Solve the given beam using area moment method. Assume El = 3500 kN-m?. Solve the given beam using area moment method. Assume El = 3500 kN-m2.W2A4 m2 m2 mSETw1 (kN/m) W2 (kN/m)F (kN)A(1,2,3,4,5)1020B(6,7,8,9,0)121973. Calculate the rotation at B, in rad.B.

Answered: Image /qna-images/answer/605c953c-c728-4a30-93c6-3132800124fa.jpg

Solve the given beam using area moment method. Assume El = 3500 kN-m². W₂ A SET A(1,2,3,4,5) B(6,7,8,9,0) 3. 4 m W₁ Calculate the rotation at B, in rad. B W1 (kN/m) W2 (kN/m) F (KN) 10 20 8 12 19 7 2 m C 2 m F D

Solve the given beam using area moment method. Assume El = 3500 kN-m². W₂ A SET A(1,2,3,4,5) B(6,7,8,9,0) 3. 4 m W₁ Calculate the rotation at B, in rad. B W1 (kN/m) W2 (kN/m) F (KN) 10 20 8 12 19 7 2 m C 2 m F D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Two observation wells penetrated into a confined acquifer and located 1.5 km apart in the direction…

A: Two observation wells- Distance s=1.5 km=1.5×1000 m=1500 mHead=45 m & 20 m.k=30 m/day,porosity…

Q: A rectangular beam 150 mm wide and 200 mm deep, is simply supported on a span of 6 m. Two loads of 5…

Q: 2- A fully saturated normally consolidated clay sample was tested in an unconfined compression test.…

A: compression stress = 120 kNm2 pore water pressure at failure= - 70kNm2 To find- a) effective…

Q: In this Question the cable attached to a tower as you can see a) Since f1 = 8m and f2 = 8m, find the…

Q: 04: Find (D.O) and the (Deficit) Stream Q (m/s) T (°C) A 3.7 21 C 19 6.2 for the stream (B), If:…

A: QA = 3.7 m3/s Qc = 6.2 m3/s DA = 4.49 mg/L DB = 3.58 mg/L

Q: A channel of rectangular cross section conveys water at a rate of 9 m3/sec. with a velocity of 1.2…

Q: A granular soil sample taken from the field has a density of 1900 kg/m3. In a laboratory test, it…

A: Given data in question Field Density = 1900 lg/m3 Solids Density =2600 kg/m3 Moisture content…

Q: When conducting CBR test, it is observed that the load dial reading at 2.5 mm penetration is 33…

Q: A cylindrical buoy 100mm in diameter and 120mm high is placed vertically inside the tank. The tank…

A: Weight of buoy=5 N Diameter of Buoy= 100 mm Height of buoy=120 mm Tank diameter =150mm water…

Q: How do I get the support forces?

A: For the given truss, A 500lbs load is applied at A. The truss is supported at D and C, also BC…

Q: A superspeedway in New Delhi has among the highest super-elevation rates of any track on the Indians…

Q: 10. A rod is being designed for a speed of 110 km /hr on a horizontal curve with a super elevation…

A: Speed, V = 110 km/hr. Elevation = 8% Co-efficient of side friction = 0.10 What is the minimum…

Q: Q3 0.5m 5 kg 0.5m 7 kg 0.5m 4 kg E=207 GPa I=12 10* m* 0.5m Predict the fundamental natural…

A: Given; m1 = 5 kg m2 = 7 kg m3 = 4 kg E = 207 Gpa I = 12×10-6 mm4

Q: The co-efficient of friction in the longitudinal direction of a highway is estimated as 0.396. The…

A: Coefficient of friction f=0.396 Speed V=65 km/hr It is needed to find the breaking distance (S).

Q: The beam is made from southern pine and is supported by base plates resting on brick work. (Figure…

A: Given: Required : Length of base plate at A and B

Q: A concret wall with a thickness= The wall carries linear service lods PD and P₁: PD = 9 kips/ft PL =…

A: qa = 4000 psf γ = 100 pcf γc = 150 pcf

Q: Match all the possible combinations between Column X (Cement compounds) and Column Y (Cement…

A: Cement compounds in column X with there different cement properties in column Y.

Q: *2-60. The tide gate opens automatically when the tide water at B subsides, allowing the marsh at A…

A: Determine the horizontal reaction at the smooth stop C

Q: Situation 2: 17.9m 15m 9.5m 20k/m. Solve for the maximum deffection if El=390 000 kN/m²

A: The beam is given as EI=390000 kN/m2 To find:- Maximum deflection Concept:- The double integration…

Q: Determine the spacing between stirrups at maximum shear force for the simply supported beam that has…

A: Since the beam is symmetrically loaded we get equal reaction at supports RL = RR = Wu*L2 Wu =…

Q: A timber beam is 100 mm wide and 150 mm deep. The beam is simply supported and carries a central…

A: Given- A timber beam- width=100 mm, depth=150 mm, Simply supported beam- central concentrated load=W…

Q: Determine the theoretical buckling strength (Euler buckling load) for a W8x35 A992 column with an…

A: Given: Section W 8 x 35 A992 steel; fy = 50 ksi fu = 65 ksi Length, L = 20 ft To determine the…

Q: 7.) A non-uniform bar weighs 400N and is 4-m long. When it is supported by a fulcrum at its…

Q: An extended layer of soil with homogeneous rounded grains has 10% of the material finer than 0.007…

A: An extended layer of soil- 10% of the material finer than 0.007 mm. Constant C=750, To Find- The…

Q: A 100 m tape weighing 30 N is suspended between the two ends under a standard pull of 180 N. The…

A: Given: A 100 m tape weighing 30 N. The tape is suspended between the two ends under a standard pull…

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

Q: There are 3 strategies to solve the turbulent flows in conduits, which are as follows: Case 1 Case 2…

A: Equations for turbulent flow in a conduit is given. It is needed to determine which of the given…

Q: Design the economical section of a rectangular flume that will carry a discharge of 119 cu. ft. per…

A: Design the economical section of a rectangular flume.

Q: Derive and show the relationship or transformation of e Kv> to V/v = Ite e Vs =

A: Void ratio e=VvVs Where Vv=Volume of void Vs=Volume of soil solid

Q: 500 mm B 500 mm- 2000 mm 1000 kN 200 mm- Section AB 200 mm

Q: The magnetic bearing of a line AB was N 59° 30' W in the year 1967, when the declination was 4° 10'…

A: Magnetic bearing = N 59030' W Declination = 4010' E Present declination = 30 W What is the whole…

Q: This is the stiffness matrix for a horizontal roller, if the roller was vertical instead of…

A: Yes, if the roller was vertical instead of horizontal, the rows 1 and 2 of the stiffness matrix…

Q: Direction: One hour triangular unit hydrograph of a watershed has the peak discharge of 60 m³/sec.cm…

A: Peak discharge = 60 m3/sec.cm Duration = 10 hrs. Time base 30 hrs. f index = 0.4 cm per hrs. Base…

Q: The perception-reaction time for a vehicle travelling at 90 km/h, given the coefficient of…

A: Speed V=90 km/hr, Coefficient of longitudinal friction f = 0.35, Stopping sight distance, SSD = 170…

Q: The drained shear strength parameters of a N.C.C are (C' = 0 and Ø' = 30°). The found to unconfined…

Q: Question (1): For the beam shown in figure (1): 1- Calculate all support reactions. 2- Calculate the…

A: Determine a. Support reaction of the beam. b. Internal force and moment at C and D.

Q: Instructions: Answer the following problems. Always show your solutions. Print this as your first…

A: The magnitude of the force at point B (F) = 20 N The stiffness in the spring at C = 60 N/m When θ =…

Q: Find the amount of land required in a sanitary landfill to f city of 120 000 in population, knowing…

A: population of city=120000 persons amount if waste generation=2.2 kg/capita/day density of solid…

Q: A 90 mm diameter shaft rotates at 1200 rpm in a mm long journal bearing of 90.5 mm internal…

A: Diameter of shaft = 90 mm diameter if bearing = 90.5 mm N= 1200 rpm Dynamic velocity = 0.12 Pa.s To…

Q: How may advances in computing power and data analytics improve transportation policy, practise, and…

A: Advances in computing power and data analytics have the potential to revolutionize transportation…

Q: ● It is stated that the clay layer shown in the figure is OVER CONSOLIDATED clay. The…

Q: The base length of the runway at the mean sea level (MSL) is 1500 m. If the runway is located at an…

A: The base length of the runway at the mean sea level (MSL) is 1500 m. The runway is located at an…

Q: T 3) The weight of the unit length of the homogeneous cable in the figure is given as w. and since…

Q: When conducting CBR test, it is observed that the load dial reading at 2.5 mm penetration is 33…

Q: A tied column which is subjected to an eccentric load has dimensions of 300 mm x 500 mm which is…

A: Answer (a) Calculation of value of the Nominal load 'Pn' Let us first draw the free body diagram…

Q: By (a) method of least work, and (b) superposition method [E10 =ML/(n+1), EIA-ML2/(n+2)] determine…

A: Given: Required : Reaction at support and moment at B, C and D Note : As per bartleby guidelines, I…

Q: 4. Length of offset from long chord is equal to a)R-V R²-X² b) √ R--X²-(R-M) c)) √ R²-X² -(R+M) d) v…

Q: *7-8. Determine the internal normal force, shear force, and moment at point C. -1.5 m C 3 m 0.2 m 1m…

Q: The error in measuring the radius of a 5cm circular rod was 0.2%. If the cross-sectional area of the…

A: Given that :- radius = r = 5 cm error in measuring the radius = 0.2% To calculate the resulting…

Q: A 90 mm diameter shaft rotates at 1200 rpm in a 100 mm long journal bearing of 90.5 mm internal…

Concept explainers

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.

Question

Solve the given beam using area moment method. Assume El = 3500 kN-m?.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data

VIEW

Step 2: Reaction Calculations

VIEW

Step 3: Elastic Curve

VIEW

Step 4: Moment by parts

VIEW

Step 5: Slope calculations

VIEW

Solution

VIEW

Step by step

Solved in 6 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. Determine the location of the center of gravity of a wire with uniform cross- sectional area and specific weight., shown in the figure below. The wire is in the form of a broken line P, P2 P3 P4, with P:(-3, 7), P2(-1, 1), P3 (3, 5) and P. (5, 3). C.G. (0.30, 3.60) Pi-3, 7) P(3, 5) M(-2, 4) 8 M5(1, 3) XM(4, 4) PA(5, 3) P2(-1, 1)
. A beam ABC of length L is simply supported at one and A and at end B, at a distance x from the free end C. The beam carries a udl of intensity w per unit length over its entire length. Determine the value of x so that the distribution of bending тотеnt in the span will be Most
10 ft 10 ft Problem # 1 B 8k ft 10 ft Use the Virtual Work as the displacement method. Determine the reactions at Deflection Curves of Actual, Primary and Structure with Redundant Cy. the supports if the support at C is forced upwards 0.15in. Take E = 29000ksi Bkjt %3D and = 600 in^4. Note: Use Cy as the redundant reaction. Use Compatibility Equation: (+1) 0.15 = -Ac + GScc
Force P with 5.05 kN magnitude acts along the parallelepipeds diagonal CE, pointing towards E 290 mm 290 mm 145 mm Determine the magnitude of the moment of Pabout the following Ines in N-m. (a) Ine OA N-m (b) ine O8 N- m (c) Ine AB N-m (d) Ine BF N-m (e) ine BG N-m (r) Ine DG N-m (a) Ine 0D N-m (h) Ine OC N-m (1) ine EF N-m (1) Ine OF
USE MOMENT DISTRIBUTION METHOD. Given the indeterminate beam, find the reaction at B in kN. EI is constant. A 5KN/m 5m B 2m 10 KN 3m
From the given beam, determine the rotation at C (in rad) due to the applied loads. Use I =4883x106 mm4 E = 200GPa El=Constant 60KN 300kN m A C k 5m -5m 0.00079 0.00047 0.00098 0.00055 B
Use the yiupn of the parabola to fill in the table. 10- (a) Does the parabola open upward or downward? O upward O downward .0. None (b) Find the equation of the axis of symmetry. -10 equation of axis of symmetry: || (c) Find the intercept(s). For both the x- and v-intercept(s), make sure to do the following. • If there is more than one, separate them with commas. • If there are none, select "None". x-intercept(s):|| y-intercept(s): (d) Find the coordinates of the vertex. vertex:
10 ft 10 ft Problem # 1 8 k· ft 10 ft Use the Virtual Work as the Deflection OCurves of Actual, Primary and Structure with Redundant Cy. displacement method. Determine the reactions at the supports if the support at C is forced upwards 0.15in. Take E = 29000ksi and l= 600 in^4. 8 kft 1oft Note: Use Cy as the Use Compatibility Equation: redundant reaction. (+ 1) 0.15 -Ac + Gfcc
theta = 33 degreesM1 = 450 NmM2 = 550 NmM3 = 650 Nm a. Find the x-component of the resultant moment (in N-m). b. Find the y-component of the resultant moment (in N-m). c. Find the z-component of the resultant moment (in N-m).d. Find the angle of the resultant moment with respect to the positive x-axis (alpha in degrees).e. Find the angle of the resultant moment with respect to the positive y-axis (beta in degrees).f. Find the angle of the resultant moment with respect to the positive z-axis (gamma in degrees).g. Find the magnitude of the resultant moment (in N-m).
Find the value of β and P. (Disregard F1=60kN)
wo (a) Obtain the total elongation of a steel bar of cross-sectional Area 1250mm² acted 2. by forces indicated in the diagram below. E=205,000N/mm2 15N- SN 20N.. 40N 15N 1.5m 1.5m 3m 1m
(a) Using the slope-deflection equations, determine the end moments of members AB and BC of the beam shown below, (b) determine the reaction at B. EI is constant. 2 m 2 m 2 m A 30 kN 30 kN 30 KN 2 m B 3m A 3 m c 50 kN/m upward