Situation 2: The 6 m radius cylindrical gate shown in figure is 10 m long into the paper, if 0 = 40° determine the following B A 0 0 32. The vertical component of the hydrostatic force is? 33. The horizontal component of the hydrostatic force is? 34. The location from point O the vertical components of the hydrostatic force?

Situation 2: The 6 m radius cylindrical gate shown in figure is 10 m long into the paper, if 0 = 40° determine the following B A 0 0 32. The vertical component of the hydrostatic force is? 33. The horizontal component of the hydrostatic force is? 34. The location from point O the vertical components of the hydrostatic force?

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

3. A rigid bars shown in the figure are separated by a roller at C and pinned at A and D. A steel rod at B helps support the load of 50 KN. Compute the vertical displacement of the roller at C Answer: displacement = 2.82 mm E 200 X 10° N/m? %3D A = 300 mm? 50 kN L = 3 m 2 m 2 m A B 3 m 1.5 m II ()
Q3: Three forces are acting on a steel plate with 4m length by 4m width shown in figure. These three forces are required to cause a horizontal resultant acting through point A. If F = 405N, %3D 1) The value of horizontal resultant R is: A.
SITUATION 8: A suspended bar system consists of two cross sections as shown in the figure. Initially its lower surface is 0.8 millimeters above the ground surface. Take E=205 GPa. 80 I1.2 m mm? 160 40 kN mm2 0.8 mm 20. Determine the stress in the 160 mm2 section when a load of 40kN is applied as shown. a. 90.8 MPa b. 204.6 MPa с. 318.3 МPа d. 147.7 MPa 21. Determine the stress in the 80mm2 section when a load 40 kN is applied as shown. а. 90.8 MPа b. 204.6 MPa с. 318.3 МРа d. 147.7 MPa |42.4 m>4
All Elements have a fixed value of E and I. Do load modelling for 1 meter strip width in the water tank section of wwwwww www.www the system.Draw the M N T diagram of the entire system. n=47 6 m. A ΔΒ B 7 water 8 m D 2 m. 47ton 3 m. E 1/10
CLO 1: Determine the maximum tensile stress in MPa if P = 115 %3D kN. 20 mm 25 mm 20 mm 45mm 3somm 16.064 28.395 45.176 10.040 46 mm
2:37 6.00 KB/S A 2M 3M B Problem 2: A rigid block of negligible mass is supported by three symmetrically spaced rods as shown. Each copper rod has an area of 900mm2 and E=120GPA, and the allowable stress is 70MPa. The steel rod has an area of 1200mm2, E=200GPA and the allowable stress is 140MPA. Determine the largest load P which can be supported. Your answer Figure for Problem 2 STEEL 24OMM COPPER COPPER 16OMM 16OMM --
Question 3 A beaker of water has a radius R = 0.06m and a contact angle 0 = 3.6 degrees. Calculate the surface tension force around the interface of the water with the perimeter of the beaker. Determine the horizontal and vertical components of the force.
Q3: Three forces are acting on a steel plate with 4m length by 4m width shown in figure. These three forces are required to cause a horizontal resultant acting through point A. If F = 405N, %3D 1) The value of horizontal resultant R is: E D P. B.
Block A is connected to Block B by Rod 1, and Block B is connected to Block C b y Rod 2 as shown in the figure. Determine the minimum weight of Block A that will prevent the blocks from slidin g down the planes. Use μ = 0.20 for all surfaces. Block A W Rod 1 Enter your answer Block B 20 KN 10° 30° Rod 2 Block C 20 KN 80°
Problem #1: All the vertical bars are constructed from steel (E = 29,000 ksi and a = 6.5 x 10 1/°F). The mechanical loading is shown and in addition the entire system undergoes a uniform temperature change of AT = 25 °F, determine the vertical displacement at point B (red circle). Note the cross- sectional area for all the vertical bars is 0.0750 in? and assume the horizontal beams are rigid. Report your answer in inches to four decimal places. E F 4 ft H. D C -2 ft- 5 ft 4.5 ft 800 lb A B 1 ft
0.1m 0.3m 0:1m Question (C) A beam with the cross section shown in the figure is subjected to a shear force V 100 kN and a bending moment M-150 kN.m. a) Areamoment of inertia about the neutral axis mm r- b) The maximum bending stress= MPa [ c) The shear stress at the neutral axis = MPа 100 mm 100 mm 120 mm 120 mm 120mm M.
The horizontal top of a concrete column is subjected to the system of forces shown. Represent the resultant of all forces as a force Rat point O and a couple M. Also specify the magnitudes of R and M. Your answer is partially correct. 0.6 m 2 kN 1 kN Answers: R=( R= 8 M = ( i 4 KN -0.8 11.045 M = 5.186 0.6 m 3 KN 0 1 KN 7 KN 0.2 m 0.2 m 3 kN KN 7 i+ kN.m 0.5 m 7 kN 0.2 m 0.5 j+ -3 j+ i -5.1 k) kN k) kN-m