Road width (6 m), side slope ½, H.I = (31.33m) formation level = (26.05 m), staff reading at a= 1.65m and b=2.20m find the depth of cut for the three points X, X, H. H, K H.I F.L Datum Ha=6.93m ,HB3D7.48m Ha=3.63m ,Hb%3D3.08m Ha=6.93m ,Hb=3.08m O Ha=3.63m ,H%3D7.48m O

Road width (6 m), side slope ½, H.I = (31.33m) formation level = (26.05 m), staff reading at a= 1.65m and b=2.20m find the depth of cut for the three points X, X, H. H, K H.I F.L Datum Ha=6.93m ,HB3D7.48m Ha=3.63m ,Hb%3D3.08m Ha=6.93m ,Hb=3.08m O Ha=3.63m ,H%3D7.48m O

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A rectangular flume of planed-timber (n=0.012 is 1.5m wide and carries 2.00m /s of water. The bed…

Q: Classify the channel bed slopes. Write the methods of calculating length of GVF profile and explain…

A: Flow profiles are classified by the slope of the channel S0, critical slope Sc, normal depth of the…

Q: 1. A partially open sluice gate in a 5-m-wide rectangular channel carries water at 10 m/s. The…

A: Given y1 = 2.5 m Q= 10m3/s b= 5 m

Q: e = 20° - 4 m- Stream Rock outcrop Canal B

A: Given data: QA=0.25×10-4 m/sPA=3 kPaPB=2.5 kPaL=4 m

Q: The width of formation level of a certain cutting is 15m and the side slopes are 1: 2. The surface…

Q: This wood flume has a slope of 0.0015. What will be the discharge of water in it for a depth of 1 m2…

A: Solution;

Q: PROBLEM 1 -Given the following sections 1+020 a +0.90 +3.5 +0.55 1+080 -1.85 -1.20 -0.42 Base for…

A: Given, FILL: Base for fill= 12 m side-slope = 1:1 CUT: Base for cut= 12 m side-slope = 2:1 Distance…

Q: During fly levelling, the following note is made : B.S. = 0.62, 2.05, 1.42; 2.63 and 2.42 metres…

Q: 1. What is the wetted area for a triangular channel having depth y and the side slope being Z? a)…

A: The wetter area for a triangular channel having depth y and the side slope being Z

Q: 5 kN 2.5 kN/m

Q: 5.18 A cut is made in a stiff, saturated clay that is underlain by a layer of sand. What should be…

A: To find the height of the water (hw) -

Q: Q3). From the followings: St. 1: h=0.5m cut at center line, s = 4 assume right side higher than left…

Q: al section, bottom width 4.91 m., side slopes 1H to 2V at a depth of 2.41 m. The canal is on a slope…

A: Given data Bottom width, B=4.91m Depth, d=2.41m Side slope=1H:2V Canal slope=0.00089 Coefficient of…

Q: A horizontally laid circular pipe culvert having an elevation of its top to be 26m crosses at right…

Q: A rectangular channel 4.8 m wide and 1.4 m deep was laid to have a hydraulic slope of 0.0017. Using…

Q: A thick layer of stiff saturated clay is underlain by a layer of sand. The sand is under artesian…

Q: :A puncture of length 250 m, with a trapezoidal section and slope of the sides 1: 1.5, the value of…

A: Solution Given that Length of channel L=250 m n=0.005 side slope x=1.5 The slope of the floor…

Q: Q5. (P.) A 30 m height slope is to be built as shown below. The homogeneous with c' = X kN/m² and o'…

A: Given: C'=X=35KN/m2 ϕ'=Y=30°γsat=Z=19.5KN/m3Yw=10KN/m3F.Scheck=2 Radius of Arc = 30m To Find: The…

Q: - The following notes refer to three level cross-sections work in cutting. Station 1 C 2.0 C 2.4 C…

Q: 1. What is the hydraulic radius for a rectangular channel section? a) Зу b) 2y с) у d) y/2

Q: 1. From the given cross-section notes, compute the volume of earthworks between the two stations.…

A: Solution: 1. Given data: Station = 12+440 m h1 = 4 m h2 = 8 m h = 6 m Slope = 2:1 L = 20 m B = 20 m…

Q: A rectangular channel 6 m wide and 1.5 m deep has a slope of 1 in 1200 and is lined with good rubble…

Q: Excavations in open cuts in excess of depth shall have adequately designed shoring on support. 2.5 2…

A: To Determine At what depth of excavation in open cuts designed shoring on support is required.

Q: A triangular channel has a 30-degree walls. A smooth asphalt lining (n = 0.013) is used and the…

Q: For an anchored retaining wall, the ground anchor is located at z=6.0m above the lower grade and is…

A: Location of ground anchor = 6.0 m above the lower grade Inclination of the anchor with horizontal =…

Q: A rectangular flume of planed-timber (n=0.012 is 1.5m wide and carries 2.00m/s of water. The bed…

Q: a triangular shaped channel is to be designed to carry 741 L/s on a slope of 0.0152. assuming that…

Q: A rectangular channel of best hydraulic cross-section, n = 0.016, is laid on a slope of 0.0064 and…

Q: A cut is to be made in a soil having y = 105 pcf, c = 550 psf, and = 15°. The slide of the cut slope…

A: Unit weight of soil(γ)=105 pcf The cohesion of soil(C)=550 psf the angle of friction(ϕ)=15o Slide…

Q: Problem 6 The formation width of a certain cutting is 8 m and the side slope is 1: 1. The surface of…

A: Given: The width is 8 m. The side slope is 1:1. The ground surface has a uniform slope of 1 in 10.…

Q: 1) Which statement is correct about Point A at station 20+00? a) No earthwork is needed at this…

A: 1. At point A, the cumulated volume is zero. From the mass diagram earthwork is required for cut and…

Q: span. N, 2 m to the right of A; and C = 50 kN, 6 m to the right of B. Determine the noment at C in…

Q: . A vertical cut is made through a homogeneous soil mass (c=20 kPa,ϕ=20°,γ=16.50 ?? ?3 ⁄ ). Estimate…

Q: rectangular canal, 6.54 m wide and 1.54 m deep lined with smooth stone ( n = 0.013) Has a hydraulic…

A: Find Saving in earth work and lining??

Q: c) A trench needs to be constructed at a certain saturated clay underlain by a layer of sand as…

Q: A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports th Assume…

Q: Given the cross-section notes of an earthwork between Station 10 + 100 to 10 + 200. Assume both…

Q: For the infinite slope find the FS against slip (AB), with the data H = 26 ft, Gs = 2.6 e = 0.5 Φ =…

Q: On the trapezoidal finished-concrete channel shown below. Given y = 2.45ft, B= 3ft, and angle 0 is…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: This wood flume has a slope of 0.0015. What will be the discharge of water in it for a depth of 1 m?…

A: step 1-

Q: Q3). Calculate the cross section area of cut and fill for the followings: St. 1) h = 2m cut at…

A: Cut and Fill : Cut and fill is the process in which earthen material of a road or canal removed or…

Q: A 6m vertical cut has been excavated from a dry cohesive loess soil deposit. For the plane shown…

A: Dry density of soil = γd = 15KNm3 Cohesion = c = 10Kpa ϕ = 11°

Q: or a triangular channel having a side slope of Z horizontal: 1 vertical,

Q: The areas in cut of two points of level sections that are 75m apart are 36sqm and 72sqm. Side slope…

Q: horizontally laid circular pipe culvert having an elevation of its top to be 26m crosses at right…

Q: O Determine the dimensions of a trapezoidal best section of an open channel whose sides have a slope…

Q: Q.5 What are the key differences between Kennedy's method and Lacey's method of channel design?

A: Brief concept introduction- Lacey's Theory- It states that the vertical component of the eddies…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

Road width (6 m) , side slope 2, H.I =
(31.33m) formation level = (26.05 m), staff
reading at a= 1.65m and b=2.20m find the
.depth of cut for the three points
x,
X,
H,
H,
K
H.I
F.L
Datum
Ha=6.93m ,Hb%3D7.48m
Ha=3.63m ,Hb%3D3.08m
Ha=6.93m ,HB3D3.08m
Ha=3.63m ,Hb%3D7.48m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Given the following section of an earthwork for a proposed road construction on a hilly portion of the route. The width of the road base for cut is 6m for allowance of drainage canals and 5m for fill. Slide slopes for cut is 1:1 and for fill is 1:5:1 Sta. B 3.7 -0.8 +1.8 a. Compute the value of X b. Compute the area in fill. c. Compute the area in cut.
Given the following section of the earthwork, the width of the road base for a cut is 7m and 6m for fill. The side slope for cut and fill are 1.5:1 -3.7 +0.8 -1.8 Compute the value of x and the area of fill. b. What is the are of cut а.
: Workout the Earthwork quantities in embankment and cutting for the chainage length of 600 meters. Formation width is 20m. Side slopes in embankment is 2:1 and in cutting is 1.5:1. There is no transverse slope. Rising gradient of 1:250 upto 250m chaniage. Rising gradient of 1:100 upto 600m chainage. Chainage 0 50 100 150 200 250 300 350 R.L of Ground 152.0 152.35 152.6 152.8 153.0 152.6 152.2 151.5 R.L of Formation 151.6 Chainage 400 450 500 550 600 R.L of Ground 151.2 150.5 150.3 150.5 150.7 R.L of Formation 155.4
The center height of the road @ STA 7+110 is 2.0 m while @ STA 7+160, it is 1.20 m cut. From STA 7+110 to the other station, the ground makes a uniform slope of 4.8%. How far in meters from STA 7+160 toward STA 7+110 will the excavation extend? Answer: 18.75 m
3) Module 14 - Earthworks The following shows cross-section notes for a road grading work. 3.5 x2 x1 -3.2 1.2 1.2 2.8 In addition, the road width is 9m and the side slopes for cut is 1:1 and for fill, 1.5:1. Determine the Volume of CUT and the volume of FILL if the cross-section for earth works is constant all throughout a 31.6m length of road.
Question 2. Below shown is the profile for a road construction at a station. This is a fill section. Sometimes the letter C is used to designate cut and F to indicate fill for the vertical distance or depth. In other words, a point below the base would have a negative sign in a fill section. F 11.8 below corresponds to -11.8 ft. The baseline is 50ft. Calculate the area for the fill section. (Answer: 137.3 yd²) 50ft F 11.8 -42.5 F 14.3 -32.0 0 -25 25 olo F 15.8 25 25 Baseline F 16.3 65.4
6. Given the following section of an earthworks for a proposed road construction on a hilly portion of the route. The width of the road base for cut is 6 m for allowance of drainage canals and 5 m for fill. Sides slopes for cut is 1:1 and for fill is 1:5:1. 3.7 -0.8 +1.8 a. Compute the value of x b. Compute the area in fill C. Compute the area in cut
Q) Two irregular sections 60 m apart have areas in cut of 32 m2 and 68 m2. The base width is 8 m and the side slope is 1:1. Find the corrected volume of cut between the two stations using the prismoidal correction formula Corrected volume of cut = __________m3 Solve it early
1. Given the following cross-section notes of an earthwork on a rolling terrain Sta 5+-000 +10 +5 +3 31 13.5 Sta 5+-020 +14 +7 +4.5 41 17.25 The width of the road is 12 m and the slide slope is 2.5:1 a. Compute the volume using end area with prismoidal correction.
Compute the area given the following cross section notes: Base for cut = 9m and for fill -8 m. Side slope for cut 1:1 and for fill 1.5:1. LEFT CENTER RIGHT -1.84 -1.22 -0.42
Calculate the side widths and cross-section area of embankment having width =20m and side slope( 1/2 )formation level =20m . ground level=15m and ground slope ( 1/12) from C.L to side
The in cut of two irregular sections 35m apart are 34m? and 56m², respectively. The base width is 10 meters and the side slope is 1:1. Find the corrected volume of cut in m3, using prismoidal correction. ASsume that the cross section is a regular isosceles trapezoid (height at the center and sides are equal.)