SAE 30 oil at 20°C (p= 891 kg/m³ and u= 0.29 kg/m s) flows in the 3-cm-diameter pipe as shown in Figure below, which slopes at 37°. The pump is added between A and B to drive the oil upward from A to B at a rate of 10 kg/s. At 100% efficiency, Determine the head loss (h). O 560.2 m 466.8 m. 580 m P=156 kPa 18 m. 24 m 37 PA 520 kPa

SAE 30 oil at 20°C (p= 891 kg/m³ and u= 0.29 kg/m s) flows in the 3-cm-diameter pipe as shown in Figure below, which slopes at 37°. The pump is added between A and B to drive the oil upward from A to B at a rate of 10 kg/s. At 100% efficiency, Determine the head loss (h). O 560.2 m 466.8 m. 580 m P=156 kPa 18 m. 24 m 37 PA 520 kPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.10) Water, is pumped between two reservoir at 0.005 m3/s through a 100 m of 2 in diameter pipe and several minor losses, as shown in figure. The roughness is ε=0.02 mm. Compute the pump head required to maintain the flow. Z1-6 m Sharp Entrance K=0.8 Gate Valve K= 0.2 Standard Elbow K=0.9 Sharp Exit K= 0.5 Gate Valve K= 0.2 Long radius elbow K=0.2 Z2-30 m
6) Through the pipeline system in the figure, calculate the flow velocity and flow rate at B, if Pa = 10 mwl. Ignore energy losses. 5 14.89 m A 15 m 15 m Mercury 2. 1 15 m 3 7 B
This is a fluid machine question. Water reservoir is pumped over a hill through a pipe 450 mm in diameter and a pressure of 98.08 kPa is maintained in the summit water discharge is 30 m above the reservoir. The quantity pumped is 0.50 m3/s. rrictional losses in the discharge and suction pipe of the pump is equivalent to 1.5 m head loss. The speed of the pump is 800 rpm, what amount of energy must be furnished by the pump in kW?
water at 20°C is pumped through a smooth 12-cm-diameter pipe 10km long, at a flow rate of 75 m3/h. The inlet is fed by a pump at an absolutepressure of 2.4 MPa.The exit is at standard atmospheric pressure (101 kPa) and is 200 mhigher.Calculate the frictional head loss Hf and compare it to the velocity head of the flow.B) A gate valve is used to control flow in the above system. What is the headloss due to the addition of the valve?What is the total head loss in the new system?state any assumptions made. for the value fully open k=0.17, 3/4 open k=0.9, 1/2 open k=4.5 and 1/4 open k=24
Question 5: The pump shown below delivers a head of 50 m to the water through 30 cm diameter with pipe length 500 m. If the head loss is given by determine. L V² 0.02 / 1. The flow rate (Q) through the system in m³/s 2. The input power (Pi) required to supply the pump if the efficiency=75% 2 40 m L w **** AVB
Q.2.A. Blood flows through the branching blood vessels as shown in figure at a rate of 1o Aln ft/s. If viscous effects are negligible, determine the water speed at section (2), the 10 ts pressure at section (3), and the flow rate at section (4). Palood 1000 kg/m (1) A 0.2 (3) V 20/s P- 10 psi (2) Ag 0.07 ? 5.0 psi
A 60L/s of heavy oil, p-980kg/m² and v-400mm³/s, is flowing in a 305-mm-diameter pipe. The starting elevation of pipe is z1=85m, the end elevation of pipe z,=105m, and the length of pipe l=1800m. Determine the pressure drop and power loss in the pipe.
oil CM=0-08372 Pa.s, S6= 0.843 is flowing from the Upper to lower reservoir at a rate of o028/s through a 15 cm & smooth pipe. Calculate the elevation of oil and the upper reservoir. S. pipe o= 15cm El OIL Gom Kc=05 go bénd El 130m oil 130m
Oil ( µ = 0.478 Pa.s and v= 5.3 *10* m/s ) flows downward in a pipe ( 3 cm ) in diameter and has a slope of ( 30° ) with the horizontal. The gradient along the pipe is ( dp/dx = - 918.5 N/m³ ). Determine; 6. a. The volume flow rate. b. The wall shear stress. c. The maximum and average velocities. d. The Reynolds number.
At the gasoline transfer facility (ρᵣₑₗ=0,75) from the pond of storage to consumption, you want to install a pump to circulate a flow of 40(lt/s). The 400m long pipe is cast iron 150mm in diameter and consists of a check valve, a gate valve and 2 commercial medium radius elbows. The consumption tank is pressurized to 2,9 (kgf/cm²) gauge pressure. Decide the drive power of the pump in KW if its performance is 70%. •Additional data, pressure drop factors: •Retention valve Kᵣ = 1,5 •Gate valve open Kᵥ = 0,21 •Medium Radius Commercial Elbow Kc = 0,75 for each cubit •Storage pond outlet sharp angles Kₛ = 0,5 •Entrance to consumption pond Kₑ = 1 •Friction factor in pipes f = 0.026
The 20 m long pipe between the A and B tank in the figure is made of cast iron and its flow rate is Q = 0.0020m ^ 3/s. Find %3D the required pipe diameter, ignoring losses and friction Yükseklik = 2 m Toplam Uzunluk = 20 m YOkseklik= 0 m B.
Oil ( u = 0.478 Pa.s and v = 5.3 *10* m'/s ) flows downward in a pipe which is ( 3 cm ) in diameter and has a slope of ( 30°) with the horizontal. The pressure gradient along the pipe is ( dp/dx = - 918.5 N/m ). Determine; 6. a. The volume flow rate. b. The wall shear stress. c. The maximum and average velocities. d. The Reynolds number.