q: 18. A manometer is attached to a tank containing three different fluids as shown. What will be the…

Q: Q- The surface area of a plate is 0.4 m² and its weight is 500 N which slides down on an inclined…

A: Given- Surface area A=0.4 m2Weight of plate W=500 NSpeed of sliding plate V= 4 m/sDynamic viscosity…

Q: Problem #1 A nearly horizontal channel has a bottom width of 3 ft, and it carries a discharge of 60…

A: Given : Bottom width - 3ft Q - 60 cfs at depth of 4ft

Q: (a) Determine by trigonometry the magnitude of the force P so that the resultant force exerted on…

A: From the figure it can be observed that there can be many values of P, actually the value of P…

Q: Situation 12: A masonry dam of triangular cross-section, with one end face vertical, has a base of 3…

A: Solution: Given: base = 3 m height = 6.75 m Vertical reaction is at 1/3

Q: F2-28. Determine the component of projection of the force along the line OA. F = 650 N 8 13. 12 5 A…

A: Given :

Q: A circular primary clarifier processes 5005 cubic meters of municipal wastewater every day. The…

A: Given data: Average flow rate = 5005 m3/d The overflow rate = 35m3/m2d

Q: Situation: For the given beam E = 29,000 ksi and I = 300 in4 shown in figure 6. Determine the…

Q: The rigid pipe is supported by a pin at A and an A-36 steel guy wire BD. 4 ft B A 3 ft D 3 ft C If…

Q: 4. For the data below, determine the cumulative volume in cubic yards between station 0+00.0 and…

Q: Grades of gl=-2.50% and g2=+1.50%, the intersection at elevation 2560.00 ft. Fixed elevation 2567.00…

A: BVCsta=PVI-L2=31500-L2BVCelv=PVI-g1L2=2560--0.025L2=2560+0.0125L

Q: Know that all = 25.5 ksi and Tall = 14.5 ksi. 20 kips B 10 ft 2 kips/ft -30 ft с 20 kips 10 ft D

Q: Two simply supported beam A and B are under same udl Loading. The span of A is double of span B. The…

Q: The magnitude of the force F is 120 lb. Find its vector representation. 18 ft 15 ft B

A: Given ; Magnitude of the force is 120lb To Find - The vector Representation?

Q: PROBLEM 1: The beam shown below has a fixed support at A and a roller at B. El is constant. Use the…

Q: Water flows through a new cast iron pipe at a velocity of 1.8 m/s. The pipe is 480 m long and has a…

Q: Prob. 5.2-12. For the beam in Fig. P5.2-12. determine the following: (a) V₁ and M₁, the reactions at…

Q: A highway embankment with a volume of 800,000 cy is being constructed by compacting dry gravel…

Q: Problem 1 Use the second-order integration method to find the deflection equation. Let EI =…

A: Given data EI = constant Find deflection equation using second order integration method.

Q: 1. What is the relative stiffness of span AB, KAB? 0.375 I 0.125 I 2.667 I 0.250 I…

A: From the given question it is required to determine the distribution factor and relative stiffness…

Q: Determine the moments at A, B, C, and D and draw the moment diagram of the frame shown in the…

Q: b) Whole circle bearing of line connecting TP1 and IP is 300 and whole circle bearing of line…

A: We have to calculate chainage of TP1 and whole circle bearing of line connecting TP1 and IP is 30°…

Q: Q5. Grades of gl=-2.50% and g2=+1.50%, the intersection of grade lines at station 315-00 is at…

A: Calculation of vertical Curve and finding of Curve length and stations and elevations of BVC and EVC

Q: Problem 4. A. Draw the F.B.D. of the frame shown in Fig. (4-A). B.Draw the F.B.D. of the figure…

Q: DETERMINE THE REACTIONS AND SHEAR & MOMENT DIAGRAM in MEMBER BCDE ONLY Let P=22 B A 4'- - C…

A: It can be observed in the given diagram that the support B which has a roller support will not have…

Q: 2. Calculate the cut area of the drawing below both with the known shapes formula and with the…

A: This question is from survey engineering. Here we are given with a cross section of structure . This…

Q: Q3 A reinforced concrete footing carries two 400mm x 400mm columns centered 2m apart and…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A reinforced concrete rectangular beam has a width of 320 mm and a total depth of 650 mm. The beam…

A: Solution: Given: Maximum Dead load moment = 350 kN-m h = 650 mm b =350 m d = 650-(30+282)=606 mm d'…

Q: The location of the plastic neutral axis from the top edge of the flange in mm (ANS 11). b. The…

Q: A steel pipe of length L=3.5m, outside diameter d₂ = 0.8m and inside diameter d: 0.6m. The inside of…

Q: Advantage of Measured or Unit rate Contract اختر أحد الخيارات a. the tender sum tells him the exact…

A: This question is from costing and estimation subject Here we are asked to find a advantage of unit…

Q: PROBLEM 2: The frame shown below has a fixed support at A and a pin support at C. El is constant.…

A: Given values: Consider the given frame with constant EI.

Q: F2-28. Determine the component of projection of the force along the line OA. F = 650 N 13. 12 5 A -x…

A: Given, F= 650 N To determine, Component of projection of force F along OA

Q: Use the substitute member to make a complete analysis of the complex truss shown. 15 kN- b a C 2 at…

A: Truss : Truss is a pin joint structure subjected to loading only on joint and there is only one…

Q: 12. A backfill of a retaining wall consists of y=19 kN/m³ which is 6 m high. Find the total earth…

A: Given data: A backfill of a retaining wall consist, Y = 19 kN/m3 Height, H = 6 m Coefficient of…

Q: Could you explain the calcutions in more detail like why you used does numbers in does ways

Q: Determine the weight of an exploration vehicle whose mass is 250kg on the Earth. What is the mass of…

A: Given:- The mass of the vehicle on the earth = 250 kg The value of g on the moon = gmoon = 1.6 m/s2…

Q: Suppose that F1 = 200 N Determine the magnitude of the resultant force as well as the direction of…

A: Given : F1 = 200N To Find : Magnitude of resultant force and the direction ?

Q: Determine the internal normal force, shear force, and bending moment in the beam at points B and C.…

Q: Given a liquid water having a volume of 6m3 and weight of 44kN at 4°C, Calculate a. Specific weight…

A: Note:-Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: For laminar flow in a pipe, the drop in pressure Ap is a function of the pipe length L, its diameter…

A: Lets design the laminar flow in pipe , with drop in pressure per unit length. So, Drop in pressure…

Q: Describe in detail the difference between a static mode imaging and a dynamic mode imaging. What is…

A: Difference Between static mode imaging and dynamic mode imaging: In static imaging a color contrast…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Acceptable amount of outdoor air

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need a literature review about the Enhancing indoor air quality and safe entertainment in sports halls}......... (introduction about 6 lines) (determination abou 5-6 line) (and 10 reference with link of the reference) pls quick..
b.) calculate the outside air flow for the restaurant dining area where cold air is supplied from the ceiling, lit/sec
I need a literature review about the Enhancing indoor air quality and safe entertainment in sports halls}......... - (introduction about 6 lines) - - (determination abou 5-6 line) - (and 10 reference with link of the reference) - finally i need the conclusion 5 or 6 line urgent.
Explain the following questions a and b. a) where is the first hose line stretched for a cellar fire in an older apartment building. b) list three benefits of horizontal ventilation and vertical ventilation related to multiple dwelling buildings.
Which statement is TRUE about displacement ventilation in UFAD systems? air from the floor is prone to carrying dust vertical airflow may have health benefits mixing is enhanced resulting in even air temperatures supply air temperatures are lower than for overhead systems
me: 5. -NA NOTE 1: The wall height for all rooms is 11 feet. NOTE 2: When calculating heat gain and loss for the provided drawing, Round U factor to 3 decimals places, Round heating transfer multiplier (HTM) to two decimal places. NOTE 3: For each window, door or surface area, round off aquare feet to the ac whole number. N What is the perimeter in feet of exposed wall for the entire house provided? 2'8 X 4'0 2'8 X 4'0 Answer Room 3: 10' X8' 5'0 X 6'0 Room 4 22' X16' Room 2 18' X14' 5'0 X 6'0 7 2'8 X 6'8" 3'Q X 6'8" & b W 30 3 2'0 X 3'0 ID: B Room 5 26' X20' Room 1 30' X18' Room 6 8' X8' 5'0 X 6'0 2'8 X 4'0 5'0 X 6'0
For a given HVAC water piping system, a pressure of 67 ft of head is required to produce 44 GPM water flow. How much pressure in ft will be required to flow 64 GPM?
If the room in problem 16 faced the sun, an additional cooling load would becreated. This extra cooling load would be due to the sun shining through thewindow and heating the room. A window facing south would allow a maximumof 75 Btu per hour to enter the room for each square foot of window area. Ifthe room has its window facing south, what is the maximum cooling load forthe room?
It is generally desirable to provide mechanical ventilation in all rooms of a building which are occupied by more than O a. 14 people O b.32 people Oc 50 people O d. 28 people The most expensive filters used in air conditioning system are O a. Electric precipitators O b. Spray washers O c Dry filters O d. Viscous filters
Provide a reasonable design for a 99.4% efficient ESP treating 30,000 m3/min of gas. The dust has a resistivity of 7.1x1010 ohm-cm. Specify the total plate area, channel width, number and size of plates, number of electrical sections (total and in the direction of flow), and total corona power to be supplied, and estimate the overall dimensions.
IX. PROBLEM SET NO.1 1. A closed tank contains 0.610m of mercury (sp.gr.=13.6), 1.524m of water,2.438m of oil (sp.gr.=0.75) and an air space of 1.0m above the oil. If the pressure at the bottom of the tank is 276kPa, what should be the reading of the gage in the top of the tank ?
Civil Engineering There is a 5 story building each floor consisting of 4 spaces. 2 of these spaces are residential and 2 are public. You will have a drainage of 450 gal/day and your vent stack will have a developed length of 32 feet. Each space has 1 bathroom and 3 bedrooms. Each space has the following fixtures:The private spaces have a bathtub, clothes washer, water closet (flush valve), lavatory and kitchen sink.The public spaces have a drinking fountain, service sink, showerhead, urinal (flush tank and siphon jet) and water closet (flush tank).Part 6: What is the Minimum Septic tank size in gallons?Part 7: What is the required drainage area for an absorption bed with a percolation rate of 7 min/inPart 8: If instead you wanted to use a seepage pit of diameter 5 ft with a 4 ft depth, determine the required drainage area and number of seepage pits needed?