Sieve Size, Amount Retained, g Amount Sieve Size, mm Retained, g mm 25 1.18 891.5 19 376.7 0.60 712.6 12.5 888.4 0.30 625.2 581.5 9.5 506.2 0.15 4.75 1038.4 0.075 242.9 2.36 900.1 Pan 44.9

Q: Below is a sieve analysis for a fine aggregate. a. Complete the sieve analysis to get percent…

A:

Q: A sieve analysis test was performed on a sample of fine aggregate and produced the following…

A: Sieve (mm) Amount retained (g) %Retained Cumulative retain % passing 4.75 0 0 0 0 2.36 33.2…

Q: The following table shows the results obtained from Wash Test done on samples of fine aggregates.…

A:

Q: 1. Three samples of aggregates are sieved to obtain the grading curve. A set of different sieves is…

A: Note : Since you have asked multiple questions, we will solve the first question for you. If you…

Q: From the given data shown in the table below, determine the effective specific gravity of…

A:

Q: ry condition

A: Given that 10 Kg sample of an aggregate Moisture Content= 0.07%Now

Q: From a Coarse Aggregate sample, the ff data are given below to determine the sample's specific…

A: Given data, Oven dry mass A = 3625.5 g SSD mass B = 3650.3 g Mass under water C = 2293.0 g

Q: 1)Determine the uncorrected and corrected weights based on the following data using the traditional…

A: Following is required mix design procedure :

Q: The mass of a bulk density bucket is measured as 21XY g when it is empty. (Where XY are the last two…

A: Bulk Density of aggregate: The Bulk density of aggregate also known as Unit weight of an aggregate…

Q: The data gathered from an experiment to determine the specific gravity of aggregates were summarized…

A: Given data: Weight of FA sample w1= 171.06 gm weight of SSD sample w2= 175.38 gm weight of…

Q: Q3) The result of sieve analysis of a sample of aggregate given in the Table below. According to…

A: Sieve analysis: It is an analytical method that is used to determine the particle size distribution…

Q: The result of specific gravity test is given below Weight of saturated aggregate in water =618gm…

A: Given, Weight of saturated aggregate in water= 618gm Weight of oven dried sample= 982gm Weight of…

Q: 46.5 kg (102.3 lb) of fine aggregate is mixed with 72.3 kg (159.1 lb) of coarse aggregate. The fine…

A: The given data is shown below:

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A:

Q: Three aggregates are to be mixed together in the following ratio: Aggregate A 35% Aggregate B 40%…

A: The following concept and formula are used to determine the percent passing each sieve for the…

Q: 5. The table below represents data from sieve analysis carried out on a coarse aggregate Determine…

A:

Q: The sieve analysis results for fine aggregate (1000 g) are shown below, complete the following table…

A:

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: Given that,   The volume of rigid bucket= 0.2 ft3      Weight of empty bucket= 18.2 lb  Weight of…

Q: A results of sieve analysis test for sample of Aggregate are shown in below Table: Sieve Size Wt…

A: Since we only answer up to 3 sub-parts, we’ll answer the first three. Please resubmit the question…

Q: . For an aggregate sample, if you know that the apparent relative density is 2.72 and the water…

A: The apparent relative density is 2.72. Water absorption is w=1.2%. The dry mass of aggregates is…

Q: 5.28 Table P5.28 shows the grain size distributions of two aggregates A and B. TABLE P5.28 Sieve…

A: The grain size analysis is prominently used in the classification of soils. The data is obtained…

Q: the nominal Maximum aggregate Size for the aggregate gradation shown below is equal to Sieve size…

A: Maximum Aggregate Size: Maximum Aggregate Size is the smallest size size which requires 100%…

Q: Table P5.27 shows the grain size distributions of aggregates A, B, and C. The three aggregates must…

A: The solution is in step 2:

Q: Calculate the bulk specific gravity of combined aggregate if you know the specific gravities of…

A:

Q: A sieve analysis test was performed on a sample of coarse aggregate and pro duced the following…

A: as per our guidelines we are suppose to solve only 3 sub part per post .kindly repost other sub part…

Q: The sieve analysis results of two fine aggregates are given below in Table 1. a) Calculate the…

A: The expression for fineness modulus is given as FA1=∑100-%P100 % passing 100-%passing 100 0…

Q: Determine the difference between the Rodded and Loose Unit Weight of aggregates

A: Difference between Rodded and Loose unit weight

Q: The following table shows the results obtained from laboratory tests done on samples of aggregates.…

A:

Q: Calculate the sieve analysis shown in Table P5.20, and plot on a 0.45 power gra- dation chart. What…

A: The given table is shown below:

Q: 4. A sieve analysis test was conducted on a representative sample of a concrete aggregate material…

A: If we assume 1000 g of aggregate was taken for the test.

Q: Thoroughly mix the aggregate sample and reduce it to an amount suitable for testing, using a sample…

A: Sample Splitters: Sample splitters work by reducing the sample size by leading the flow of the…

Q: Determine the Fineness Modulus of the given aggregate data, determine what kind of aggregate based…

A: Given  Sieve Analysis results table

Q: The following table shows the results obtained from laboratory tests done on samples of aggregates.…

A: Answer We are given  Bulk specific gravity of SSD  = 2.67 Weight of aggregates+metal container ( Wam…

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A:

Q: 6. A sample of lightweight coarse aggregate weighs 532.3 g when oven-dried, 615.7 g when saturated…

A:

Q: Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced…

A: a). percent passing  Sieve Size(mm) Weight Retained Percentage Retained Cumulative Retained…

Q: Question # 3: Caleulate the fineness modulus of aggregate according to the table of the sieve…

A: Given that:

Q: rodded coarse aggregate: Trial 1 =34,75 kg Trial 2 =34.06 kg Trial 3 =35.74 kg a. Calculate the…

A:

Q: 1. Determine the Specific gravity of aggregate based on the following values: Mass of empty…

A: Given data Mass of empty container: M1 kg Mass of container+ Aggregate: M2 kg Mass of container+…

Q: (a) A specific gravity test was performed on a sample of fine aggregate and produced the following…

A: A=510g B=1550g C=1900g S=520g

Q: 1) Given the following results of sieve analysis of coarse aggregates: Weight Retained (lb) Sieve…

A: Im answering you have required part c only. For that we will require table and a graph as below

Q: You are given a result of the gradation test of aggregate, calculate and plot the gradation curve on…

A: Weight % weight  cumulative %   cumu %  sieve size  retained  retained  retained passing 5 0 0…

Q: if total sample mass of aggregate is 164.9 grams, then the percent passing from sieve size #50 only…

A: The given data is: Total sample mass of aggregates (WT) = 164.9 g

Q: Sieve Size Amount Retained, Ib 3 in. 2 in. 1-1/2 in. 3.7 1 in. 15.9 3/4 in. 12.0 1/2 in. 13.5 3/8…

A: Given  Sieve Analysis table    Typical range of fineness modulus of sand

Q: A sieve analysis test was performed on a fine aggregate sample. The total weight 2) of the sample…

A:

Q: 500 gm oven dry fine aggregate was tested to find its physical properties. The output from the test…

A: Solution: Given Data: Weight of dry fine aggregate  X=500 gm X1=mass in wet condition 518 gm S=SSD =…

Q: Below is a sieve analysis for a fine aggregate. a. Complete the sieve analysis to get percent…

A:

Q: According to fuller equation, to draw the maximum density line for aggregate gradation shown below,…

A:

Quantity takeoff

Quantity takeoffs (QTO) are precise estimates of the materials and labor costs required to finish a construction project. During the pre-construction phase, an estimator prepares them, breaking down the project into smaller, more manageable parts that are easier to evaluate. These measurements are used to prepare a construction scope bid. Estimators examine the drawings, specifications, and models to figure out different quantities and their costs. Since, the components, their quantity, and price are all included in the model, quantity take-off can be done automatically using Building Information Modelling (BIM). The time taken for completing a construction project can be reduced by the use of quantity takeoff. These takeoffs are also called material takeoffs and construction takeoffs.